Error Codes, Warranty, and Maintenance - Condtrol Vector 30 - User Manual - Page 2
Table of Contents:
- Page 1 – Safety, Specifications, and Basic Operations
- Page 2 – Error Codes, Warranty, and Maintenance
- Page 3 – Safety, Specifications, and Controls
- Page 4 – Error Codes, Care, and Warranty
- Page 5 – Safety, Specifications, and Calculations
- Page 6 – Maintenance, Error Codes, and Warranty
- Page 7 – Safety, Specifications, and Operations
- Page 8 – Error Codes, Maintenance, and Warranty
ERRORS
During operation, the following codes/symbols may appear on the display:
| Error code | Problem | Solution |
|---|---|---|
| 203 | Battery is too low. | Replace the batteries. |
| 402 | Calculation error. | Make measurement again. |
| 301 | Temperature is too high. | Cool down the device to operating temperature range. |
| 302 | Temperature is too low. | Warm up the device to operating temperature range. |
| 101 | Reflected signal is too weak. | Choose the surface with stronger reflectance. Use the reflecting plate. |
| 102 | Reflected signal is too strong. | Choose the surface with weaker reflectance. Use the reflecting plate. |
| 201 | Ambient light is too strong. | Make measurements in less illuminated zone. |
| 401 | Hardware error. | Switch on/off the device several times. If the symbol still appears, then the device may be defective. Contact the store where the device was purchased, or an authorized service center. |
UTILIZATION
Expired tools, accessories and package should be passed for waste recycle. Please send the device to the following address for proper recycle:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Do not throw the device in municipal waste!
According to European directive 2002/96/EC expired measuring tools and their components must be collected separately and submitted to environmentally friendly recycle of wastes.
WARRANTY
All CONDTROL GmbH devices go through post-production control and are governed by the following warranty terms. The buyer's right to claim about defects and general provisions of the current legislation do not expire.
1) CONDTROL GmbH agrees to eliminate all defects in the device, discovered during the warranty period, that represent the defect in material or workmanship in full volume and at its own expense.
2) The warranty period is 24 months and starts from the date of purchase by the end customer (see the original supporting document).
3) The warranty doesn't cover defects resulting from wear and tear or improper use, malfunction of the device caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of non-original accessories and spare parts. Modifications in design of the device relieve the seller from responsibility for warranty works. The warranty does not cover cosmetic damage, that doesn't hinder normal operation of the device.
4) CONDTROL GmbH reserves the right to decide on replacement or repair of the device.
5) Other claims not mentioned above, are not covered by the warranty.
6) After holding warranty works by CONDTROL GmbH warranty period is not renewed or extended.
7) CONDTROL GmbH is not liable for loss of profit or inconvenience associated with a defect of the device, the rental cost of alternative equipment for the period of repair.
This warranty applies to German law except provision of the United Nations Convention on contracts for the international sale of goods (CISG).
In warranty case please return the device to retail seller or send it with defect description to the following address:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires careful handling. The following recommendations will extend the life of the device:
- Do not point the device at the sun.
- Protect the device from bumps, falls, and excessive vibration; do not let liquids, construction dust and foreign objects get inside the device.
- Do not expose the device to extreme temperatures.
- If liquids get inside the device first remove the batteries, then contact the service center.
- Do not store or use the device under high humidity conditions for a long time.
- Clean the device with soft wet cloth.
- Keep device optics clean and protect it from mechanical damage.
- Carry out control measurements occasionally, especially if the device is subject to excessive mechanical or other impact, before and after taking important measurements.
Failure to observe the following rules may lead to leakage of electrolyte from the batteries and damage of the device:
- Remove the batteries from the device if it is not used for a long time.
- Do not use batteries of different types, with different charge level.
- Do not leave discharged batteries in the device.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Introduction to the device including safety regulations, intended use, technical specifications, delivery package, button functions, display indicators, battery installation, power on/off, reference point selection, measuring units, and measurement modes such as single distance and continuous tracking....
List of error codes with problems and solutions, utilization instructions for recycling, warranty terms covering 24 months with conditions and exclusions, and care and maintenance guidelines including cleaning and battery precautions.
Covers safety instructions, technical specifications, delivery scope, product description with button functions and display, battery installation, switching on/off, reference point selection, measuring units, and measurement modes including single and continuous measurements.
Tips
- Always use a target plate to improve measurement range in bright daylight or on low-reflectivity surfaces.
- Replace batteries as soon as error 203 appears to avoid inaccurate readings.
- Avoid measuring on transparent or glossy surfaces to prevent errors.
- Store the device in its case when not in use.
- Clean the optics with a soft cloth.
- If the device is not used for a long time, remove the batteries to prevent leakage.
- Perform control measurements periodically, especially after mechanical impacts.
- Do not disassemble the device; refer to authorized service centers for repairs.
