Polycom RS-232 - Manuals

This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is saved and that preset is set to be the power-on preset. Example Description Status Message S01AEC11 Enable AEC on input channel 1. S01AEC11 S01AEC10 Di...

S01AGCMAXT? Query the AGC maximum gain on input channel T . S01AGCMAXTx where x is a number between 0 and 15, depending on the current setting of the AGC maximum gain on input channel T . 8.7. AGCMIN -- Set Minimum Allowed Mic/Line Input AGC Gain This command sets the minimum gain that the AGC can a...

This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is saved and that preset is set to be the power-on preset. Example Description Status Message S01AGCRATE13 Set AGC ramp rate on input channel 1 to 3 dB/se...

S01AMDECAY>500 Increase automixer decay time by 500 ms. S01AMDECAYx , where x is between 0 and 5000 depending on the current AMDECAY setting. If this command is issued after the above example, then the status message will be S01AMDECAY? Query automixer decay time. S01AMDECAYx , where x is between...

This command is a channel integer command. See Section 6.3 and Section 6.2 for more information on this type of command. The minimum and maximum values for this command are 0 and 100, respectively. This command is saved to non-volatile memory only as part of a preset. The state of this command will ...

S01AMGATET1>3 Increase gate threshold for manual gating threshold by 3 dB for input channel 1. S01AMGATET1x , where x is between 0 and 100 depending on the current setting of the gate threshold for input channel 1. If this command is issued after the example above, then the status message will be...

This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are 0 and 5000, respectively. This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after powe...

S01AMLMM10 Disable "last mic on" mode for automixer 1. S01AMLMM10 S01AMLMM11 Set "last mic on" mode to manual for automixer 1. S01AMLMM11 S01AMLMM12 Set "last mic on" mode to automatic for automixer 1. S01AMLMM12 S01AMLMM1? Query the current setting of "last mic on" m...

for Automixer This command sets the local maximum number of open mics (NOM) allowed for the specified automixer. The NOM limit is a local limit, meaning that this limit applies only to the specific Vortex that is is set on. In contrast, the AMGNOM command is a global limit that applies to all linked...

The last byte (ä) consists of only one value. ä = 0x84 = 132 → 132 - 132 = 0 = Idle So, we know that the AEC on input 1 is in idle mode. In the above description, the data in the BLDATA command consists of 13 bytes (4 input levels + 5 output levels + 1 AEC reference level + 1 room gain level + 1 AGC...

This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is saved and that preset is set to be the power-on preset. Example Description Status Message S01CGATEEN0 Disable automatic camera gating messages. S01CGA...

S01DSPAUTO? Query the value of the DSPAUTO parameter. S01DSPAUTOx , where x is 0 or 1 depending on the current setting of the DSPAUTO paramter. 8.45. DSPLOAD -- Query Percentage of Variable DSP Resources Used This command queries the current percentage used of the available variable DSP resources. W...

ERROR#092 This error indicates an EF Bus ID conflict. See the Vortex user manual for information on valid device IDs. ERROR#093 This error indicates an EF Bus reference conflict. This error occurs when more than one Vortex is placing its AEC reference on the bus. Use the BUSREF command to remove the...

S01FADERIA? Query the fader gain on input A. S01FADERIAx , where x is a number between 0 and 30, depending on the current setting of the fader gain on input channel A. S01FADERI*6 Set fader gain on all inputs (1, A, B, T) to 6 dB. S01FADERI*èèèè S01FADERI*ìääì Set fader gain on input channels A and ...

8.52. FPPSWD -- Change Front Panel Password This command sets or queries the front panel password. This password is used in conjunction with the FPLOCK command. The front panel must be unlocked (' FPLOCK0 ') in order to use this command to set or query the front panel password. If the front panel is...

This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are -20 and 20, respectively. This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after powe...

This command sets the gain of the dial tone received from the phone interface. This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are -20 and 20, respectively. This command is saved to non-volatile memory ...

Example Description Status Message S01GAINIA10 Set gain on input A to 10 dB. S01GAINIA10 S01GAINIA? Query the gain on input A. F01GAINI2xB01GAINITxS01GAINIAxQ01GAINIAxT01GAINITx , where x is a number between 0 and 30, depending on the current setting of the gain on input channel A. S01GAINI*6 Set ga...

