Campbell Hausfeld WG2020 - Manual

Campbell Hausfeld WG2020

Campbell Hausfeld WG2020 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
Page: / 36

Table of Contents:

  • Page 2 – Wire Feed Arc Welder; Spread out coiled welding cable; General Safety
  • Page 3 – Safety and Health Standards; ADDITIONAL SAFETY STANDARDS
  • Page 4 – Assembly; Installation
  • Page 5 – Contact Tip Markings; Shielding Gas Preparation; Torch
  • Page 6 – HOOKUP PROCEDURE; Operation; Metal; Maintenance; Consumable and Wear Parts
  • Page 7 – Welding Guidelines; Supply Cable Replacement; Verify that welder is OFF and power cord disconnected.; General
  • Page 8 – WELD ANGLE; TRAVEL ANGLE
  • Page 9 – the puddle across the
  • Page 10 – Troubleshooting Chart - Welds
  • Page 11 – For Information About
  • Page 12 – Glossary of Welding Terms
  • Page 13 – Déballage; dans une prise de courant de 115 V.; Need; Pince de soudeur - s’attache à l’objet; ATTENTION; Description; EXIGENCES DE CIRCUIT
  • Page 14 – Soudeur à l’Arc Alimenté en Fil; DANGER
  • Page 15 – et les tenir en bon état de marche.; b. S’assurer que l’endroit de soudage
  • Page 16 – AVERTISSEMENT; ENDROIT; Montage; MONTAGE DE MANCHE ET BASE
  • Page 17 – Marques De Pointe De Contact
  • Page 18 – REMARQUE; Épaisseur Rélage de; Entretien
  • Page 19 – Directives De Soudage; Généralités; RÉGLAGE DE CHALEUR
  • Page 20 – VITESSE DE FIL; ANGLE DE DÉPLACEMENT
  • Page 21 – POUSSER; la flaque à travers de; tirer
  • Page 22 – Guide de Dépannage - Soudeur; Pour des informations concernant ce produit,
  • Page 23 – Pour de l’information
  • Page 24 – Lexique de Termes de Soudage
  • Page 25 – Abrazadera de trabajo – conéctela a; Desempaque; PRECAUCION; Descripción; REQUERIMIENTOS DEL CIRCUITO; Seguridad General
  • Page 26 – Soldadora Por Arco Con Alimentación de Cable; PELIGRO
  • Page 27 – b. Asegúrese de que el área de; UBICACIÓN; Instalación
  • Page 28 – ADVERTENCIA; Ensamblaje; ENSAMBLAJE DEL ASA Y LA BASE
  • Page 29 – Marcas de la punta de contacto; Preparación del gas protector; TIPOS DE GAS; POLARIDAD
  • Page 30 – Operación; Espesor Ajuste; Mantenimiento; ANTES DE CADA USO; PROCEDIMIENTO DE CONEXIÓN (
  • Page 31 – Pautas de Soldadura; Cambio del cable de alimentación; Información general; AJUSTE DEL CALOR
  • Page 32 – VELOCIDAD DEL CABLE; ÁNGULO DE PROPAGACIÓN
  • Page 33 – EMPUJE
  • Page 34 – Table de Detección y Solución de Problemas - soldadora
  • Page 35 – Para información acerca de
  • Page 36 – Glosario de Términos de Soldadura
Loading the manual

Heat

Circuit Breaker or

Selector

Slow Blow Fuse

Low 15

amp

High 20

amp

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.

IN212800AV 7/99

Operating Instructions & Parts Manual

Model WG2020

Wire Feed
Arc Welder

B U I L T T O L A S T

TM

The Campbell Hausfeld WG2020 is a 70
amp, single phase 115 volt input, wire
feed arc welding machine equipped
with infinite wire speed control to
accurately select proper wire feed rate
needed for various welding conditions.
Internal components are
thermostatically protected.

This welding system is designed for use
with the Flux Core Arc Welding (FCAW)
or the Gas Metal Arc Welding (GMAW)
process. As delivered from the factory,
this welder can weld with .024” (.6mm)
to .035” (.9mm) diameter wire. A starter
spool of flux-cored wire is included.

1

2

4

5

6

3

1. Work Clamp - connect to work piece.

2. Wire Feed Gun

3. Power Cord - plug into 115 volt

outlet.

4. On/Off Switch - illuminates if

thermostat has automatically shut
unit off.

5. Infinite Wire Speed Control - turns

clockwise to increase wire speed and
counterclockwise to decrease wire
speed.

6. Heat Selector - Selects welding

power. Four selections are possible;
low 1, low 2, high 1 and high 2.

Danger means a
hazard that will

cause death or serious injury if the
warning is ignored.

Warning means a
hazard that could

cause death or serious injury if the
warning is ignored.

Caution means a
hazard that may

cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.

NOTE:

Note means any additional

information pertaining to the product
or its proper usage.

Figure 1 -
Welder Components
and Controls

See page 7 for supply cable
replacement instructions.

Q

UA

LIT

Y

A

SSURANCE

P

ROG

RA

M

Need

Assistance?

Call Us First!

1-800-746-5641

Unpacking

All welding accessories for the
welder are inside the wire feed
compartment. Lift and remove wire
feed cover to find handle,
workclamp, etc.

When unpacking,

inspect carefully for any damage that may
have occurred during transit. Make sure
any loose fittings and screws, etc. are
tightened before putting unit into service.

This equipment
requires a dedicated

115 volt circuit. Refer to the following
chart for correct circuit breaker or fuse
rating. Do not run other appliances, lights
or tools on this circuit while operating
this equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure to
comply with this recommendation.

Description

CIRCUIT REQUIREMENTS

COMPONENTS AND CONTROLS

General Safety

For parts, product & service information

visit

www.campbellhausfeld.com

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Wire Feed Arc Welder; Spread out coiled welding cable; General Safety

2 Wire Feed Arc Welder Always keep a fireextinguisher accessiblewhile performing arcwelding operations. ● Before starting orservicing any electricarc welder, read andunderstand allinstructions. Failureto follow safetyprecautions or instructions can causeequipment damage and/or seriouspersonal injury...

Page 3 - Safety and Health Standards; ADDITIONAL SAFETY STANDARDS

welder in areas where flammable orexplosive vapors may be present. ● Take precautions to ensure flyingsparks and heat do not cause flamesin hidden areas, cracks, etc. Fire hazard! Do notweld on containers or pipes that contain or have containedflammable materials or gaseous or liquidcombustibles. Ar...

Page 4 - Assembly; Installation

1. Loosen hex bolt on work clamp. 2. Insert cord (labeled work on the front panel of the welder) throughclamp handle and slide bare wireunder the clamp block. Tighten hexbolt making sure bare wire isclamped securely (Figure 3). Welding powermay be applied to output terminals, feed roll, work clamp,g...

Other Campbell Hausfeld Models

All Campbell Hausfeld Other