Ridgid AC9944 - Manuals - manualsarea.com

Page 3 - RULES FOR SAFE OPERATION; READ ALL INSTRUCTIONS

3 RULES FOR SAFE OPERATION Safe operation of this accessory requires that you read and understand this operator’s manual, the operator’s manual for the miter saw, and all labels affixed to the tool. READ ALL INSTRUCTIONS  KNOW YOUR ACCESSORY. Read the operator’s manual carefully. Learn the product’...

Page 4 - SYMBOLS; SYMBOL

4 Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. Read The Operator’s Manual Safety Alert SYMBOL NAME DESIGNATION/EXPLANATION Do not expose to rain or ...

Page 6 - LOOSE PARTS

6 The following items are included with your miter saw workstand:  Workstand Assembly  Quick Release Saw Mounting Brackets (2)  Work Supports (2)  Work Support Brackets (2)  Adjustment Knobs (4)  End Caps (2)  Wheels (2)  Hex Bolts, M10 (2)  Washers, 24 x 13 x 2 (2)  Washers, 20 x 10.5 x 1...

Page 7 - UNPACKING; ASSEMBLY

7  Pull up on lock mechanism release lever and carefully raise wheel legs.  Continue to raise wheel leg set until locked into position. UNPACKING This product requires assembly.  Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are...

Page 8 - SECURING THE LIFT ASSIST HANDLE

8 Fig. 6 ASSEMBLY SECURING THE LIFT ASSIST HANDLE See Figures 5 - 6.  Insert hex bolt into hole on each side of handle but do not insert through stand table.  Insert plastic washer between handle and stand table onto the bolt. Push bolt through the hole in the stand table.  Place a washer and loc...

Page 9 - ATTACHING THE TRANSPORT HANDLE; To install the work supports:

9 Fig. 10 ASSEMBLY ATTACHING THE TRANSPORT HANDLE See Figure 8.  Align transport handle ends with holes in stand table end caps and insert.  Place a spring washer over the screw and insert screw through each hole of the handle and leg support bracket.  Place a washer and lock nut over the end of ...

Page 12 - �To remove saw from workstand:; OPENING THE WORKSTAND; LOCK MECHANISM RELEASE LEVER

12 �To remove saw from workstand:  Push locking lever release buttons and raise the locking levers to unlock the saw mounting brackets assembly. ��  Grasp the handles on either side of the assembly and lift away from the rear edge of the table to disengage.  �With the assembly tilted slightly tow...

Page 13 - ADVERTENCIA; CLOSING AND MOVING THE WORKSTAND

13 DOBLEZ ABAJO FOLD DOWN SETUP SUJETE Y SOSTENGA EL MANGO DE APOYO FIRMEMENTE Y EN FORMA SEGURA AL DESPLEGAR O PLEGAR EL BANCO SERREZ BIEN ET TENEZ FERMEMENT LA POIGNÉE AUXILIAIRE QUAND VOUS OUVREZ OU PLIEZ LE SUPPORT INSTALE INSTALLATION PLI VERS LE BAS SECURELY GRIP AND HOLD ASSIST HANDLE FIRMLY ...

Page 14 - OPERATION; APPLICATIONS; To extend the extension arms:

14 OPERATION WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating products. Failure to do so could result in o...

Page 15 - USING THE WORK SUPPORT; To adjust the work support:

15 15 20 25 30 35 40 45 10 USING THE WORK SUPPORT See Figure 20. Rest the workpiece on top of the work support to support the workpiece during cutting operations. NOTE: More than one work support can be used on an extension arm at a time when extra support is necessary. Always lower extension arm su...

Page 16 - MAINTENANCE; GENERAL MAINTENANCE; LOCK MECHANISM HINGE

16 MAINTENANCE WARNING: When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, als...

Page 17 - SAW MOUNTING BRACKET ADJUSTMENT

17 MAINTENANCE Fig. 23 WARNING: The saw mounting brackets are designed to fit snugly over the table edges with locking levers in the open position. With the locking levers in the lowered (locked) position, you should not be able to slide the saw mounting bracket assembly along the table edges or rem...

Page 18 - NOTES

Page 19 - WARRANTY

19 WARRANTY Proof of purchase must be presented when requesting warranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications ...

Page 20 - Customer Service Information:; OPERATOR’S MANUAL; MITER SAW UTILITY VEHICLE

20 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid...