Star Trac 620-7920 - Manuals

Page 2 - Adhere to all torque and assembly specifications.

3 620-7920 Rev A GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual; the manual describes equipment setup and instructs members on how to use it correctly and safely. 1. Hex (Allen) key, 1/4” (Included) 2. Hex (Allen) key, 5/32”...

Page 3 - UNPACKING INSTRUCTIONS

4 620-7920 Rev A Step 3. Remove the side box. Step 4. Lay all boxes on the floor and verify that all components are included (see next page for details). Step 2. Remove the top cover. Step 1. Lay the unit in the area where it is going to be assembled and remove the straps. UNPACKING INSTRUCTIONS

Page 4 - Owner’s manual with warranty registration card.; Front neck assembly.

5 620-7920 Rev A Step 7. Verify components in box two (continued): 1. Neck cover. 2. Display console’s top back cover (p/n 020-7074). 3.Neck grommet. 4.Power cable. 5.Owner’s manual with warranty registration card. 6.Hardware kit. Step 8. Verify components in box two (continued): • Display console’s...

Page 5 - Verify hardware included in the hardware kit:; The motor shroud end of the frame assem-

6 620-7920 Rev A Step 9. Verify the following tools are included in the hardware kit : Step 10. Verify hardware included in the hardware kit: Step 12. With a helper, lift the treadmill frame assembly from the shipping crate platform and place it in the location where it will be used. Make sure the u...

Page 6 - INSTALLATION INSTRUCTIONS

7 620-7920 Rev A Step 3. Position neck close to the service opening in the front of treadmill so the cables go into the opening first. Step 4. Route all cables from neck into motor compart-ment through lower neck service opening. Caution: Make sure not to pinch any cables. Step 2. Remove the neck fo...

Page 7 - Note

8 620-7920 Rev A Step 6. Align the front holes and fasten with (2) 5/16-18 x 3.0”, (2) 5/16 washers and (2) lock washers. DO NOT fully tighten yet. Step 5. Insert neck into place, then align the top holes. Using the 1/4” Hex key, fasten the neck to the frame with (2) 5/16-18 x 1.0” socket head screw...

Page 8 - (left rail’s part number; DO NOT; fasten

9 620-7920 Rev A Step 10. Now install the top display rail. Align the rail’s mounting holes with the neck holes. Note: If the electronic display console was assembled to the rail; remove the screws holding it to the rail and store the display for later use. Hint: If one person is assembling the unit...

Page 9 - tighten screws fully

10 620-7920 Rev A Step 15. Now tighten the 2 front neck screws (5/16-18 x 3.0” socket head) to a torque value of 200 in-lbs (22.5 Nm). Step 14. Make sure the gap between the rails is closed and, using the 5/32” Hex key, fasten the (2) #10 button head socket screws. Tighten the screws to a a torque v...

Page 13 - LED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS

14 620-7920 Rev A Step 1. Remove electronic display console from pack-aging materials. Note: If you are installing an iPod® Kit, a MYE Entertain- ment kit or a Personal Viewing Screen kit along with this display, it is recommended that you install the kit’s center console before you mount the displa...

Page 15 - Screw Locations

16 620-7920 Rev A Step 9. Connect the main I/O cable (e) to J1 connector on the display board. Step 10. Mount the display assembly to the frame and note the screw locations (see figure above). Secure top assembly with (4) M4 screws and (4) flat 5/16 washers. Step 11. Attach ground strap of the displ...

Page 16 - YOU HAVE NOW COMPLETED THE E-TRx TREADMILL INSTALLATION

17 620-7920 Rev A Step 13. Install the top back cover piece (p/n 020-7074) onto the upper display back cover (p/n 020-7069 ). Step 14. Install the lower display back cover onto dis-play using (6) M4 screws. Next install upper display back cover onto display with (8) of the same screws, tighten all s...

Page 17 - ATTENTION; Once powered up, all features of the unit function properly.

18 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill. • As with any motorized equipment, th...

Page 18 - THIS PAGE INTENTIONALLY LEFT BLANK

19 620-7920 Rev A THIS PAGE INTENTIONALLY LEFT BLANK

Page 19 - EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS

20 620-7920 Rev A Step 2. Take out the embedded display console out of the box and remove all packing material. Verify no visual damage is present on the assembly. Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. Embedded display console. 2. E-TRe tool ...

Page 20 - Rail Stop

21 620-7920 Rev A Step 8. Position the display assembly near the top rail while a helper makes the necessary connec-tions. Step 11. Connect the rail stop cable (f) to JP9 connector on the center console board. Rail Stop Step 10. Connect headphone cable (d) coming from Hot Bar rail to audio jack on t...

Page 23 - YOU HAVE NOW COMPLETED THE EMBEDDED DISPLAY INSTALLATION; Do not use power tools or over torque the

24 620-7920 Rev A Step 21. If not done already, position the treadmill where you plan to use it. If necessary, level the tread-mill using the two adjustable feet under the tail roller. Loosen the lock nuts, rotate the feet until the treadmill is stabilized, and retighten the lock nuts. Step 22. Turn...

Page 24 - ing the Calibration and Setup.

25 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill. • As with any motorized equipment, th...

Page 26 - iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS

27 620-7920 Rev A Step 3. If the display console is already installed on the frame and the back enclosures are off, remove the screws to release the standard console and remove wires or harnesses attached to the dis-play. Step 4. Remove the standard center console from the display. Note: You will no...

Page 27 - You will no longer need the cover and it can

28 620-7920 Rev A Step 5. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front of the hot bar. Retain the screw . Step 6. Remove the headphone jack blank cover. Note: You will no longer need the cover and it can be stored away for any possible ...

Page 28 - Install the new iPod® center console.

