Teledyne IGE 3000 - Manuals

IGE 300 Page 6 of 21 2. General Information 2.1. GENERAL INFORMATION The Teledyne Hastings Instruments IGE-3000 is a small, fully self contained ion gauge electronics module. The mini- Bayard Alpert style ion gauge tube is attached to the electronics module by a 12 pin circular connector. The IGE-30...

IGE 300 Page 7 of 21 2.4. Materials exposed to Vacuum • Yttia coated Iridium • Nickel • 304 Stainless Steel • Glass • Tungsten • Platinum Clad Molybdenum

IGE 300 Page 9 of 21 3.5. “D” Connector Electrical Pin outs The figure below indicates all pin outs. FIGURE 1- IGE-3000 “D” CONNECTOR NOTE: Set Point High, Set Point Low and Remote Start, use Digital ground Pin 8 as signal return path. 3.6. B/A Tube Installation The Bayard/Alpert (B/A) tube may be i...

IGE 300 Page 10 of 21 4. Operation 4.1. Operation 4.1.1. Apply Power Apply 24 VDC Power to the “D” connector pin 3 and 4. (Refer to Section 2.5 /Figure 1, for the “D” connector pin out information). After power is applied the IGE-3000 will go through self test, CPU initialization, and LED test. (The...

IGE 300 Page 11 of 21 4.2.1. SELECT SELECT is a push-button. Pressing it will scroll through the different available operating modes. Rapidly “double clicking” SELECT will either turn the selected filament on (if unit is off) or off (if the unit is on) Note: Ensure vacuum is below 1x10-2 Torr. The I...

IGE 300 Page 12 of 21 4.3.3. DGas Mode: CAUTION: BEFORE INITIATING DEGAS, VACUUM MUST BE AT OR BELOW 1x10-7 EXCESSIVE DEGASSING AT ANY TIME CAN DISTORT THE GAUGE ELECTRODES AND CAN RESULT IN A MISLEADING TRANSIENT DECREASE IN PRESSURE INDICATION Degas mode is used to “Degas” or clean the inside area...

IGE 300 Page 13 of 21 The IGE-3000’s filament may be controlled remotely via the D power supply connector by wiring relay contacts or a transistor switch across pins 8 and 9, (refer to section 2.5 /Figure 1 and Figure 3 below). Pin 8 is digital ground and pin 9 is the filament control line. The IGE ...

IGE 300 Page 14 of 21 5. Theory of Operation The functional parts of a typical ionization gauge tube are the filament (cathode), the grid (anode), and the ion collector (refer to Figure 4 below). The IGE-3000 control circuit maintains the grid voltage is maintained at 30 VDC, the grid voltage is mai...

IGE 300 Page 15 of 21 6. Set Up Guide 6.1. ADVANCE SETUP GUIDE The IGE-3000 has several setup and control commands which can be accessed by using the ADJUST rotary encoder and SELECT push-button while viewing the display. Note that most of the commands, which are described below, can be accessed usi...

IGE 300 Page 16 of 21 6.4. Data Bits/Parity Bits/Stop Bits P8n1 The first character, “8” corresponds to the number of data bits. (e.g. 7 or 8). Second character, “n” corresponds to the parity bit. (i.e. n- no parity, E- even parity, o- odd parity, 0- space, 1- mark) The last character, “1” correspon...

IGE 300 Page 18 of 21 8. Device Status 8.1. ION GAUGE DEVICE STATUS: 4-DIGIT OCTAL WORD When requested to transmit its status the IGE-3000 responds with a 4-digit octal word. FIGURE 7 -1 – DIGIT OCTAL WORD • bit 11: Serial Receiver Overload • bit 10: Main Board EEPROM Error. • bit 9: Communication S...

IGE 300 Page 19 of 21 • When entering more than one command in the same data string, they must be separated by a comma. • All command strings must be followed by the terminator character (carriage return <CR>, also known as ENTER). • When a lower case character is present in an example it repr...

IGE 300 Page 20 of 21 9. WARRANTY 9.1. Warranty Repair Policy Hastings Instruments warrants this product for a period of one year from the date of shipment to be free from defects in material and workmanship. This warranty does not apply to defects or failures resulting from unauthorized modificatio...