Star Trac V-bike Spinner Spinner Pro Spinner Elite Spinner NXT - Manuals

Page 2 - ABLE OF; WARNING

Page 2 STAR TRAC GROUP CYCLES OWNER’S GUIDE T ABLE OF C ONTENTS _ Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions . . . . . . . . . . . . . . . . . . ...

Page 3 - AFETY; NSTRUCTIONS; FITNESS SAFEGUARDS; OPERATING PRECAUTIONS

Page 3 STAR TRAC GROUP CYCLES OWNER’S GUIDE S AFETY I NSTRUCTIONS _ I NSTRUCTIONS The following fitness safeguards and operating precautions are directed to purchasers and users of STAR TRAC group cycles. Club Managers should ensure that members and fitness staff are trained to follow these same ins...

Page 4 - SSEMBLY AND; SPINNER; NPACKING; Assembly; Description; Spare Parts Kit

Page 4 STAR TRAC GROUP CYCLES OWNER’S GUIDE A SSEMBLY AND S ETUP _ A SSEMBLY AND S ETUP V-BIKE ® SPINNER ® ASSEMBLY AND SETUP Use the following procedures to unpack and assemble your STAR TRAC V-BIKE SPINNER . U NPACKING Position the shipping carton so the “Heavy End” logo is located at the bottom. ...

Page 5 - ASSEMBLY; Install the Back Leg; Step 3; Step 4

Page 5 STAR TRAC GROUP CYCLES OWNER’S GUIDE ASSEMBLY 1. Install the Back Leg Place the back leg in position at the rear of the cycle, aligning the two holes in the leg with the mating holes in the frame bracket. Insert two 8mm x 70mm bolts through the frame bracket and back leg, and install a flat w...

Page 6 - Install the Handlebar; Step 5

Page 6 STAR TRAC GROUP CYCLES OWNER’S GUIDE 5. Install the Handlebar Insert the handlebar post into the frame assembly and secure in place using a tension handle. Position the handlebar on top of the handlebar post and secure in place using a tension handle and washer. NOTE: Tighten the tension hand...

Page 9 - Install the Front Leg

Page 9 STAR TRAC GROUP CYCLES OWNER’S GUIDE ASSEMBLY Following these steps in order will minimize the build time and ensure proper assembly. Note: Not all of the following procedures are performed on all models; Spinner ® Pro, Elite and NXT. If the procedure is specific to a model it will be noted a...

Page 10 - Install the Pedals

Page 10 STAR TRAC GROUP CYCLES OWNER’S GUIDE Pro & Elite Only Using the 5mm hex wrench and a 13mm combination wrench insert 2- M10X55mm flat head screws, nuts and washers to secure the front leg assembly to the frame. Tighten all screws/nuts securely using a torque wrench to 85 Inch Pounds Step ...

Page 13 - NSTRUCTIONS FOR; Spinner NXT

Page 13 STAR TRAC GROUP CYCLES OWNER’S GUIDE I NSTRUCTIONS FOR U SE _ Your STAR TRAC group cycle is easy to use. Simply sit on the cycle, tighten the pedal straps and begin pedaling. The cycle allows the user full control over resistance by simply adjusting the brake pad. Typically, lower resistance...

Page 14 - HANDLEBAR ADJUSTMENTS; PEDAL STRAP ADJUSTMENT

Page 14 STAR TRAC GROUP CYCLES OWNER’S GUIDE HANDLEBAR ADJUSTMENTS Proper position for the handlebar is based primarily on comfort. Typically, the handlebar should be positioned slightly higher than the seat. All group cycles allow for adjustment of handlebar height. Additionally, the V-bike ® Spinn...

Page 15 - SMART RELEASETM SYSTEM; RAINING

Page 15 STAR TRAC GROUP CYCLES OWNER’S GUIDE SMART RELEASE™ SYSTEM (Spinner ® Elite) Allows the benefits of the direct drive system with a safety clutch to release the crank from the direct drive when a force is applied to the pedals. T RAINING I NFORMATION _ This section provides hints on how to st...

Page 16 - AINTENANCE; AINTENA; NCE; OOLS; AILY

Page 16 STAR TRAC GROUP CYCLES OWNER’S GUIDE M AINTENANCE _ This section provides the procedures to maintain the group cycles in serviceable condition. Differences between models are noted where applicable. MOVING AND LEVELING To move the cycle to a new location: Lift the cycle from the rear and use...

Page 17 - EEKLY

Page 17 STAR TRAC GROUP CYCLES OWNER’S GUIDE Inspection / Adjustment Inspect major moving parts that require constant proper torque. Loose or misadjusted parts can result in personal injury or damage to the cycle. Check the following parts for security and/or proper torque. Crank arms Use a foot pou...

Page 18 - Drive Chain Lubrication; ONTH; Spinner Elite; HAIN; Diagram A

Page 18 STAR TRAC GROUP CYCLES OWNER’S GUIDE Drive Chain Lubrication The drive chain will require lubrication once a month, or after every 100 hours of use. The chain should be lubricated with a light oil (preferably a lubricant that comes with a spray hose that fits in front of the can) and a dry c...

Page 19 - Diagram B; RAKE; Removal; Diagram C; Diagram

Page 19 STAR TRAC GROUP CYCLES OWNER’S GUIDE 3. Tighten the two bolts that go through the frame, moving the flywheel forward by turning clockwise, until there is approximately 3/16” of slack in the chain (Diagram B). 4. Re-tighten the two bolts on the sides of the flywheel and replace the chain shro...