Campbell Hausfeld GN0800 - Manual
Campbell Hausfeld GN0800 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DANGER; WARNING; General Safety
- Page 3 – CAUTION; EXTENSION CORDS; Operation
- Page 4 – Maintenance; MAINTENANCE SCHEDULE
- Page 5 – Troubleshooting Chart
- Page 6 – Limited Warranty
- Page 7 – Geradores Portáteis; Descrição; AVISO
- Page 8 – PERIGO; Segurança geral; Operação
- Page 9 – CUIDADO; Manutenção
- Page 10 – PROGRAMA DE MANUTEÇÃO
- Page 11 – Tabela para Pesquisa de Avarias
- Page 13 – Notas
- Page 14 – Generadores portátiles; Descripcíon; ADVERTENCIA
- Page 15 – PELIGRO; Medidas de Seguridad; Funcionamiento
- Page 16 – CORDONES DE EXTENSION; PRECAUCION; Mantenimiento
- Page 17 – PLANIFICACIÓN DE MANTENIMIENTO
- Page 18 – Guía de Diagnóstico de Averías
9. Keep all persons away from parts
that move or become hot during
operation.
10. Be sure all powered devices are shut
off prior to connecting them to the
generator.
11. Keep the generator clean and well
maintained at all times.
Never operate this
generator in an
explosive atmosphere
or poorly ventilated
area.
!
WARNING
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN284700AV 9/02
Operating Instructions
Models GN0950 and GN0800
Portable Generators
B U I L T T O L A S T
This generator is powered by an air-
cooled two-cycle engine. It is designed
to run at maximum RPM and give a
continuous wattage as rated.
When unpacking, inspect carefully for
any damage that may have occurred
during transit. Make sure any loose
fittings, bolts, etc., are tightened before
putting unit into service.
1. Before starting or
servicing any
generator, read and
understand all
instructions. Failure
to follow safety
precautions or instructions can cause
equipment damage and/or serious
personal injury. Retain all manuals
for future reference.
2. Never use this generator for any
application other than that specified
by the manufacturer. Never operate
this generator under conditions not
approved by the manufacturer.
Never attempt to modify this
generator to perform in any manner
not intended by the manufacturer.
3. For maintenance and repairs, use
only products and parts
recommended by the manufacturer.
4. Be sure that the generator is
properly grounded to an external
ground path prior to operation.
Refer to the section entitled
“Grounding Instructions” for proper
grounding procedures.
5. Be sure that the generator is
operated only by persons who have
read and understand these
instructions.
6. Be sure that the generator is placed
on a flat level surface prior to and
during operation. The generator
must not slide or shift during
operation.
7. Keep all persons away from the
generator during operation.
8. Do not allow persons wearing loose
clothing or jewelry to start or
operate the generator. Loose
clothing or jewelry may become
entangled in moving components,
causing equipment damage and or
personal injury.
MANUAL
Fig. 1 - Assembled Units GN0950 and GN0800
© 2002 Campbell Hausfeld / Scott Fetzer
Description
Unpacking
General Safety
See Warranty on page 6 for important information about commercial use of this product.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
A Ground Fault Circuit Interrupter may not be effective if used on agenerator that is not grounded! 3. When installing a GFCI, be sure to follow all national and localregulations, or call a licensed orcertified electrical technician. GROUNDING 1. Use the ground terminal on thegenerator frameto conne...
3 GN0950 and GN0800 4. Move the choke/run switch to the chokeposition. 5. Turn engine switch on by pressing thetop of the switch. 6. Pull the starter rope with a brisk smoothmotion. 7. Return choke/run switch to the run position. 8. After each start up, allow engine to run 2-3 minutes with no load. ...
4 Operating Instructions compression cycle, and the intakeand exhaust valves are closed. (Thepiston pushes a small amount of airfrom the spark plug hole oncompression). 6. To clean air filter – Remove filterfrom generator. Wash in a solvent.Pour motor oil(SAE #20)on filter,squeezeout excessand reins...
