National Instruments NI 78xxR - Manual
National Instruments NI 78xxR – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Start»All Programs»; Unpacking; Caution; R Installation; Note; Step 1. Install Application Software and Driver; Caution
- Page 3 – Installing an NI PCI-78; Measurement & Automation; icon on the desktop to open Measurement &; Devices and Interfaces; Verify that the device appears under; Devices and Interfaces»RIO Devices
- Page 4 – Step 3. Connect Signals; R Digital R Series devices.; R Connector Pin Assignments and Locations
- Page 6 – Connectivity Options; R Series Connectivity Options; Cable; to the SCB-68 terminal block
- Page 7 – Step 4. Using Your NI 78; R Device with a LabVIEW FPGA Example VI
- Page 9 – Adding Analog Output to the FPGA Application
- Page 11 – Where to Go From Here
- Page 12 – — Describes the electrical and mechanical aspects of the NI 78; manuals; —Describes the electrical and mechanical aspects of the NI 781; Where to Go for Support; support; outside the United States, contact your local branch office:
Getting Started with R Series Intelligent DAQ
This document explains how to install and configure National Instruments 78
xx
R devices.
Figure 1.
PCI and PXI R Series Devices
NI 78
xx
R Required Components
The following items are necessary to set up and use the NI PCI/PXI-78
xx
R:
❑
The following software packages:
–
LabVIEW 7.1 or later
–
LabVIEW FPGA Module 1.1 or later
–
NI-RIO 1.3 or later—included with the NI 78
xx
R
–
(Optional)
LabVIEW Real-Time Module 7.1 or later
Note
The examples referenced in this document require LabVIEW 8.0 or later and NI-RIO 2.0
or later.
❑
Development computer or PXI/CompactPCI chassis and PXI/CompactPCI embedded controller
running Windows 2000/XP.
❑
At least one cable and device for connecting signals to the NI 78
xx
R.
Step 1. Install Application Software and Driver
Before installing the NI 78
xx
R, you need to install the application software and device driver.
Note
The NI PXI-7831R supports LabVIEW 7.0 or later, LabVIEW FPGA Module 1.0 or later,
and NI-RIO 1.0 or later. The NI PCI-7831R and NI PXI-7811R support NI-RIO 1.1 or later.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Getting Started with R Series Intelligent DAQ 2 ni.com Refer to the LabVIEW Release Notes for installation instructions for LabVIEW and system requirements for the LabVIEW software. Refer to the LabVIEW Upgrade Notes for additional information about upgrading to the most recent version of LabVIEW fo...
© National Instruments Corporation 3 Getting Started with R Series Intelligent DAQ Figure 2. Installing an NI PCI-78 xx R Device Figure 3. Installing an NI PXI-78 xx R Device in a PXI Chassis 5. For the NI PCI-78 xx R, secure the device mounting bracket to the computer back panel rail. For the NI PX...
Getting Started with R Series Intelligent DAQ 4 ni.com Step 3. Connect Signals Figure 4 shows the I/O connector pin assignments and locations for NI 781 x R Digital R Series devices. Figure 5 shows the I/O connector pin assignments and locations for NI 78 xx R Multifunction R Series devices. Figure ...
