Crimestopper EZ-33DP - Manual
Crimestopper EZ-33DP – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – VENDORS
- Page 3 – USING THE REMOTE TRANSMITTER
- Page 4 – STATUS LED; REMOTE ENGINE CONTROL; REMOTE ENGINE STARTING - SUCCESSFUL START:; IGN; REMOTE ENGINE STARTING - UNSUCCESSFUL START; NO FURTHER
- Page 5 – TURNING OFF A REMOTE STARTED ENGINE:; now controlling your vehicle.
- Page 6 – SOLID; OFF; UNLOCK
- Page 7 – INDEFINITELY after the programmed run time elapses; INFINITY RUN MODE – EXITING THE VEHICLE:; THE
- Page 8 – SELECTABLE HOURLY COLD-START MODE – EXITING THE VEHICLE:
- Page 9 – should remain running for the selected number of minutes.
- Page 10 – CONVENIENCE AND SAFETY FEATURES
- Page 11 – VALET MODE / STARTER DISABLE OVERRIDE
- Page 12 – TRANSMITTER PROGRAMMING
- Page 13 – Press side button
- Page 14 – TROUBLESHOOTING: “BEFORE YOU CALL” SECTION; UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:
- Page 15 – run properly. The EZ; BATTERY REPLACEMENT; To replace the battery:
- Page 16 – REMOTE START DIAGNOSTICS
EZ-30DP/31DP/33DP/34DP
1-WAY SYSTEM
DP SERIES II (Data Port)
OPERATING INSTRUCTIONS
**IMPORTANT NOTES:- FOR EZ-30DP MODEL ONLY**
EZ-30DP Model is an add-on/expansion unit, without remotes or an antenna that must be controlled by an existing
alarm or keyless entry system. The “Infinity Run” feature is not available on an EZ-30DP system. Most of the
remote start features can be controlled through an existing factory or aftermarket remote keyless entry or alarm
system. Pressing an auxiliary button on an Aftermarket system or pressing a button 3 times on a Factory keyless
remote can activate a remote start using the EZ-30DP. This is referred to in this manual as activating the “Green
Start input wire”.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY:
These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, and Brake Reset. For programming, the hood pin and program button are
required.
-OPTIONAL:
These features are to be connected only if desired or agreed upon by the customer and the installing
dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features may also
require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be
installed with your particular system.
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV B - 07.2006
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Using the Remote Transmitter…………………………………………………………………………………...…….3 Status LED……………………………………………………………………………………………………………….4 Remote Engine Control…………….…..…………………………………………………………………….……….3-8 Turbo Timer Mode……………...
3 USING THE REMOTE TRANSMITTER EZ START #1 REMOTE VEHICLE 2 FLASHLIGHT START EZ START #1 #2 #3 LOCK REMOTE UNLOCK VEHICLE 2 FLASHLIGHT START EZ START #3 #1 #2 #4 LOCK TRUNK REMOTE UNLOCK VEHICLE 2 FLASHLIGHT START EZ-34DP II EZ-33DP II EZ-31DP II For EZ-30DP II The EZ-30DP II model does not include ...
4 STATUS LED LED Operation: (install option) LED will flash when remotely locking your doors. LED will remain solid in Valet Service mode. REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (*default). (For EZ-30DP II models, con...