Stanley RD12 - Manual - manualsarea.com

Page 2 - All; DECLARATION OF CONFORMITY

2 ► RD12 User Manual DECLARATION OF CONFORMITY ÜBEREINSTIMMUNGS-ERKLARUNG DECLARATION DE CONFORMITE CEE DECLARACION DE CONFORMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools ______________________________________________________________________ I, the undersigned: Ich, der Unterzeichnende: Je souss...

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS; IMPORTANT

RD12 User Manual ◄ 3 SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certified dealer. Please read the following warni...

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► RD12 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

RD12 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befor...

Page 7 - HOSE SAFETY TAGS; HOSE TYPES

RD12 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 8 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

8 ► RD12 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 9 - HTMA / EHTMA REQUIREMENTS

RD12 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat ...

Page 10 - PREOPERATION PROCEDURES; PREPARATION FOR INITIAL USE; USING COOLANT; OPERATING PROCEDURES; RAIL TEMPLATES & HOLE GUIDES; OPERATION

10 ► RD12 User Manual PREOPERATION PROCEDURES PREPARATION FOR INITIAL USE The tool as shipped has no special unpacking or assem- bly requirements prior to usage. Inspection to assure the tool was not damaged in shipping and that it does not contain packing debris is all that is required. Otherwise, ...

Page 12 - TEMPLATES & HOLE GUIDES

12 ► RD12 User Manual RAIL SIZE RD12 DRILL TEMPLATE SETS: DOUBLE SIDED/ (SINGLE SIDED) GUIDE ASSY P/N: ING (MM)/[INCHES] COUNTRY 60 ASCE (6040)# ^(34525) USA 65 ASCE (6540)# ^(35975) USA 68GN (52636) 38644 [2 1/8 × 4 1/2 × 7] USA 70 ASCE # ^(49246) USA 72 CHI & NW (7250) ^(35876) USA 75 ASCE (75...

Page 15 - TOOL PROTECTION & CARE

RD12 User Manual ◄ 15 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic syste...

Page 16 - TROUBLESHOOTING

16 ► RD12 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.When diagnosing problems with operation of the drill, always check that the hydraulic power source is supplying the correct hydraulic flow and pressure to the tool as list...

Page 17 - ACCESSORIES; SPECIFICATIONS

RD12 User Manual ◄ 17 Bit Capacity ............................................................................................... up to 1-9/16 in. diameter/36 mm diameter Bit Type ................................................................................................................Carbide...

Page 18 - RD12 PARTS ILLUSTRATION

18 ► RD12 User Manual 11 2 11 1 111 11 2 RD12 PARTS ILLUSTRATION

Page 19 - RD12 PARTS LIST

RD12 User Manual ◄ 19 ITEM PART NO. QTY DESCRIPTION 1 24871 4 CAPSCREW 2 24844 1 CARRY HANDLE 3 31097 1 OPERATION DECAL 4 03787 1 GPM STICKER 5 25773 1 PRESSURE RELIEF VALVE 6 25774 1 TAMPER RESISTANT COVER 7 24868 1 FLOW CONTROL 8 00955 4 1/8" PIPE PLUG 9 31096 1 RD12 MODEL NO. STICKER 10 15909...

Stanley RD12 - Manual

Table of Contents:

Summary

Other Stanley Models