National Instruments cFP-21xx - Manual
National Instruments cFP-21xx – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Mount the Compact FieldPoint Backplane; backplane on a 35mm DIN rail, on a panel, or in a; Keep in mind these requirements for space and cabling
- Page 3 – If you are using UL Recognized I\O modules with the Compact
- Page 4 – NI recommends that you use one of the mounting systems
- Page 5 – Mounting the Backplane on a Panel; using a; Do not use screws longer than 5/16 in. to fasten the
- Page 7 – Disconnect power before removing the backplane from the; Mounting the Backplane on a DIN Rail
- Page 8 – Do not use screws longer than 5/16 in. to fasten the DIN rail
- Page 9 – Mounting the Backplane in a Standard 19 in. Rack; using the captive
- Page 11 – xx; Controller on the Backplane; Make sure that no power is connected to the controller.
- Page 13 – Install Connector Blocks on the Backplane
- Page 14 – to Your Network
- Page 15 – Wire Power to the Compact FieldPoint System; Cascading power defeats isolation between the cascaded
- Page 16 – DIP Switches
- Page 17 – Install Software on the Host PC; Start»Run; Start»Programs»
- Page 18 – Compact FieldPoint Safety Information
- Page 21 – Using This Product Safely in Hazardous Locations; Explosion hazard—Substitution of components may impair; Specifications; Network
- Page 22 – Memory; and enter; Serial Ports; one RS-485 serial port
- Page 23 – , verified by 5 s test; Power Requirement; Recommended power supply; Physical Characteristics
- Page 24 – Environmental; voltage ratings must be lowered; Shock and Vibration; Operating vibration; Safety
- Page 25 – For UL, hazardous location, and other safety certifications, refer; Electromagnetic Compatibility; FCC 47 CFR Part 15B: Class A emissions; For EMC compliance, operate this device with shielded cabling.; CE Compliance
- Page 26 – Refer to the Declaration of Conformity (DoC) for this product for; Cabling
- Page 27 – Where to Go for Support; you have access to everything from
Quick Start Guide
FieldPoint cFP-21xx
What You Need to Get Set Up
•
cFP-21
xx
LabVIEW RT controller
•
Mounting hardware (DIN rail,
panel-mount, or rack-mount
accessory)
•
I/O module(s)
•
cFP-BP-
x
backplane, connector
blocks, cables
•
11–30 VDC power supply
•
Accessories: Ethernet cable,
number 2 Phillips screwdriver
•
PC running Windows
•
FieldPoint software 4.1.1 or later
•
LabVIEW Real-Time Module
™
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
cFP-21xx Quick Start Guide 2 ni.com 1. Mount the Compact FieldPoint Backplane You can mount the cFP-BP- x backplane on a 35mm DIN rail, on a panel, or in a standard 19 in. rack. Before using any of these mounting methods, record the serial number from the back of the backplane. Each set of mounting ...
© National Instruments Corporation 3 cFP-21xx Quick Start Guide Caution If you are using UL Recognized I\O modules with the Compact FieldPoint system, you must install the entire system in a suitably rated, UL Listed NEMA or IP enclosure. Cabling Clearance Cooling Outline 51 mm (2 in.) All Around 4 ...
cFP-21xx Quick Start Guide 4 ni.com Caution NI recommends that you use one of the mounting systems described in this document. If you decide to use a custom mounting solution, make sure that the screws you use are short enough to fit in the holes in the backplane. The screw holes are 5 mm (0.2 in.) ...
