Star Trac E-TBTe - Manuals

Star Trac E-TBTe – Manual in PDF format online.

Manuals:

Manual

Manual Star Trac E-TBTe

Summary

Page 2 - Adhere to all torque and assembly specifications.; FACTORY CERTIFIED INSTALLER

3 620-7921 Rev A GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual; the manual describes equipment setup and instructs members on how to use it correctly and safely. 1. Phillips screwdriver, #2 (Included) 2. Hex (Allen) key, 3/...

Page 3 - UNPACKING INSTRUCTIONS

4 620-7921 Rev A Step 1. Lay the box with heavy end facing down in the area where it is going to be assembled. Cut and remove packaging straps then open and remove the top cover. Step 2. Lift and remove the box from the pallet base. Step 3. Lift the unit off of the pallet base, then remove all packa...

Page 4 - Verify the following tools are included in the kit:; Verify the following hardware is included in the kit:

5 620-7921 Rev A Step 5. Remove remaining packaging ma-terials and lay all components on the floor. Step 6. Verify the following components are included in the package: 1. TBT frame. 2. Display console assembly. 3. Upper neck. 4. Left and right upper body arms. 5. Owner’s manual, installation manual...

Page 5 - INSTALLATION INSTRUCTIONS

6 620-7921 Rev A Step 1. Route display cables up through upper half of neck through the holes provided. Step 2. Insert the upper half of the neck into the lower half. Caution: Be careful not to pinch any cables between the two sections of the assembled neck. Step 3. Install two 5/16” - 18 X 3/4” but...

Page 7 - If the unit is not equipped with Personal View-

8 620-7921 Rev A Step 9. Identify the four cables coming out of the neck and mounting bracket: 1. Heart rate cable 2. Main I/O cable 3. Coax cable 4. DC power cable Note: If the unit is not equipped with Personal View- ing Screen, the coax and DC power cables should be tucked down the neck as they a...

Page 8 - Be careful not to pinch any wires.

9 620-7921 Rev A Step 13. Assemble the front and back display parts to-gether by sliding the bottom of the front display under the 2 tabs at the base first, then pressing front display against the back cover. Caution: Be careful not to pinch any wires. Step 14. Using provided Phillips head screw dri...

Page 9 - Refer to the User’s Manual for other settings; YOU HAVE NOW COMPLETED THE TOTAL BODY TRAINER INSTALLATION

10 620-7921 Rev A Step 17. Place the Total Body Trainer on the floor in the position it will be used. Then adjust leveling feet to assure that the Total Body Trainer is lev-eled to the floor and does not rock back and forth. YOU HAVE NOW COMPLETED THE INSTALLATION OF YOUR TOTAL BODY TRAINER Step 18....

Page 10 - ATTENTION

11 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the Total Body Trainer. • As with any moto...

Page 11 - non-scratching surface; to; EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS; Verify the tool kit has the following parts:; Assembly instructions

12 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. Embedded display console. 2. Operation manual. 3. Tool kit. 4. Power adaptor (60W AC). 5. Power cord. Step 3. Be careful with the display and place it face down on top of a non-scratchin...

Page 16 - YOU HAVE NOW COMPLETED THE EMBEDDED DISPLAY INSTALLATION

17 620-7921 Rev A Step 21. Now it is time to connect entertainment cable and power to the unit. Connect the in-house entertainment cable to the RF input at the base of the unit. Take the power supply from the kit and plug the small barrel connector to the DC input. Then take the power adapter cable ...

Page 17 - Calibration and Setup.

18 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the Total Body Trainer. • As with any moto...

Page 18 - iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS

19 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. iPod® center console. 2. iPod® cradle. 3. Owner’s manual. 4. Cable kit. 5. Lower back cover. Note: If the center console is being installed on a new unit, then perform this installation ...

Page 20 - Retain screws for later use.

21 620-7921 Rev A Step 9. Using a #2 Phillips head screwdriver, remove the (4) screws that hold bottom side of the dis-play console on, then remove the (1) screw that holds the headphone jack cap. Note: Retain screws for later use. Step 10. Next remove the bottom cover, then remove the headphone bla...

