Honeywell RTH6580WF1001 - Installation Manual
Honeywell RTH6580WF1001 Thermostat – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Installing the Honeywell thermostat
- Page 4 – Registering the thermostat; To register the Honeywell thermostat:; Enabling auto mode
- Page 5 – Pairing and removing the thermostat with ClareHome; To pair the thermostat using ClareHome:; ClareHome app’s; Devices
- Page 6 – Read through the displayed information, and then tap; Authorize Device
- Page 7 – Enter your credentials into the Honeywell TCC page and tap; Sign In
- Page 9 – Tap the 3 dots next to the thermostat, and then tap; Remove
- Page 10 – Pairing and removing the thermostat in FusionPro; Follow the below steps to add and remove a thermostat in FusionPro.; To add the thermostat in FusionPro:; Locate the desired account in the list, and then click; View
- Page 11 – tab, and then click; Add Devices
- Page 12 – Honeywell; This will take you to the Honeywell sign in page.
- Page 13 – Enter the customer’s credentials and click; Read through the information presented and click; I Accept
- Page 14 – Once the device is successfully authorized, click; Return to Device List.
- Page 15 – Delete; next to the desired device.
- Page 16 – Contact information
DOC ID - 1188
• Rev 06.02
1 / 16
Honeywell WiFi (Total Connect
Comfort
– TCC) Thermostat Driver
Release Notes
Contents
Pairing and removing the thermostat with ClareHome .................................... 5
Pairing and removing the thermostat in FusionPro ........................................ 10
Last modified:
11/18/20
Introduction
The Honeywell WiFi thermostats are a series of WiFi thermostats that have been
tested and certified for integration with the ClareHome system.
When integrating a Honeywell WiFi thermostat into your ClareHome project, no
extra connections are necessary. Install the thermostat according to the
Honeywell documentation, register the thermostat on the Honeywell portal,
enable auto mode in the thermostat, and then connect it to the network using IP.
All HVAC drivers share a common UI, so that the user experience is consistent.
Temperature settings can be controlled via events. Use F
usion’s Scenes and
Rules to automate the actions your customers want.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell RTH6580WF1001
Summary
DOC ID - 1188 • Rev 06.02 3 / 16 The Following figure shows the Honeywell controls on the ClareHome UI. Figure 1: User interface of the Honeywell thermostat (1) Temperature displays on the ClareHome UI in Fahrenheit. (2) Change the Heat set point by tapping the up/down arrow. (3) Change the Cool set...
DOC ID - 1188 • Rev 06.02 4 / 16 Registering the thermostat After installation, you must register the thermostat on the Honeywell portal. This allows the thermostat to be accessed remotely and updated with information from the Honeywell portal. To register the Honeywell thermostat: Note: To register...
DOC ID - 1188 • Rev 06.02 5 / 16 Pairing and removing the thermostat with ClareHome Follow the below steps to add and remove a thermostat in the ClareHome app. To pair the thermostat using ClareHome: 1. Tap the ClareHome app’s Devices page. 2. Tap Manage Devices .
