Sharp AR-156 - Manuals - manualsarea.com

Page 2 - GETTING STARTED; INTRODUCTION; Conventions used in this manual

3 1 Getting star ted GETTING STARTED This chapter provides basic information for using the copier. INTRODUCTION This copier has been designed to provide intuitive operating ease while requiring a minimumamount of space. To get full use of all copier features, be sure to familiarize yourself with thi...

Page 3 - CAUTIONS; SAFETY PRECAUTIONS

4 1 Getting star ted CAUTIONS Follow the cautions below when using this copier. ● The fusing area is hot. Exercise care in this area when removing misfed paper. ● Do not look directly at the light source. Doing so may damage your eyes. ● Do not switch the copier rapidly on and off. After turning the...

Page 4 - MAIN FEATURES

5 1 Getting star ted MAIN FEATURES High-speed laser copying ● Since warm-up time is zero, copying can be star ted immediately after the power switch isturned on. ● First-copy time is only 9.6 seconds (normal mode). ● Copying speed is 15 copies/min., which adapts to business use, allowing improvement...

Page 5 - OPERATION PANEL

7 1 Getting star ted OPERATION PANEL Original to copy key and indicators : Two-sided copies from one- sided originals.Turn on Long Edge or Turn onShor t Edge can be selected. : Two-sided copies from two- s i d e d o r i g i n a l s . ( C a n b eselected only when the RSPFis used.) : One-sided copies...

Page 6 - LOADING COPY PAPER

10 1 Getting star ted LOADING COPY PAPER Raise the handle of the paper tray and pull the paper tray out until it stops. Adjust the paper guides on the paper tray to the copy paper width and length.Squeeze the lever of paper guide and slide the guide to match with the width of the paper.Move paper gu...

Page 8 - MAKING COPIES; NORMAL COPYING; A A; LOADING

12 2 Making copies MAKING COPIES This chapter describes basic copying functions and some other copying functions using thebypass tray. NORMAL COPYING This copier has two document input stations -reversing single pass feeder (RSPF) for automaticdocument feeding and an original table for manual handli...

Page 12 - Stream feeding mode; EXPOSURE ADJUSTMENT/PHOTO COPYING

16 2 Making copies When making two-sided copies from the original table, place the second original onthe original table and press the print ( ) key. ● To cancel two-sided copying after scanning the first original, press the clear( ) key. Stream feeding mode The stream feeding mode allows easy operat...

Page 13 - To select a preset copy ratio:

17 2 Making copies Set the number of copies using the copy quantity ( , ) keys and press the print ( ) key. REDUCTION/ENLARGEMENT/ZOOM Three preset reduction ratios and two enlargement ratios can be selected. The zoom functionenables copy ratio selection from 50% to 200% in 1% increments. Set the or...

Page 16 - MISFEED REMOVAL; A Misfeed in the paper feed area

27 5 Copier trouble? COPIER TROUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the copier will stop because of a misfeed.If a misfeed occurs when using the RSPF, a number may appear in the display after...

Page 17 - B Misfeed in the fusing area

28 5 Copier trouble? MISFEED REMOVAL A Misfeed in the paper feed area Gently remove the misfed paper from the paper feed area as shown in the illustration.When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the...

Page 19 - D Misfeed in the RSPF

30 5 Copier trouble? Rotate the feeding roller in the direction of the arrow and gently remove the misfedpaper from the exit area. Feeding roller Raise the fusing unit release lever, close the front cover and then close the side coverby pressing the round projections near the side cover open button....

Page 21 - DEVELOPER REQUIRED; MAINTENANCE REQUIRED

32 5 Copier trouble? DEVELOPER REQUIRED W h e n t h e i n d i c a t o r l i g h t s u p, t h e d eve l o p e r s h o u l d b e r e p l a c e d . D E V E L O P E R REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORIZED SHARP SERVICETECHNICIAN. Contact University Copy Service at Ext. 3012 as soon as possibl...

Page 22 - AUTOMATIC EXPOSURE ADJUSTMENT

35 5 Copier trouble? AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set forcopying from the original table and copying from the RSPF respectively. When adjusting the automatic exposure level for copying from the RSPF, place anorig...