Page 23 - Before

24 620-7921 Rev A Step 23. Install the CSAFE power connector on the new bottom plastic cover. Step 24. Install the new bottom plastic cover onto display, use the screws saved from the earlier step to secure the display bottom. Tighten the screws so they are snug. Note: Take special care to not pinch...

Page 24 - The coax and DC power cables are part of the

25 620-7921 Rev A Step 26. Take the front display plastics with the new cen-ter console to the base unit. Hold the front dis-play plastics at the top with one hand while con-necting the cables and harnesses with the other. Step 27. Identify the four cables coming out of the neck and mounting bracket...

Page 26 - YOU HAVE NOW COMPLETED THE iPod® CENTER CONSOLE INSTALLATION

27 620-7921 Rev A Step 33. Using a Phillips head screw driver, secure the front display to the back with (8) M4 x 0.7 x 19mm long Phillips head screws. Step 34. Turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: Refer to the User’s Manual ...

Page 27 - Verify clear audio coming from both earphones.

28 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the Total Body Trainer. • As with any moto...

Page 28 - MYE® ENTERTAINMENT CENTER CONSOLE INSTALLATION INSTRUCTIONS

29 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. MYE® center console. 2. iPod® cradle. 3. iPod® center console owner’s manual. 4. MYE® operation manual. 5. Lower back cover. Note: If the center console is being installed on a new unit,...

Page 35 - YOU HAVE NOW COMPLETED THE MYE® CENTER CONSOLE INSTALLATION

36 620-7921 Rev A Step 29. Assemble the front and back display parts to-gether by sliding the bottom of the front display under the 2 tabs at the base first, then pressing front display against the back cover. Caution: Be careful not to pinch any wires. Step 30. Using a Phillips head screw driver, s...

Page 37 - PERSONAL VIEWING SCREEN (PVS) INSTALLATION INSTRUCTIONS

38 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: Step 3. Using a #2 Phillips screwdriver, remove the (8) screws on the back of the display plastic. Set the screws aside, you will need them for re-assembly. Step 4. Carefully open the displ...

Page 39 - Screws

40 620-7921 Rev A Step 9. Remove the cap cover with the Star Trac logo from the back cover plastics by removing the (2) screws using a #2 Phillips screwdriver. Retain screws for later use. Note: You will no longer need the cap cover and, if desired, you can store it away for any possible future use....

Page 44 - Tie Wrap

45 620-7921 Rev A Step 29. Take the 5” piece of tape from the PVS kit and wrap the connectors so that all of the metal sur-face is covered. Step 30. Using a 5” tie wrap from the PVS kit, bind the cables from the PVS neck to one side of the display mount. Take the tie and put it through the hole on o...

Page 47 - YOU HAVE NOW COMPLETED THE PERSONAL VIEWING SCREEN INSTALLATION

48 620-7921 Rev A Step 42. Now it is time to connect entertainment cable and power to the unit. Connect the in-house entertainment cable to the RF input at the base of the unit. Take the power supply from the kit and plug the small barrel connector to the DC input. Then take the power adapter cable ...

Page 49 - STAR TRAC

50 620-7921 Rev A STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http://www.startrac.com

Page 50 - Star Trac Fitness; E-TBT Total Body Trainer; W N E R

Star Trac Fitness TM E-TBT Total Body Trainer O W N E R ’ S M A N U A L

Page 51 - MANAGER MODE; MAINTENANCE MODE; ANAGER

STAR TRAC E SERIES TOTAL BODY TRAINERS O WNER ’ S M ANUAL 25 After using your STAR TRAC E SERIES TOTAL BODY TRAINERS for a period of time, you may wish to change some of its settings. MANAGER MODE The Manager Mode allow you to query and modify the basic settings of your Total Body Trainer. To enter ...

Page 53 - SERVICE MESSAGES; ROUBLESHOOTING

STAR TRAC E SERIES TOTAL BODY TRAINERS O WNER ’ S M ANUAL 27 Lowest Highest Default Item Value Value Value Meaning CW Prog 0 65535 0 Number of times the Continuous Watts Program was run since last reset. Alpine 0 65535 0 Number of times the Alpine Pass Program was run since last reset. Rndm Prog 0 6...