Crimestopper CS-2003DC SERIES II - Manual
Crimestopper CS-2003DC SERIES II – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TABLE OF CONTENTS; Installation Cautions & Warnings.................................................................................................2; INSTALLATION CAUTIONS & WARNINGS; BEFORE BEGINNING; before jump starting, using a battery charger, or; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED; any other moving parts in the vehicle.
- Page 3 – CONTROL MODULE MOUNTING; DO NOT Mount the control unit in the engine compartment!; Driver’s Side Underdash; across from the driver’s side.; COMPONENT MOUNTING; Mount the red LED in a visible location on the dashboard or console.
- Page 4 – WIRING; PIN 1: GRAY WIRE: INPUT SOURCE FOR REMOTE OUTPUT 1 RELAY
- Page 5 – PIN 11: YELLOW WIRE: IGNITION SWITCHED “ON” +12 VOLTS INPUT; BLACK Wire: Sensor Ground; RED Wire Sensor +12V Power
- Page 6 – One wire dual voltage:
- Page 7 – SEPARATE DRIVER’S DOOR UNLOCK WIRING; NEGATIVE TRIGGER DOOR LOCKS
- Page 8 – TRANSMITTER PROGRAMMING; This system will learn a maximum of 3 transmitters total.; OR
- Page 9 – OPTION PROGRAMMING; PROGRAMMABLE OPTIONS; PROGRAMMING OPTIONS CHART
- Page 10 – Doors will not lock if; DOUBLE UNLOCK PULSE
- Page 11 – PARKING LIGHTS ON WITH DISARM; OPTION RESET (RESTORE TO DEFAULT VALUES)
- Page 12 – BUTTON REMOTE TRANSMITTER:
- Page 13 – OPERATING INSTRUCTIONS
- Page 15 – OPERATION; OPEN ZONE ALERT/BYPASS; Doors will not lock if they are open to prevent locking; VEHICLE OPERATION; VEHICLE CONTROL; CARJACK PROTECTION; ACTIVE CARJACK
- Page 16 – PASSIVE CARJACK
- Page 17 – SERIES II; This page applies to CS2003DC Series II systems ONLY:; BUTTON 1; *GREEN LED Blinks once for Bank 1 and twice for Bank 2.; “SUPER BRIGHT” BLUE LED /; LED POD
- Page 18 – DASH; Use
CS-2003DC & CS-2003DC Series II
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS
on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY:
These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., +12V Power, Ground, Doorpin, Override/Program/Valet Button etc.
-OPTIONAL:
These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Flashing Lights, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
Website: www.crimestopper.com
Email: [email protected]
REV. D 7/2002 SW: T2, SC, HC,
Latest: CH-(Green dot)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………………………2 Control Module Mounting………….……………………………………………..……………………….…………..3 Component Mounting………….…………………………………………………………….…………………..……..3 Wiring……..……………………………………………………………………………………………………….…….4-5 Power Door Lock Wiring...……...
CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed locati...
WIRING PIN 1: GRAY WIRE: INPUT SOURCE FOR REMOTE OUTPUT 1 RELAY Connect to a +12 Volt or Chassis Ground source depending on the output required for PIN 2 Gray wire See Below. PIN 2: GRAY WIRE: REMOTE OUTPUT 1 On-Board Relay (Optional) Connect this wire to an AUX device or Function. This output will ...
