Stanley VF80 - Manuals - manualsarea.com

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS; IMPORTANT

VF80 User Manual ◄ 3 SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certified dealer. Please read the following warni...

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► VF80 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

VF80 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befor...

Page 7 - HOSE SAFETY TAGS; HOSE TYPES

VF80 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 8 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

8 ► VF80 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 9 - HTMA / EHTMA REQUIREMENTS

VF80 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat ...

Page 10 - PRE-OPERATION PROCEDURES; PREPARATION FOR INITIAL USE; CHECK TOOL; OPERATING PROCEDURES; COLD WEATHER OPERATION; STORAGE; OPERATION

10 ► VF80 User Manual PRE-OPERATION PROCEDURES PREPARATION FOR INITIAL USE The tool, as shipped, has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the tool was not damaged in shipping and does not contain packing debris is all that is required. CHECK HYDRAULI...

Page 11 - TOOL PROTECTION & CARE

VF80 User Manual ◄ 11 NOTICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncouplin...

Page 12 - TROUBLESHOOTING

12 ► VF80 User Manual SYMPTOM CAUSE SOLUTION Tool does not run. Power unit not functioning. Check power unit for proper flow and pressure. 4–12 gpm/15–45 lpm at 500–2000 psi/35–140 bar. Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. Be sure hoses are...

Page 13 - ACCESSORIES

VF80 User Manual ◄ 13 Capacity........................................................................................................................................ 1700 scfm/802 lsec Flow Range ..........................................................................................................

Page 14 - VF80 PARTS ILLUSTRATION

14 ► VF80 User Manual 29 30 16 14 13 15 12 29 29 21 26 11 24 23 29 19 20 18 17 25 8 10 3 31 4 2 1 6 7 5 9 28 27 22 33 32 VF80 PARTS ILLUSTRATION

Page 15 - VF80 PARTS LIST

VF80 User Manual ◄ 15 ITEM PART NO. QTY DESCRIPTION 1 06952 1 VOLUTE 2 33458 1 BLOWER WHEEL 3 14607 1 INLET SCREEN 4 06954 1 MOTOR MOUNT BRIDGE 5 06638 1 CAPSCREW 6 00429 1 NUT 7 00152 8 TAPPING SCREW 8 06964 1 KEY 9 06960 2 ADAPTER, 90° #10 TO 1/2 NPT FEMALE 10 21445 1 MOTOR ASSY (INCL ITEMS 11 THR...