Stanley DL07 - Manuals - manualsarea.com

Page 2 - DECLARATION OF CONFORMITY; All

2 ► DL07 User Manual DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY ÜBEREINSTIMMUNGS-ERKLARUNG DECLARATION DE CONFORMITE CEE DECLARACION DE CONFORMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools ______________________________________________________________________ I, the undersigned: Ich, der...

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS; IMPORTANT

DL07 User Manual ◄ 3 DECLARATION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS ....................................................................................................................

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► DL07 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

DL07 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befor...

Page 7 - HOSE SAFETY TAGS; HOSE TYPES

DL07 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 8 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

8 ► DL07 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 9 - HTMA / EHTMA REQUIREMENTS

DL07 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat ...

Page 10 - PREOPERATION PROCEDURES; CHECK POWER SOURCE; DRILL OPERATION; OPERATION

10 ► DL07 User Manual PREOPERATION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated flow meter and pressure gauge, check that the hydraulic power source develops a flow of 4-12 gpm/15-45 lpm at 1000-2000 psi/70- 140 bar. 2. Make certain that the hydraulic power source is equipped with a relief va...

Page 11 - COLD WEATHER OPERATION

DL07 User Manual ◄ 11 Ductile material such as metal or wood is drilled effi - ciently when a steady down force is applied to the drill center to cause the bit to slice chips of material from the hole bottom. When drilling in metal, use a cutting lubri- cant to prolong bit life and reduce the amount...

Page 12 - TOOL PROTECTION & CARE

12 ► DL07 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic ...

Page 13 - TROUBLESHOOTING

DL07 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the wrench, always check that the hydraulic power source is supplying the correct hydraulic flow and pressure to the tool as listed...

Page 14 - TORQUE AND DRILL SPEEDS; SPECIFICATIONS

14 ► DL07 User Manual Drive Size ............................................................................................................. 1/2 inch / 1.3 cm 3-Jaw Adjustable 5/8 -16 THD Chuck Drill Torque ..............................................................................................

Page 15 - ACCESSORIES

DL07 User Manual ◄ 15 DESCRIPTION PART NUMBER WOOD AUGER BITS, 5/8 INCH HEX 9/16 inch dia × 18 inch Carbide Tipped Auger Bit (22 inch OAL) ...................................................................... 27845 13/16 inch dia × 18 inch Carbide Tipped Auger Bit (22 inch OAL) .......................

Page 16 - DL07 PARTS ILLUSTRATION

16 ► DL07 User Manual 55 53 58 33 35 30 57 27 5 29 26 14 23 36 24 25 28 4 71 69 32 31 38 20 80 34 22 37 74 54 3 41 56 75 52 6 81 66 79 40 60 1 18 59 68 72 2 17 10 64 73 63 65 67 62 49 12 48 11 77 16 44 39 4 42 7 13 19 70 21 78 61 32 8 76 15 50 1 47 43 45 9 46 15 DL07 PARTS ILLUSTRATION

Page 17 - DL07 PARTS LIST

DL07 User Manual ◄ 17 ITEM P/N QTY DESCRIPTION 1 00026 1 O-RING 2 00175 2 O-RING 3 00231 6 LOCKWASHER 4 00354 1 O-RING 5 00563 1 ROLL PIN 6 00713 2 DOWEL PIN 7 00717 1 O-RING 8 62229 2 CAPSCREW 9 01262 1 O-RING 10 01604 1 O-RING 11 02324 1 CAP AND PLUG, 1/2 INCH 12 03288 1 CAP AND PLUG, 3/8 INCH 13 ...

Page 18 - UNDERWATER TOOLS DEPTH GUIDELINE; Operation Overview; Diver; Recommended Hose Diameters

18 ► DL07 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive...

Page 19 - NOTES