Stanley SK58 - Manuals - manualsarea.com

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS

SK58 User Manual ◄ 3 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PRECAUTIONS ...................................................................................................

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► SK58 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

SK58 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befor...

Page 7 - HOSE SAFETY TAGS; HOSE TYPES

SK58 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 8 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

8 ► SK58 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 9 - HTMA / EHTMA REQUIREMENTS

SK58 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat ...

Page 10 - OPERATION PROCEDURES; PRE-OPERATION PROCEDURES; CHECK POWER SOURCE; OPERATION

10 ► SK58 User Manual NOTE:If uncoupled hoses are left in the sun, pressure in- crease within the hoses may make them difficult to connect. When possible, connect the free ends of the hoses together. 5. Connect the hose from the air supply to the hose on the tool. NOTICE The air supply must be minim...

Page 11 - COLD WEATHER OPERATION

SK58 User Manual ◄ 11 8. After the rock bit has carved out a depression in the material being drilled, open the hydraulic valve le- ver fully. Readjust the motor control knob to obtain a good drilling speed. Adjust the air valve to ensure the cuttings are being extracted from the drill hole. 9. When...

Page 12 - TOOL PROTECTION & CARE

12 ► SK58 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic s...

Page 13 - TROUBLESHOOTING

SK58 User Manual ◄ 13 PROBLEM CAUSE REMEDY Tool does not run. Power unit not functioning. Check power unit for proper flow and pressure (7–9 gpm/26–34 lpm, 1500–2000 psi/105–140 bar. Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. Be sure hoses are co...

Page 14 - ACCUMULATOR CHARGING; GENERAL SERVICE NOTES; CHARGING THE ACCUMULATOR

14 ► SK58 User Manual ACCUMULATOR CHARGING 1. Perform steps 1 through 4 of the accumulator test- ing procedure above. 2. Connect the chuck of the charging assembly to the charging valve on the accumulator tester or, if pre- ferred, remove the tester from the charging valve and connect the charging a...

Page 16 - ACCESSORIES; DRILL STEELS FOR USE WITH AIR; SERVICE TOOLS

16 ► SK58 User Manual Shank Size (SK58110 Air, SK58120 Water, SK58310 UW Air) ....................................................4-1/4 in. × 1 in. Hex Shank Size (SK58130 Air) .........................................................................................................4-1/4 in. × 7/8 in...

Page 17 - SK58 PARTS ILLUSTRATION

Page 18 - SK58 PARTS LIST

18 ► SK58 User Manual ITEM PART NO. QTY DESCRIPTION 1 04763 1 AIR TUBE (SK58110/SK58130/SK58310 ONLY) 04965 1 WATER TUBE (SK58120 ONLY) 2 07064 1 VENT PLUG 3 04964 2 HANDLE GRIP ASSEMBLY 4 01714 1 NUT HEAVY HEX JAM 5 04786 2 WASHER 6 04794 1 O-RING * 7 04147 1 LOCKNUT 8 04718 1 VALVE LEVER 9 04902 1...

Page 20 - UNDERWATER TOOLS DEPTH GUIDELINE; DO NOT USE HYDRAULIC TOOLS UNDER-; Operation Overview; Percussive; Recommended Hose Diameters

20 ► SK58 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive...

Page 21 - NOTES