Stanley TA54 - Manuals - manualsarea.com

Page 3 - TABLE OF CONTENTS; WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; IMPORTANT

TA54 User Manual ◄ 3 TABLE OF CONTENTS SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certified dealer. Please read...

Page 4 - SAFETY SYMBOLS; LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE

4 ► TA54 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety...

Page 5 - SAFETY PRECAUTIONS

TA54 User Manual ◄ 5 SAFETY PRECAUTIONS Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating...

Page 7 - HOSE TYPES; HOSE SAFETY TAGS

TA54 User Manual ◄ 7 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: C...

Page 8 - HOSE RECOMMENDATIONS; Tool to Hydraulic Circuit Hose Recommendations

8 ► TA54 User Manual HOSE RECOMMENDATIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ...

Page 9 - HTMA / EHTMA REQUIREMENTS

TA54 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Tem...

Page 10 - OPERATION; PRE-OPERATION PROCEDURES; PREPARATION FOR INITIAL USE; OPERATING PROCEDURES; COLD WEATHER OPERATION; STORAGE

10 ► TA54 User Manual OPERATION PRE-OPERATION PROCEDURES PREPARATION FOR INITIAL USE The tool, as shipped, has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the tool was not damaged in shipping and does not contain packing debris is all that is required. CHEC...

Page 11 - TOOL PROTECTION & CARE

TA54 User Manual ◄ 11 TOOL PROTECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overhe...

Page 12 - TROUBLESHOOTING

12 ► TA54 User Manual TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Tool does not run. Power unit not functioning. Check power unit for proper flow and pressure (3–9 gpm/11–34 lpm at 1000–2000 psi/70–140 bar). Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. ...

Page 14 - SPECIFICATIONS; ACCESSORIES; SERVICE TOOLS

14 ► TA54 User Manual SPECIFICATIONS Oil Flow Range .............................................................................................................................. 3-9 gpm/11-34 lpm Pressure Range ...........................................................................................

Page 15 - TA54 PARTS ILLUSTRATION

Page 16 - TA54 PARTS LIST; Read Before Ordering Inline Valve Parts:

16 ► TA54 User Manual TA54 PARTS LIST ITEM QTY PART NO. DESCRIPTION 1 1 01038 THRUST BRIDGE WASHER 2 1 00823 CUSHION 3 1 00834 O-RING 4 1 01262 O-RING 5 1 14883 NOSE 6 1 01795 JAM NUT 7 1 14891 SEAL 8 1 14884 SEAL WASHER 9 1 04902 RETAINING RING, SPIROLOX 10 1 08434 FELT WASHER 11 1 15016 ROD WIPER ...