Chicago Electric 91814 - Manual
Chicago Electric 91814 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Troubleshooting section at end of manual.; Contents
- Page 3 – SPECIfICATIONS; DUTY CYCLE; at its rated load without overheating.; SAVE ThIS MANUAL; GENERAL SAfETY RULES; SAVE ThESE INSTRUCTIONS; WORk AREA; keep your work area clean and well lit.; Cluttered benches and dark areas invite
- Page 5 – “Inspection, Maintenance, And Cleaning”
- Page 6 – SPECIfIC SAfETY RULES
- Page 7 – Inhalation hazard; Welding Produces TOxIC fUMES and GASSES.; Exposure to welding gasses can increase the risk of developing; Avoid overexposure to fumes and gases.; always keep your head out of the fumes.
- Page 8 – Examine all hoses and cables for cuts,; Proper cylinder care.; secure cylinders to a cart, wall, or post, to prevent them from
- Page 9 – GROUNDING; ExTENSION CORDS; Grounded, 220 vaC tools require a three wire extension cord.
- Page 10 – SYMBOLOGY; UNPACkING
- Page 11 – ASSEMBLY INSTRUCTIONS; This plug must be installed by a qualified electrician.; CONTROLS AND INDICATORS
- Page 12 – OPERATING INSTRUCTIONS; SETUP; thoroughly
- Page 13 – CUTTING; Cutter indicator lights.
- Page 14 – PROPER CUTTING TEChNIqUE; Lightly touch the Tip to the cutting surface.; Must; BE MAINTAINED OR ThE UNIT; If the unit stops and the Red Overheat Indicator (4) lights:; Turn the power switch to oFF.; C. set the Torch handle down on the metal workbench,
- Page 15 – TORCh INSPECTION AND ASSEMBLY; Note: The Ceramic Ring only goes on one way. The Ceramic Ring
- Page 16 – CIRCUIT DIAGRAM; PLEASE READ ThE fOLLOWING CAREfULLY
- Page 17 – PARTS LIST; Parts referenced with * above are on this diagram.
- Page 18 – ASSEMBLY DIAGRAM
- Page 19 – TROUBLEShOOTING; fAN RUNS WhEN SWITChED ON BUT ARC WILL NOT IGNITE; b. The Regulator on the
- Page 22 – OR; ExCESSIVE SLAG fORMATION; b. The Regulator on the unit must be set
PLASMA AIR CUTTER
220 VOLT - 36 AMP
INVERTER TECHNOLOGY
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission oaks Blvd., CaMarillo, Ca 93011
VISIT OUR WEB SITE AT hTTP://WWW.hARBORfREIGhT.COM
Copyright
©
2004 by Harbor Freight Tools
®
. all rights reserved. no portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
for technical questions and replacement parts, please call 1-800-444-
91814
MANUAL REVISED 02/05; 06/06
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
for technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. skU 91814 PaGE 2 Contents SPECIfICATIONS ............................................................................ 3GENERAL SAfETY RULES ............................................................ 3SPE...
for technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. skU 91814 PaGE 3 SPECIfICATIONS Cutting depth 3/8 inch on steel Cutting Current 5 to 36 amps listed rated load voltage 100 vdC no-load voltage 200 vdC (maximum) Power Consumption 220 vaC, 15 amps, 50/60 Hz...
for technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. skU 91814 PaGE 5 13. Remove adjusting keys or wrenches before turning the power tool on. a wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. 14. Do n...
