Electrolux 137064300A - Manual

5 MINIMUM INSTALLATION CLEARANCES - Inches (cm) SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Under- Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.54 cm) Installation Requirements Clearance requirements 0” (0cm) 0” (0cm) 1” (2.54cm) 0” (0cm) ...

6 Installation Requirements 38.00” (96.52cm) 53.00” (134.62cm) 50.6” (128.53cm)* to clear open door 31.50” (80.01cm)* to front of closed door water supply connection on rear of unit ¹ drain hose on rear of unit ² power cord on rear of unit ³ freestand washer on floor floor line floor line washer mou...

7 Unpacking Washer Removing foam packaging Temporarily remove door tape. 1. Open washer door and remove everything from 2. the drum.Close door and reapply door tape. 3. Using a rug, blanket or piece of cardboard to 4. protect the floor, carefully lay the washer on it’s back. Remove styrofoam base an...

8 Unpacking Washer Removing shipping hardware Installing hole plugs NOTE Rubber expansion material on spacers may need time to relax before they can be easily pulled through shipping hole. IMPORTANT Save all shipping bolts and spacers for future use. If the washer is to be transported at a later dat...

9 Installation Instructions raise lower Leveling your washer Excessive noise and vibration can be prevented by properly leveling the washer. For free standing installation and with the 1. washer within 4 feet (1 m) of its final location, place a level on top of the washer. Use the universal wrench t...

10 Run some water from the hot and cold faucets 1. to flush the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply.Look in the end of each water supply inlet hose 2. and verify that the rubber washers are in place. C...

11 Snap one end of the drain hose hanger 1. (shipped in washer drum) onto the drain hose. Continue wrapping it around the hanger and snap it in place.Place the hook end of the drain hose in the drain 2. opening. Secure the drain hose with the cable tie (provided in the enclosure package) to the stan...

12 If your washer has this console: If your washer has this console: Empty washer’s drum and close door. 1. After you plug in the washer the first time: wake up the washer by pressing any button, rotate cycle 2. knob to hand wash cycle, press the start button and then the cancel button. Wake up the ...

13 WARNING ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing could result in personal injury or even death. B) Removing Door from Hinge 1 Reopen door to 90 degree angle. 2 Remove 4 long, course-thread, counter-sunk hinge screws from door. A) Removing Trim Ring 1 Open the do...

15 Reversing Door E) Reattaching Door Lock to Front Panel 1 Rotate the door lock and move it to the opposite opening. 2 Connect the harness to the door lock by inserting it in the terminal and firmly pushing it in place. 4 Secure the lock with 2 short, course-thread, panhead screws. 3 Insert the har...

18 M) Reattaching Door Assembly 1 Open the hinge to a 90 degree angle. 2 Install the door onto the hinge locating pins. N) Reversing Trim Ring 1 Trim ring orientation is marked on the back. 2 Remove the trim ring cover plate. To remove the cover plate from the right, pivot point is up. To remove the...

19 If replacements parts are needed for your washer, contact the source where you purchased your washer, call 1-877-4ELECTROLUX (1-877-435-3287), or visit our website, www.electroluxappliances.com, for the Electrolux Authorized Parts Distributor nearest you. Options WARNING ELECTRICAL HAZARD Label a...