Thermo Pride GMC-85 - Manuals

All installations and services must be performed by qualified service personnel. 9 III. FURNACE SPECIFICATIONS MODEL OMC-70 GMC-85 HEAT INPUT RATE (BTUH) 85,000 85,000 HEATING CAPACITY (BTUH) 71,000 69,700 BURNER NOZZLE (GPH X ANGLE, HOLLOW CONE) 0.65X80A ------- BURNER ORIFICE-NAT. GAS --------- #1...

All installations and services must be performed by qualified service personnel. 10 BURNER DATA OMC-70 GMC-85 MANUFACTURER: R.W. BECKETT CORP. WAYNE COMBUSTION SYSTEMS MODEL: AFG P265 FEP AIR TUBE LENGTH (IN.): 3-5/8 3-5/8 HEAD DESIGN: F-3 -------- REFRACTORY TYPE: MHC (FIBER) MHC (FIBER) OIL PUMP P...

All installations and services must be performed by qualified service personnel. 11 IV. INSTALLATION A. ROOF JACK The roof jack assembly and accessories must be listed by a nationally recognized testing agency for the appropriate fuel. The roof jack assembly must be installed according to the vent m...

All installations and services must be performed by qualified service personnel. 13 Figure 1B. D. BASE INSTALLATION 1. Combustible Floor Base Model: 70-BASE Referring to Figure 1A, for applications using a combustion air channel and a supply air duct, use the base as a template to mark the floor ope...

All installations and services must be performed by qualified service personnel. 14 If the combustion air passageway cannot terminate outside of the skirting or enclosure, a permanent opening with a minimum of 50 square inches of unobstructed infiltration (free area) for ventilation air must be prov...

All installations and services must be performed by qualified service personnel. 16 E. ALCOVE INSTALLATION In this application, a minimum of 18 inches of clearance must be provided to the front of the unit. Refer to Figure 4. Alcove installations must use the No. 70 mobile home base. Refer to sectio...

All installations and services must be performed by qualified service personnel. 21 : The furnace and its gas valve must be disconnected from the gas supply during pressure testing of the gas supply system at pressures in excess of 1/2 PSIG (13.9 inches W.G.). The furnace can be isolated from the ga...

All installations and services must be performed by qualified service personnel. 25 Once the furnace is installed, check the thermostat anticipator the proper nominal setting. a. Connect a multimeter, capable of reading milliamps (mA), in series with the low voltage wires to the thermostat. b. Incre...

All installations and services must be performed by qualified service personnel. 26 4. WIRING DIAGRAM

All installations and services must be performed by qualified service personnel. 30 The temperature rise across the furnace heat exchanger operating at steady-state conditions (about 15 to 20 minutes) should not exceed 100°F. The normal comfort range is between 70°F to 100°F. A lower temperature ris...

All installations and services must be performed by qualified service personnel. 31 V. DEALER MAINTENANCE THIS SECTION IS ONLY TO BE PERFORMED BY TRAINED, QUALIFIED SERVICE PERSONNEL, AND NOT BY THE FURNACE OWNER. A. TROUBLESHOOTING : When testing electrical equipment, always follow standard electri...

All installations and services must be performed by qualified service personnel. 32 Yes Set thermostat subbase to "HEAT" Does thermostat make contact? Does a "call for heat" initiate an ignition cycle? No Yes Is room temperature above 90 deg. F? Yes Wait for room air to cool. Yes Tur...

All installations and services must be performed by qualified service personnel. 38 C. HEAT EXCHANGER CLEANING INSTRUCTIONS : The heat exchanger must be cleaned by a qualified service person. For oil-fired units, it is important to inspect and clean the heat exchanger once a year, or as necessary, t...

All installations and services must be performed by qualified service personnel. 40 Check all flue pipes for restrictions due to soot, or carbon build-up, as well as foreign matter, or any materials, that cause the venting system to restrict the proper venting of combustion products. If a restrictio...

All installations and services must be performed by qualified service personnel. 41 VI. USER INFORMATION SECTION A. WARNINGS AND CAUTIONS: : If you suspect there is a problem with the furnace, pertaining to the venting system or any other related problem, immediately contact a qualified service agen...