S01GAINO*äììä Set gain on output channels 1 and T to 0 dB, and gain on output channels A and B to 9 dB. S01GAINO*äììä S01GAINO*? Query gain settings on all output channels (1, A, B, T) . S01GAINO*abcd , where a - d are each between <space> and ÿ , depending on the current setting of the gains ...

will be restored after power-up only if a preset is saved and that preset is set to be the power-on preset. Example Description Status Message S01GAINSIT6 Set tone output gain to 6 dB. S01GAINSIT6 S01GAINSIT>3 Increase tone output gain by 3 dB. S01GAINSITx where x is the new value of the tone out...

status of all the microphone inputs. On the EF2211 and EF2210, there is only one microphone, so the wildcard character is of limited use. The GATEEN can be used to have gating information sent automatically instead of having to poll this command. Also see the CGATE command, which only reports microp...

iLABELx,y where i is the device type and ID, x is the label specifier, and y is the label text (to set the label) or a ? character (to query the label). The label specifiers are as follows: Label Specifier Description D A label for the device itself. SG A label for the signal generator. I1, IA, IB, ...

preset. Example Description Status Message S01LAGCLINKAB1 Enable stereo AGC linking on inputs A and B. S01LAGCLINKAB1 S01LAGCLINKAB0 Disable stereo AGC linking on inputs A and B. S01LAGCLINKAB0 S01LAGCLINKAB2 Toggle stereo AGC linking on inputs A and B. S01LAGCLINKABx , where x is 0 or 1 depending o...

LAGCMIN is set to -10 , then the AGC for that channel can apply a minimum of -10 dB of gain to the input signal. This command was introduced in firmware version 2.5.0. This command is a channel integer command. See Section 6.3 and Section 6.2 for more information on this type of command. The minimum...

This command sets or queries the status of the line echo canceller (LEC). This command is a boolean command. See Section 6.1 for more information on this type of command. This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up ...

Example Description Status Message S01LIEN1 Enable automatic logic input status messages. S01LIEN1 S01LIEN0 Disable automatic logic input status messages. S01LIEN0 S01LIEN2 Toggle automatic logic input status messages. S01LIENx , where x is 0 or 1 depending on the current setting of LIEN . S01LIEN? ...

8.81. LIK -- Delete One or All Logic Input Pin Commands This command "kills" or deletes all commands for a given logic input pin. In other words, the commands associated with LIA , LID , and LIH will be deleted for the specified logic input. A wildcard character can also be specified for the...

S01LIM100101101111011111111111 Mask (disable) logic inputs 2, 3, 5, 8, and 13. S01LIM100101101111011111111111 S01LIM? Query current logic input mask. S01LIMabcdefghijklmnopqrstuvwx where a - x are each 0 or 1 depending on the current state of the logic input mask. 8.83. LIN -- Assign Command to Logi...

closed switch would ground the input, and a closed switch would normally be considered active. This command affects the operation of the LIA , LID , and LIH commands. If a logic input pin's polarity is reversed, the operation of these commands is reversed. By default, the polarity for all pins is se...

State This command is used to define the conditions under which a given logic output pin goes into the active state. By default the logic output pins are active high. Active high is the default because it would light an LED connected to the output when the output was in the active state. The polarit...

S01LOEN? Query automatic logic output status messages. S01LOENx , where x is 0 or 1 depending on the current setting of LOEN . 8.89. LOK -- Delete One or All Logic Output Pin Commands This command "kills" or deletes all commands for a given logic output pin. In other words, the commands asso...

Example Description Status Message S01LOM10010110111101111111 Mask (disable) logic outputs 2, 3, 5, 8, and 13. S01LOM10010110111101111111 S01LOM? Query current logic output mask. S01LOMabcdefghijklmnopqrst , where a - t are each 0 or 1 depending on the current state of the logic output mask. 8.91. L...

● any PRESET command ● any MACRO command ● any logic input or output command If an attempt to assign an invalid command to a macro is made (via MACROA ), then the error condition ERROR#074 will be generated. An error will be generated if the specified command is not a valid command. However, an erro...

This command is used to start writing a new macro with a specified macro number. This command is used in conjunction with the MACROA and MACROW commands to create a new macro. If this command is sent while another macro is in the process of being written (before the MACROW command is sent), then the...

This command selects which signal is displayed on the front panel LED meter. The options correspond to either the telepone input or telephone output. The labels for the the telephone input and output are IT and OT , respectively. This command is saved to non-volatile memory only as part of a preset....

This command is a matrix boolean command. See Section 6.4 and Section 6.1 for more information on this type of command. This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is saved and that preset is set to...

S01MIC1? Query enabled status of microphone gain stage for input channel 1. S01MIC1x , where x is 0 or 1 depending on the current enabled state of the microphone gain stage on input channel 1. 8.103. MINI -- Enable Modem Initialization String This command controls whether or not the modem initializa...

S01MUTEO*? Query mute status of all outputs. S01MUTEO*abcd , where each of the letters (a, b, etc.) is either 0 or 1 depending of the current status of the mute on the corresponding output. If this command was sent after the example above, then the status message would be S01MUTEO*0110 8.109. NC -- ...

cancel 10 dB of noise. Higher numbers mean more cancellation will be applied, but may result in slight artifacts depending on the characteristics of the noise. Typical settings are 10 dB for normal cancellation and 6 dB for light cancellation. When the wildcard character, ' * ', is used to specify t...

