Ridgid OL90150 - Manuals

Safety Instructions (continued) 6 Find and read all warning labels found onthe air compressor shown below Warning Labels DK724100AV 1000

The A-C motor used on this compressoris a capacitor start, capacitor run non-reversible induction type, having the fol-lowing specifications. It is wired at thefactory for operation on 110V-120V AC,60 Hz service. Voltage 110-120 220-240 Amperes 15.0 7.5 Hertz (Cycles) 60 Phase Single RPM 3450 Motor ...

8 The plug supplied on your tool may notfit into the outlet you are planning to use.Your local electrical code may requireslightly different power cord plug connec-tions. If these differences exist refer toand make the proper adjustments peryou local code before your tool isplugged in and turned on....

9 NOTE: The motor is prewired at the fac-tory for 120V operation. Use the follow-ing procedure to change motor voltage to240V. 1. Unplug the power cord before making or modifying connections. 2. Remove the hitch pin. 3. Toggle the motor voltage selector switch from 120V to 240V. 4. Install the hitch...

10 Thermal Overload Protector If thermal overload protector shuts motorOFF frequently look for the followingcauses. 1. Low voltage. 2. Wrong gauge wire. 3. Clogged air filter. 4. Lack of proper ventilation. 5. Unit is being used with an extension cord. See Troubleshooting Chart for correctiveaction....

11 Regulator A control that adjusts the line pressure tothe proper amount needed to operatespray guns and air tools. Tank Pressure Gauge Indicates tank pressure in psi. Line Pressure Gauge Displays the current line pressures. It isregulated by the regulator knob. Cut-in/Cut-off Pressure Specific psi...

12 Getting to Know Your Air Compressor 2 Air Filter 5 Tank Drain Valve 4 Handles 1 Belt Guard 3 Dipstick 7 Air Storage Tank 6 On/Off Switch (PressureSwitch) 12 ASME Safety Valve 10 Regulator Knob 13 Air Outlet Fittings 11 Tank PressureGauge 9 Regulated Outlet Gauge 8 Motor Voltage Selector Switch

14 Operating Your Air Compressor All lubricated compressor pumps dis-charge some condensed water and oilwith the compressed air. Install appropri- ate water/oil removal equipment and con-trols as necessary for the intended appli-cation. Remove the dipstick and fill pump with 12ounces of oil. Use sin...

16 Operating Your Air Compressor (continued) 1. Read instructions: Carefully read through this operator’s manualBEFORE OPERATING the new aircompressor. It contains informationabout operation and maintenance ofthe unit. 2. Drain tanks daily: Depressurize sys- tem prior to draining tanks. Open tankdra...

17 1. Check compressor for any visible problems, especially check air filter tobe sure it is clean. 2. Pull ring on safety valve and allow it to snap back to normal position. 3. Drain moisture from tanks daily. Shut compressor off. Depressurize systemprior to draining tanks. Drain moisturefrom tanks...

18 The tanks should be carefully inspectedat a minimum of once a year. Look forcracks forming near the welds. If a crackis detected, remove pressure from tankimmediately and replace. Tank Never attempt to repair or modi-fy a tank! Welding, drilling orany other modification willweaken the tank result...

19 Operation Daily Weekly Drain Tanks Check Air Filter Check Safety Valve Blow Dirt From Inside Motor Maintenance Schedule 1. When not in use, compressor should be stored in a cool dry place. 2. Tanks should be drained of moisture. 3. Hose should be disconnected and hung open ends down to allow any ...

20 Troubleshooting For your own safety do not tryand run the air compressorwhile troubleshooting. ! WARNING: TROUBLE PROBABLE CAUSE REMEDY Compressor will notrun Motor hums but can-not run or runs slow-ly Fuses blow/circuitbreaker trips repeat-edly 1. Unit is plugged into extension cord 2. No electr...

24 Repair Parts 1 2 3 4 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 3233 34 35 39 40 41 42 43 9 8 7 6 To pump 37 30 31