Ridgid 204830-OS - Manual

Ridgid 204830-OS

Ridgid 204830-OS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
Page: / 4

Table of Contents:

  • Page 2 – PADLOCK INSTALLATION INSTRUCTIONS FOR ALL UNITS; FOR FIELD DESK CAPABILITY; NOT; WARNING
  • Page 3 – SIDE VIEW; TOOLS REQUIRED- Hammer and flat blade screwdriver.
  • Page 4 – FOR REPLACEMENT PARTS, CONTACT RIDGID ON-SITE STORAGE EQUIPMENT; • Casters are not suitable for keeping the units in place; CAUTION; RIDGID is a registered trademark of RIDGID, Inc. and is used; • No other replacement parts are available for these models.; ” Caster Set
Loading the manual

For Models 2048-OS and 204830-OS:

• Do

NOT

put fuels, flammables, explosives or hazardous

materials inside these products.

• Gasoline, solvents, gun powder or other munitions,

dynamite, propane, acetylene or other such products
can explode if stored inside these products.

• Use these products

ONLY

for storing and transporting

electric or hand tools and equipment, and other similar
materials.

• Failure to follow these warnings or modifications or

other uses of these products could result in death, seri-
ous injury or property damage.

OPERATORS MANUAL

MODELS 2032-OS, 2048-OS, 204830-OS, 3068-OS

RIDGID ON-SITE STORAGE EQUIPMENT

DANGER

–NOTICE–

Keep hands clear when closing lid. Failure to do so could result in severe injury.

WARNING

Read and understand all instructions and warnings before operating or using this product.

–ATTENTION–

To prevent electric shock, explosion, fire and/or serious
personal injury when using storage chest with:

Extension Cord -

• Follow all Extension Cord manufacturer’s Warnings and

Instructions.

• After removing knock-out, insert Rapid Pass™ rubber

grommet. Do

NOT

insert extension cord through hole

without grommet in place (see figure 8, on page 3).

• Only use a three-wire extension cord with all three prongs

intact. Never remove the round grounding prong.

• Extension cord must be connected to a 120 Volt GFCI

protected outlet with proper ground. If GFCI outlet is not
available, use an extension cord with GFCI protection
built in.

• Check the insulation and plugs of extension cord before

using. Do

NOT

use cord if it is worn or damaged.

• Do

NOT

overload extension cord.

• Remove extension cord from the Rapid Pass™ hole

before moving or transporting storage chest.

• Only use an extension cord that is rated for outdoor

use.

• Do

NOT

connect extension cord to outlet that also sup-

plies critical safety equipment with power.

Cordless Power Tool Battery Chargers -

• See Charger’s Owner’s Manual for proper use and care

of charger and batteries. Follow all Warnings and

Instructions provided with your battery charger.
• Place chargers and electrical connections in tray.
• Chargers are Dry location use only. Do

NOT

expose to

liquid, vapor, or rain. Should your charger become wet,
Do

NOT

attempt to use. Unplug extension cord from

supply before handling wet charger or cords.

• Only use chargers and batteries that are intact and oper-

ating properly.

• Do

NOT

touch metal prongs when plugging charger into

extension cord.

• Keep flammable materials like paper or rags away from

charger, cords or connections.

• Do

NOT

place or attempt to charge lead acid, car type

batteries in storage chest.

WARNING

Any modification or unintended use of this product
shall immediately void all manufacturers warranties.
Manufacturer disclaims all liability for injuries to persons or

property resulting from any modification to, or unintended
use of this product.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - PADLOCK INSTALLATION INSTRUCTIONS FOR ALL UNITS; FOR FIELD DESK CAPABILITY; NOT; WARNING

PADLOCK INSTALLATION INSTRUCTIONS FOR ALL UNITS TOOLS REQUIRED- One wrench with 7/16” socket.PADLOCK INFORMATION- Padlock with 7/8”–1” shackle height (figure 3) (recommended Master No 5 or equiva-lent, not included). 1. Open your padlock and slide the U-bolt over the lock shackle. 2. Slide the lock ...

Page 3 - SIDE VIEW; TOOLS REQUIRED- Hammer and flat blade screwdriver.

ADJUSTING THE FLEXI-SHELF™ FOR YOUR STORAGE NEEDS FOR REMOVING THE SHELF FROM BOX 2048-OS AND 204830-OS FLEXI-SHELF™ INSTRUCTIONS 1. Be sure all contents are removed from shelf. 2. Securely grasp shelf at the right side (fac- ing box) with both hands and gently lift (figure 7). 3. Remove from box an...

Page 4 - FOR REPLACEMENT PARTS, CONTACT RIDGID ON-SITE STORAGE EQUIPMENT; • Casters are not suitable for keeping the units in place; CAUTION; RIDGID is a registered trademark of RIDGID, Inc. and is used; • No other replacement parts are available for these models.; ” Caster Set

FOR REPLACEMENT PARTS, CONTACT RIDGID ON-SITE STORAGE EQUIPMENT AT 1-800-4-RIDGID (1-800-474-3443) • Casters come as a set of four.• Load ratings are for all four wheels combined.• Load rating includes storage chest weight and contents. • Casters are not suitable for keeping the units in place when ...

Other Ridgid Models

All Ridgid Other