Msd 50981 DynaForce Starter, Chrysler 318-440 Engines- User Manual
Msd 50981 DynaForce Starter, Chrysler 318-440 Engines– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 4 Wiring the DynaForce High Speed Starter.; • If there is not enough clearance, you will need to install the; Figure 2 Pinion Gear Pattern.; Figure 3 Installing the Pinion Shim Spacers.
- Page 3 – INSTALLATION INFO; SLOW CRANKING; exceeds your starting and electrical system requirements.; Figure 5 Wiring to Incorporate an External Solenoid.
- Page 4 – TECH NOTES; Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D
MSD DynaForce Starter
Chrysler 318-440 Engines, PN 50981
WARNING: Before installing the DynaForce Starter disconnect the battery cables. When disconnecting
the battery cables, always remove the Negative (-) cable first and install it last.
IMPORTANT: Proper installation of the DynaForce Starter is important to the overall operation. Correct alignment
of the starter pinion with the ring gear is needed to achieve the best operation and longevity from
your starter. Please read the instructions before attempting the installation.
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help
if there is ever a warranty issue with your product and helps the MSD R&D team create new products that
you ask for! Go to www.msdperformance.com/registration.
Figure 1 Clocking the Starter
for Clearance.
CLOCKING
LOCATIONS
Thank you for purchasing the DynaForce Starter from MSD. Please be sure to read, understand, and
follow the instructions prior to installation so that everything goes smoothly and the engine starts
reliably time after time.
Parts Included:
1 - Starter
1 - Shim Ring
1 - Outer Shim
INSTALLATION
1. Make sure the starter mounting surface is clean and smooth.
2. Mount the starter and check that the position of the solenoid is
away from direct heat sources and other components. If there
are clearance problems, the starter housing can be rotated to
move the location of the solenoid. This is done by removing
the three bolts on the mounting block and repositioning the
starter motor (Figure 1).
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 4 Wiring the DynaForce High Speed Starter. BATTERY + - LENGTH 3’ 5’ 7’ 10’ +10’ AWG 4 2 1 0 00 CABLE LENGTH VS. GAUGE 12-GAUGE MINIMU...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 INSTALLATION INFO SLOW CRANKING The most common cause is due to low input voltage. The battery should be checked, but also inspect the batte...
TECH NOTES _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _____________________________________________...