This command controls the non-volatile memory lock feature. When NVLOCK is enabled, the user may not save any system settings to non-volatile memory. This includes global parameters, presets, macros, labels, and logic assignments. The lock applies whether the user tries to make the changes via RS-23...

S01NVPSWD? Query the current non-volatile memory password. S01NVPSWDlemur 8.114. PEQIA -- Set All Parameters for Specified Parametric EQ Input Stage This command sets or queries all of the parameters for the parametric equalizer (EQ) filters on input channels 1, A, B, and T input channel T. Each cha...

S01PEQIAB,1,? Query the current parameter settings for the parametric eq filter on input B , band 1. S01PEQIAB,1,t,f,b,g,s,e , where the parameters t , f , b , g , s , and e correspond to the current settings of the type, frequency, bandwidth, gain, slope, and enabled parameters, respectively. If th...

S01PEQIF1,2,1250 Set frequency of parametric EQ on input 1 , band 2 to 1250 Hz. S01PEQIF1,2,1250 S01PEQIFB,1,? Query current frequency setting of parametric EQ on input B , band 1. S01PEQIFB,1,f , where f is the current setting of the frequency parameter for the parametric EQ on input B , band 1. If...

(EQ) filters on input channels 1, A, B, and T . Each channel has five bands of parametric EQ that can be independently controlled. For the Linkwitz-Riley filters, the slope can either be 12 or 24 (dB/Octave).For the low shelf and high shelf filters, the minimum value for the slope parameter is 1, an...

parameter, the filter type, is specified instead of all the parameters. See the PEQIA command for more information. To set the slope parameter for an output parametric EQ filter, use the PEQOT command. To set all the parameters for an output parametric EQ filter, use the PEQOA command. This command ...

preset. Example Description Status Message S01PEQOB1,2,40 Set bandwidth of parametric EQ on output 1 , band 2 to 40 1/100th octaves. S01PEQOB1,2,40 S01PEQOBB,1,? Query current bandwidth setting of parametric EQ on output B , band 1. S01PEQOBB,1,b , where b is the current setting of the bandwidth par...

This command sets or queries the frequency parameter (in Hz) for the parametric equalizer (EQ) filters on output channels 1, A, B, and T . Each channel has five bands of parametric EQ that can be independently controlled. The minimum and maximum values for the frequency parameter are 20 and 20000, r...

This command executes the preset corresponding to the specified number, which must be between 0 and 47. The preset must either be a pre-defined factory preset (0 - 15) or a user preset (16 - 47) that has been previously defined via the PRESETW command. If the specified preset is empty, then an error...

Example Description Status Message S01PRESETX18 Execute preset number 18. Status messages for all the commands in the preset will be generated first, followed by the message: S01PRESETX18 8.137. REDIAL -- Redial the Last Dialed Phone Number Executing this command causes the Vortex to redial the last...

S01RING1 Enable auto answer mode. S01RING1 S01RING0 Disable auto answer mode. S01RING0 S01RING2 Toggle auto answer mode. S01RINGx , where x is 0 or 1 depending on the current state of auto answer mode. S01RING? Query auto answer mode. S01RINGx , where x is 0 or 1 depending on the current state of au...

S01SGMUTE2 Toggle mute on signal generator. S01SGMUTEx , where x is 0 or 1 depending on the current state of the signal generator mute. S01SGMUTE? Query signal generator mute. S01SGMUTEx , where x is 0 or 1 depending on the current state of the signal generator mute. 8.143. SGTYPE -- Set Type of Sig...

6 quick double buzz 7 long single buzz The SOUNDL and SOUNDP were originally implemented to allow users to implement custom passcode systems that require users calling in via phone to enter a passcode before entering the conference. The sound commands could be used to provide feedback to the caller ...

This command sets or queries the amount of time (in milliseconds) between each new screen of the LCD screen saver. This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are 500 and 600000, respectively. This ...

S01SSTEXT0,1,? Query the text of the second line of the first screen. S01SSTEXT0,1,<string> , where <string> is the text of the second line of the first screen. If this command was issued after the example above, then the status message would be S01SSTEXT0,1,funky music . 8.150. SWRESET ...

S01VTXMODIB0 Disable VTX mode on input B. S01VTXMODIB0 S01VTXMODIB2 Toggle status VTX mode on input B. S01VTXMODIBx , where x is either 0 or 1 depending on the current status of VTX mode on input B. S01VTXMODIA? Query status of VTX mode on input A. S01VTXMODIAx , where x is either 0 or 1 depending o...