Polycom 8000 - Manuals

Contents 0 About this Guide ...................................................................... 3 Polycom Model Numbers ..................................................................3 Related Documents .............................................................................3 Customer Sup...

SpectraLink 8000 SVP Server: Administration Guide for SRP Multiple SVP Servers Multiple SVP Server environments are those which have more than one SVP Server. Up to 16 SVP Servers may be installed in any one subnet. The Timing Function In the SpectraLink Gateway environment, SVP Servers provide the ...

SpectraLink 8000 SVP Server Overview SpectraLink 8000 SVP Server Capacity The table below shows the capacity of SpectraLink 8000 Telephony Gateways in a multiple SVP Server environment. The table shows the total possible calls at 100% active calls. However, since it is unlikely that all handsets wil...

SpectraLink 8000 SVP Server: Administration Guide for SRP Notes on System Configuration Wireless telephones cannot roam with uninterrupted service between subnets unless specific LAN components are present. Certain AP/Ethernet switch combinations establish a layer-2 tunnel across subnets that enable...

SpectraLink 8000 SVP Server Overview System Diagram The following diagram shows one SpectraLink 8000 SVP Server residing on a network with five SpectraLink 8000 Telephony Gateways, wireless LAN APs, and Ethernet switch: 2-001_F.doc 11 (SpectraLink 8000 Telephony Gateway system example) SpectraLink 8...

SpectraLink 8000 SVP Server: Administration Guide for SRP System Components SpectraLink e340/h340/i640 and 8020/8030 Wireless Telephones Employees can carry wireless telephones to make and receive calls as they move throughout the building. The wireless telephones are to be used on-premises; they ar...

SpectraLink 8000 SVP Server Overview wireless data devices. Contact Polycom, or a certified Polycom distributor, for specific information about your facility’s needs. The SpectraLink system must connect to APs that utilize SVP. Contact Polycom, or a certified Polycom distributor, to verify that your...

SpectraLink 8000 SVP Server: Administration Guide for SRP The Front Panel of the SVP Server The SVP Server’s front panel contains ports to connect to power, the LAN, and to an administrative computer via an RS-232 port. Status LEDs supply information about the SVP Server’s functioning. PWR 3 4 5 1 2...

2 Installing the Spectralink 8000 SVP Server As shown in the system diagram the SVP Server is connected to the Ethernet switch. The specifications covered here allow for great flexibility in physical placement of the components within stated guidelines. Required Materials The following equipment mus...

SpectraLink 8000 SVP Server: Administration Guide for SRP • A maximum distance of 325 feet (100 meters) from the Ethernet switch. Install the SVP Server The SVP Server may be mounted on a rack or to a wall. Mount the SVP Server on a rack The rack mount kit is designed for mounting equipment in a sta...

Installing the SpectraLink 8000 SVP Server PN: 1725-36032-001_F.doc 1 Connect SVP Server to LAN Using a Cat. 5 cable, connect the NETWORK port on the SVP Server to the connecting port on the Ethernet switch. Connect power 1. Connect the power plug from the AC adapter to the jack labeled PWR on the S...

3 Configuring the SpectraLink 8000 SVP Server During initial setup of the SVP Server the IP address is established and the maximum number of active calls per AP is set. Optionally, you may enter a hostname and a location for software updates via TFTP. Connecting to the SVP Server The initial connect...

SpectraLink 8000 SVP Server: Administration Guide for SRP Connecting via telnet Telnet can only be used after the SVP Server’s IP address is configured. The Telnet method of connection is used for routine maintenance of the SpectraLink Server for both local and remote administration, depending on yo...

SpectraLink 8000 SVP Server: Administration Guide for SRP SendAll In a system with multiple SVP Servers, the SendAll option is provided to speed configuration and to ensure identical settings. The S=SendAll option allows you to send that configuration parameter to every SVP Server on the LAN. SendAl...

SpectraLink 8000 SVP Server: Administration Guide for SRP Syslog Server Logging can be set to Syslog or NONE . If Syslog is set, a message is sent to the syslog server when an alarm is triggered. Disable Telnet service Prevents Telnet access into the SVP Server. Reset the SVP Server for the change t...

Configuring the SpectraLink 8000 SVP Server The SVP Server will automatically lock for maintenance if the IP address is changed. When this Maintenance Lock occurs, the SVP Server must be reset upon exit. All active calls are terminated during a reset. SVP-II Mode Set to NetLink when using a SpectraL...

SpectraLink 8000 SVP Server: Administration Guide for SRP that the administrator cannot change this option. It is automatically set by the system. Reset the system at exit to clear Maintenance Lock . Inactivity Timeout (min) Set the number of minutes the administrative module can be left unattended ...

Configuring the SpectraLink 8000 SVP Server RTP traffic is the audio traffic to the PBX. It requires voice quality. PBX traffic is not audio to the PBX. Inter-SVP2 traffic is the information-passing protocol that SVP Servers use to communicate with each other. The final DSCP tag of traffic for packe...

PN: 1725-36032-001_F.doc 31 5 Software Maintenance The SVP Server uses proprietary software programs written and maintained by Polycom Corporation. The software versions that are running on the system components can be displayed via the System Status screen. You may obtain information about software...

SpectraLink 8000 SVP Server: Administration Guide for SRP system function and to troubleshoot areas that may be experiencing trouble. Error Status The Error Status screen displays any alarms that indicate some system malfunction. Some of these alarms are easily remedied and others require a call to ...

SpectraLink 8000 SVP Server: Administration Guide for SRP fifo – overrun occurred during reception alignment – nonoctet-aligned packets (number of bits NOT divisible by eight) multicast – packets received with a broadcast or multicast destination address TX – Ethernet statistics concerning the trans...

PN: 1725-36032-001_F.doc 39 Safety Notices WARNING: Changes or modifications to this equipment not approved by SpectraLink Corporation may cause this equipment to not comply with part 15 of the FCC rules and void the user’s authority to operate this equipment. WARNING: SpectraLink products contain n...

Index A Access Point, description .....................................13 Alarms ....................................................................34 C Configuration Initial setup .......................................................22 Customer Support Hotline ......................................