Campbell Hausfeld WF2010 - Manual
Campbell Hausfeld WF2010 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DANGER; General Safety
- Page 3 – Work Clamp; WARNING
- Page 4 – Flux Core Wire Installation; Do not cut; Turn; CAUTION; Contact Tip Markings; Operation
- Page 5 – Consumable and Wear Parts; for replacement parts; General; HEAT SETTING
- Page 6 – Wire Feed Arc Welder; Welding Guidelines; TRAVEL ANGLE
- Page 7 – PUSH VS PULL TECHNIQUE; Supply Cable Replacement
- Page 8 – Troubleshooting Chart - Welder; Troubleshooting Chart - Welds
- Page 11 – Glossary of Welding Terms
- Page 12 – Notes
- Page 13 – Sélecteur de chaleur; AVERTISSEMENT; Instructions D’Utilisation & Manuel De Pièces De Rechange; Déballage; ATTENTION; Collier de mise à la terre; Sélecteur; Description; Généralités Sur La Sécurité
- Page 14 – Soudeur À L’Arc Alimenté En Fil; REMARQUE
- Page 15 – Retirer les tiges à chaque extrémité; a. Enlever l’enduit du métal; Installation
- Page 16 – Montage; Marques De Pointe De Contacte; Fonctionnement
- Page 17 – Pièces Consommables Et Qui; Généralités; RÉGLAGE DE CHALEUR; Épaisseur; Directives De Soudage
- Page 18 – ANGLE DE DÉPLACEMENT
- Page 19 – la flaque à; tirer; POUSSER; Débrancher le fil vert du cordon; Remplacement du cordon d’alimentation électrique
- Page 20 – Guide de dépannage - Soudeur; Guide de dépannage - Soudures
- Page 21 – Schéma d'installation de fils WF2010
- Page 23 – Lexique de Termes de Soudage
- Page 25 – Manual de Instrucciones y Lista de Repuestos; Para desempacar; Componentes y Controles; Pinza; PRECAUCION; ADVERTENCIA; PELIGRO; Descripción
- Page 26 – Ésto le indica cualquier; Soldadora Con Arco Con Alambre Continuo
- Page 27 – b. Cerciórese de que el área de; Safety and Health Standards; —NFPA; Instalación
- Page 28 – No corte el alambre todavía; Abrazadera de Trabajo; INSTALACION DEL ALAMBRE; mm; Funcionamiento; Ensamblaje
- Page 29 – Comuníquese con el; Espesor
- Page 30 – Instrucciones para Soldar; ANGULO DE DESPLAZAMIENTO
- Page 32 – DIAGNOSTICO; Diagóstico de Averías-Soldadora; Diagóstico de Averías-Soldadura
- Page 34 – Para ordenar repuestos, comuníquese con el distribuidor
- Page 35 – Glosario de terminología usada por soldadores
- Page 36 – Notas
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN211702AV 11/00
Operating Instructions & Parts Manual
Model WF2010
Wire Feed
Arc Welder
The Campbell Hausfeld WF2010 is a 70
amp, single phase 115 volt input, wire
feed arc welding machine equipped with
infinite wire speed control to accurately
select the proper wire feed rate needed
for various welding conditions. Internal
components are thermostatically
protected.
This welding system is designed for use
with Flux Core Arc Welding (Gasless)
only. As delivered from the factory, this
welder can weld with .030” (.8mm) to
.035” (.9mm) diameter flux-cored wire.
A starter spool of .035” flux-cored wire
is included.
Unpacking
Some welder components may be
found in the wire feed compartment.
When unpacking, inspect carefully for
any damage that may have occurred
during transit. Report any damaged or
missing items by calling (800) 746-5641.
Circuit Requirements
This equipment
requires a
dedicated 115 volt circuit. Refer to the
following chart for the correct circuit
breaker or fuse rating. Do not run
other appliances, lights, or tools on
this circuit while operating this
equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure
to comply with this recommendation.
!
CAUTION
Components and Controls
1.
Work Clamp
- connect to work
piece.
2.
Wire Feed Gun
3.
Power Cord
- plug into 115 volt
outlet.
4.
On/Off Switch
5.
Heat Selector
- Selects welding
power (high/low).
6.
Infinite Wire Speed Control
-
turn clockwise to increase wire
speed and counterclockwise to
decrease wire speed.
Heat
Circuit Breaker or
Selector
Slow Blow Fuse
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
NOTE:
Note means any additional
information pertaining to the product
or its proper usage.
!
CAUTION
!
WARNING
!
DANGER
Low 15
amp
High 20
amp
Q
U
A
L
IT
Y
AS
S
U
RANC
E
P
ROG
RA
M
Need
Assistance?
Call Us First!
1-800-746-5641
Description
General Safety
2
1
3
4
5
6
Figure 1
© 2000 Campbell Hausfeld / Scott Fetzer
For parts, product & service information
visit
www.chpower.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Wire Feed Arc Welder Always keep a fireextinguisher accessiblewhile performing arcwelding operations. ● Before starting or servicing anyelectric arc welder, read andunderstand all instructions. Failureto follow safety precautions orinstructions can cause equipmentdamage and/or serious personalinju...
LOCATION Selecting the proper location cansignificantly increase performance,reliability and life of the arc welder. ● For best results locate the welder inan environment that is clean anddry. ● Store flux core wire in a clean, drylocation with low humidity topreserve the flux wire coating. ● The us...
Flux Core Wire Installation Welding poweris applied to the output terminals, feed roll, work clamp,gun cable connection and welding wireeven when the the gun switch is notactivated. Do not touch these partswhen the welding machine is on. NOTE: Before installing welding wire, be sure that the diamete...