29 620-7920 Rev A Step 9. Install the new iPod® center console. Step 10. Connect headphone cable coming from Hot Bar rail to the headphone jack on the center con-sole board. Step 11. Plug the center console keypad cable into J7 connector on the display board. Step 12. Plug the center console’s 7-pin...

Page 29 - YOU HAVE NOW COMPLETED THE iPod® CENTER CONSOLE INSTALLATION

30 620-7920 Rev A Step 16. Install and secure lower back cover then turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: Refer to the User’s Manual for calibration in- structions and other settings. YOU HAVE NOW COMPLETED THE iPod® CENTER CO...

Page 32 - You will no longer need the center console,; MYE® ENTERTAINMENT CENTER CONSOLE INSTALLATION INSTRUCTIONS

33 620-7920 Rev A Step 3. If the display console is already installed on the frame and the back enclosures are off, remove the screws to release the standard console and remove wires or harnesses attached to the dis-play. Step 4. Remove the standard center console from the display. Note: You will no...

Page 33 - You will no longer need the cover, and if de-

34 620-7920 Rev A Step 5. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front of the hot bar. Retain the screw . Step 6. Remove the headphone jack blank cover. Note: You will no longer need the cover, and if de- sired, you can store it away fo...

Page 34 - Don’t; secure console with screws yet.

35 620-7920 Rev A Step 10. Connect the headphone cable coming from Hot Bar rail to the headphone connector on the MYE® center console. Step 9. Install the new MYE® entertainment console in place. Don’t secure console with screws yet. Step 11. Plug the center console’s keypad cable into J7 connector ...

Page 35 - YOU HAVE NOW COMPLETED THE MYE® CENTER CONSOLE INSTALLATION

36 620-7920 Rev A Step 16. Turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: Refer to the User’s Manual for calibration in- structions and other settings. Step 15. Secure the MYE® center console in place using previously retained screws, ...

Page 38 - Verify following items included in hardware kit:; If the center console is being installed on a; Tighten the hex nut on the back of the neck.; PERSONAL VIEWING SCREEN (PVS) INSTALLATION INSTRUCTIONS

39 620-7920 Rev A Step 2. Verify following items included in hardware kit: 1. (1) Silicon wrap 2. (2) Tie strap 3. (1) M8 nut 4. (1) 5MM Hex (Allen) key. 5. (1) Headphone jack label. 6. (5) Screw M4x.7, 19mm, Pan Head 7. (4) M8 x 20mm Button head screws. 8. (1) Alcohol wipe. 9. (1) E-TRx Hot Bar hea...

Page 40 - Install the new PVS center console in place.

41 620-7920 Rev A Step 10. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front of the hot bar. Retain the screw . Step 11. Remove the headphone jack blank cover. Note: You will no longer need the cover, and if de- sired, it can be stored away ...

Page 41 - The headphone jacks on the audio board are

42 620-7920 Rev A Step 13. Select the E-TRx headphone mount from the kit and attach it to the available cut-out at the lower front of the hot bar, then secure with previously retained screw. Step 14. Take the E-TR headphone jack assembly from the kit and install it onto the back of the center consol...

Page 42 - Headphone; (connected to headphone jack in

43 620-7920 Rev A Step 17. Plug the center console’s 7-pin interface cable into J11 connector on the display board. Step 19. Plug the center console’s ground cable into the ground cable tab on the back display bracket. Step 18. Plug the DC power cable from the treadmill neck into either one of the D...

Page 43 - YOU HAVE NOW COMPLETED THE PERSONAL VIEWING SCREEN INSTALLATION

44 620-7920 Rev A Step 24. Turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: Refer to the User’s Manual for calibration in- structions and other settings. Step 21. Plug identified PVS connectors into the high-lighted locations on the cent...

Page 45 - STAR TRAC

46 620-7920 Rev A STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http://www.startrac.com

Page 46 - TM; W N E R

S TAR T RAC F ITNESS TM E-TR Treadmill O W N E R ’ S M A N U A L

Page 47 - MANAGER MODE; ETTINGS AND; STAR TRAC E SERIES TREADMILL O

After having used your STAR TRAC E SERIES TREADMILL for many workouts, you may wish to change some of its settings. MANAGER MODE The Manager Mode allows you to query and modify the basic settings of your treadmill. To enter Manager Mode: 1. Press and hold the , , and keys together. 2. A beep will so...

Page 48 - MAINTENANCE MODE

* When the MINIMUM SPEED or MAXIMUM SPEED parameters are changed, the Treadmill will perform an auto calibration. To termi- nate the auto calibration and return the parameter to its default setting, press the S TOP key. MAINTENANCE MODE Your Service Representative may need to check accumulated data ...

Page 50 - MOTOR CALIBRATION

* When the MINIMUM SPEED or MAXIMUM SPEED parameters are changed, the Treadmill will perform an auto calibration. To termi- nate the auto calibration and return the parameter to its default setting, press the S TOP key. MOTOR CALIBRATION The Motor Calibration function allows for calibration of the t...

Page 51 - ELEVATION CALIBRATION

ELEVATION CALIBRATION The Elevation Calibration function allows for calibration of the treadmill's elevation function. To enter the Elevation Calibration function: 1. While in the Maintenance Mode, navigate to the Elevation Calibration by the next or the previous parameter buttons. Press the key, th...

Page 52 - ROUBLESHOOTING

T ROUBLESHOOTING 42 STAR TRAC E SERIES TREADMILL O WNER ’ S M ANUAL Star Trac recommends that you refer your questions about your STAR TRAC E SERIES TREADMILL operation and suspected mal- functions to Star Trac’s Customer Service Hotline at (800) 503-1221, or USA 1-714-669-1660. However, you may wis...