Crimestopper RS900/RS901 - Manual
Crimestopper RS900/RS901 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – parts in the vehicle.; DO NOT; result in damage to the unit not covered under warranty.; DO NOT
- Page 3 – WIRING INSTRUCTIONS
- Page 4 – rd IGN
- Page 6 – IGNITION SWITCH WIRING; IGN; OR; ACC; Heavy duty/High Current Ignition circuits
- Page 7 – POWER DOOR LOCK WIRING; +12V Coil Power for external relays TERM 86.; Single Wire Systems:; Plug-in pulse inverter that
- Page 8 – JUMPER PIN DIAGRAM
- Page 9 – IMPROVED “SMART TACHLESS” MODE; REDUCING “SMART TACHLESS” CRANKING TIME:; the brake once in place of pressing the lock button on the remote); Tach Reference Mode; These Tach Signal locations mentioned are provided as a
- Page 10 – TACH FINDER & TACH PROGRAMMING
- Page 11 – 00 IV TRANSMITTER / 999FM TRANSCEIVER CODE LEARNING; code and; WAIT FOR
- Page 12 – VEHICLE OPERATION; OPTION PROGRAMMING
- Page 14 – PROGRAMMABLE OPTIONS
- Page 15 – UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:
- Page 16 – RECEIVER; BATTERY; SERIES IV; JUMPERS
RS900/RS901
SERIES IV
RS999 FM FLASHBACK™
REMOTE ENGINE STARTING SYSTEM
INSTALLATION INSTRUCTIONS
PRE-INSTALLATION CONSIDERATIONS
To ease installation, we suggest that you READ THIS MANUAL and consider the following points before
beginning your installation:
BEFORE BEGINNING
, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,
ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).
PLAN OUT YOUR INSTALLATION
and determine most suitable locations for all components to be placed. These
components include: the module itself, valet/program button, possible relays, and antenna/receiver (RS900/999FM only,
RS901 model does not include antenna or remotes.) Allow enough wire to create a service loop with strain relief, should
servicing be required. This will also allow easier access and mounting.
DAMAGE
resulting from incorrect installation or failure to follow guidelines stated in this book will not be covered under
warranty and subject to repair or replacement charges.
USE A VOLT/OHM METER
to test and locate all connections. Test Lights can damage a vehicle’s computer systems.
ADDITIONAL PARTS
, which are not included with this unit, may be needed for your particular vehicle. . These items may
include extra relays (Part#CS-402A), General Motors Anti-Theft System Bypass modules for Vats / Passkey® / Passlock®
Systems, (Part# CS-GMATA II) or Transponder Anti-Theft Adapter modules (Part # CS-TATA).
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [email protected]
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV A - 8.2001
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modification could void the user’s authority to use the
equipment.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
TABLE OF CONTENTS Pre-Installation Considerations…………….………...……...………………………………………………………Front Cover Cautions & Warnings…….………………….………..…..………………………………………………………………………2 Wiring……..……………………………………………....……………………………………………………………….…….3-5 Ignition Switch Wiring………………….…..………………………………………………………………………….…………....
WIRING INSTRUCTIONS PROGRAM/OVERRIDE SWITCH: 2 PIN PLUG This switch is used for programming features, transmitters, valet mode, and to override the optional starter disable (if installed) in the event of a non-operating remote control. LED: 2 PIN PLUG The LED is used as a VALET/PROGRAMMING indicator...
WIRING INSTRUCTIONS PIN 4: YELLOW/BLACK FOR NEGATIVE IGNITION OUTPUT: YELLOW/BLACK 85 86 30 87 3rd IGN (If needed) IGN SW. OR ANTI-THEFT/ MODULE +12V CONSTANT OR TRANSPONDER PIN 4: YELLOW/BLACK: FOR ANTI-GRIND/STARTER DISABLE OUTPUT: (Relay not included) TO IGN 2 MOTOR ACC START CUT BROWN YELLOW/BLA...
