National Instruments NI 5412 - Manual
National Instruments NI 5412 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – Frequency and Transient Response; Specification
- Page 7 – Sample Clock
- Page 9 – System Phase Noise and Jitter (10 MHz Carrier)
- Page 11 – CLK IN; (Sample Clock and Reference Clock Input, Front Panel Connector)
- Page 12 – PFI 0 and PFI 1
- Page 13 – Start Trigger
- Page 15 – Markers
- Page 16 – Waveform and Instruction Memory Utilization
- Page 17 – Memory Limits
- Page 19 – Software
- Page 20 – Environment; Specifications
- Page 23 – Notes
- Page 24 – Physical
- Page 25 – Where to Go for Support
NI 5412 Specifications
NI PXI/PCI-5412 14-Bit 100 MS/s Arbitrary Waveform Generator
Unless otherwise noted, the following conditions were used for each
specification:
•
Interpolation set to maximum allowed factor for a given sample rate.
•
Signals terminated with 50
Ω
.
•
Low-Gain Amplifier Path set to 2 V
pk-pk
, and High-Gain Amplifier
Path set to 12 V
pk-pk
.
•
Sample clock set to 100 MS/s.
Typical values are representative of an average unit operating at room
temperature. Specifications are subject to change without notice. For the
most recent NI 5412 specifications, visit
ni.com/manuals
.
To access all the NI 5412 documentation, including the
NI Signal
Generators Getting Started Guide
, which contains functional descriptions
of the NI 5412 signals, navigate to
Start»Programs»National
Instruments»NI-FGEN»Documentation
.
Caution Hot Surface
Allow the NI 5412 to cool before removing it from the chassis to reduce
risk of burns. Use caution when handling because recently used NI 5412 devices may
exceed safe handling temperatures.
Contents
CH 0 ........................................................................................................ 2
Sample Clock .......................................................................................... 7
Onboard Clock ........................................................................................ 10
Phase-Locked Loop (PLL) Reference Clock .......................................... 10
CLK IN ................................................................................................... 11
PFI 0 and PFI 1 ....................................................................................... 12
Start Trigger ............................................................................................ 13
Markers ................................................................................................... 15
Waveform and Instruction Memory Utilization...................................... 16
Calibration............................................................................................... 18
Power ...................................................................................................... 18
Software .................................................................................................. 19
Environment ............................................................................................ 20
Safety, Electromagnetic Compatibility, and CE Compliance ................. 22
Physical ................................................................................................... 24
Where to Go for Support ......................................................................... 25
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NI 5412 Specifications 4 ni.com Frequency and Transient Response Bandwidth 20 MHz –3 dB Digital Interpolation Filter Software-selectable Finite Impulse Response (FIR) filter. Available interpolation factors are 2, 4, or 8. — Passband Flatness Low-Gain and High-Gain Amplifiers Path — ±1.0 dB from DC ...
© National Instruments Corporation 7 NI 5412 Specifications Sample Clock Spectral Characteristics (Continued) Average Noise Density Path Amplitude Range Average Noise Density Average Noise Density at small amplitudes is limited by a –148 dBm/Hz noise floor. V pk-pk dBm dBm/Hz dBFS/ Hz Low-Gain 2 10 ...
© National Instruments Corporation 9 NI 5412 Specifications System Phase Noise and Jitter (10 MHz Carrier) Sample Clock Source System Phase Noise Density (dBc/Hz) Offset System Output Jitter (Integrated from 100 Hz to 100 kHz) 1. High- Resolution specifications vary with Sample Rate. 2. All values a...
