Pelco TLR3168 - Manuals - manualsarea.com

Page 2 - CONTENTS; Section

2 Pelco Manual C673M (2/01) CONTENTS Section Page GENERAL .......................................................................................................................... 5 SAFEGUARDS, WARNINGS, CAUTIONS, AND CARE ............................................ 6UNPACKING INSTRUCTIONS ..........

Page 4 - LIST OF ILLUSTRATIONS; Figure; LIST OF TABLES; Table

4 Pelco Manual C673M (2/01) LIST OF ILLUSTRATIONS Figure Page 1 Typical System Setup ....................................................................................... 12 2 Connecting a VCR to a Multiplexer ................................................................... 13 3 Alarm Recording...

Page 5 - WARNING; AVERTISSEMENT; CET APPAREIL À LA PLUIE NI À L’HUMIDITÉ.; GENERAL

Pelco Manual C673M (2/01) 5 RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol,within an equilateral triangle...

Page 6 - The included

6 Pelco Manual C673M (2/01) SAFEGUARDS, WARNINGS, CAUTIONS, AND CARE Observe the following WARNINGS before installing and using this product. Follow allwarnings and instructions marked on the VCR. Instructions Read all the safety and operating instructions before operating the VCR. Keep theinstructi...

Page 9 - TLR3168 FEATURES AND FUNCTIONS; The battery backup

Pelco Manual C673M (2/01) 9 TLR3168 FEATURES AND FUNCTIONS The TLR3168 Time-Lapse VCR is a powerful surveillance tool designed for industrial andsecurity recording. The unit supports both T-120 and T-160 tapes. • T-120 TapesThe unit can record for 6, 18, 30, 48, 72, 96, 120, or 168 hours. • T-160 Ta...

Page 10 - QUICK START; BASIC START; This section is

10 Pelco Manual C673M (2/01) QUICK START BASIC START 1. Decide where to locate the VCR. Do all system hookups first (camera, multiplexer,etc.) if you are installing the VCR where you cannot access its rear panel. 2. Connect the VCR to other equipment (refer to the Installation and Connecting the VCR...

Page 11 - INSTALLATION; PRE-INSTALLATION CAUTIONS; If you need to record multiple cameras, a multiplexer is required.; SECURING THE VCR CONTROLS; Pelco recommends using a CCTV monitor.

Pelco Manual C673M (2/01) 11 INSTALLATION PRE-INSTALLATION CAUTIONS • Provide secure power to system components. Prevent overloading or shorting bydedicating power circuits to the surveillance equipment. Restrict access to thesurveillance system circuit breakers, switches, and equipment power cords....

Page 12 - Remove the VCR and all cables from the box.; Figure 1. Typical System Setup

12 Pelco Manual C673M (2/01) INSTALLATION 1. Remove the VCR and all cables from the box. 2. Place the VCR in a suitable location. 3. If installing in a rack, place the VCR in the rack before making cable and powerconnections. Refer to the documentation included with the rack kit for installationinst...

Page 13 - CONNECTING THE VCR TO A MULTIPLEXER; Cameras and; Figure 2. Connecting a VCR to a Multiplexer; Figure 2 shows how to connect the VCR to an MX4000 Series Genex

Pelco Manual C673M (2/01) 13 CONNECTING THE VCR TO A MULTIPLEXER NOTE: Cameras and monitors are connected tothe multiplexer. Figure 2shows the connection be-tween the VCR and anMX4000 Series Genex Mul-tiplexer. Refer to the multi-plexer manual for additionalcomponent connections. Figure 2. Connectin...

Page 14 - ALARM RECORDING CONNECTION; Figure 3. Alarm Recording Connection; CONNECTING FOR SERIES RECORDING; Figure 4. Connecting VCRs for Series Recording; CONNECTING FOR REMOTE RECORDING; Figure 5. Connecting for Remote Recording; Connect the VCR with a remote switch as shown in Figure 5.

14 Pelco Manual C673M (2/01) ALARM RECORDING CONNECTION Figure 3. Alarm Recording Connection You can confirm an alarm from a distance by connecting the ALM OUT terminal with anexisting alarm system panel or other peripherals, such as a buzzer. Connect the VCR andother peripherals as shown in Figure ...

Page 15 - CONNECTING FOR SYNCHRONOUS RECORDING; Figure 6. Connecting for Synchronous Recording; CONNECTING FOR EXTERNAL TIME CLOCK ADJUSTMENT; Figure 7. Connecting for External Time Clock Adjustment

Pelco Manual C673M (2/01) 15 CONNECTING FOR SYNCHRONOUS RECORDING Figure 6. Connecting for Synchronous Recording Connect the VCRs as shown in Figure 6. The number of VCRs varies according to therecording time mode selected. CONNECTING FOR EXTERNAL TIME CLOCK ADJUSTMENT Figure 7. Connecting for Exter...

Page 16 - CONNECTING THE VCR TO A PC; Figure 8. VCR to PC Connection; CONNECTING TO A PC FOR REMOTE CONTROL

16 Pelco Manual C673M (2/01) CONNECTING THE VCR TO A PC IMPORTANT: Before con- necting the hardware, un-plug the VCR’s power cordfrom the wall outlet, and turnoff the PC. Figure 8. VCR to PC Connection 1. Connect the RS-232C cross cable to the PC’s RS-232C terminal. 2. Connect the other end of the c...

Page 17 - Cable Connections; FRAME

Pelco Manual C673M (2/01) 17 Cable Connections Before connecting the hardware, unplug the VCR’s power cord from the wall outlet, andturn off the PC. Connect the VCR’s RS-232C IN terminal to the PC’s serial port. 1. When the PC’s RS-232C connector is DB25. 2. When the PC’s RS-232C connector is DB9. F...

Page 18 - CONTROLS; FRONT PANEL; Figure 9. Front Panel

18 Pelco Manual C673M (2/01) CONTROLS FRONT PANEL Figure 9. Front Panel 1. POWER buttonPress for on; press again for off. The POWER indicator lights when the VCR is turned on. 2. Cassette loading slotInsert the cassette in this slot to load it. 3. SHUTTLE ringUse to adjust the playback speed and to ...

Page 20 - FLUORESCENT DISPLAY; Figure 10. Fluorescent Display; Lights during counter memory stop.

20 Pelco Manual C673M (2/01) FLUORESCENT DISPLAY Figure 10. Fluorescent Display 1. M (counter memory stop/month) indicator• Lights during counter memory stop. • Also, lights when the month (of time and date) is being entered through the frontpanel. 2. PL (power loss) indicatorLights when the VCR is ...

Page 22 - REAR PANEL; Figure 11. Rear Panel; Input Terminals

22 Pelco Manual C673M (2/01) REAR PANEL WARNING: The included power cord is used for 120VAC, 60 Hz. Never connectthe power cord to any outputor power supply having a dif-ferent voltage or frequency.Make sure the power cord isunplugged before makingany rear panel terminalconnections. Figure 11. Rear ...

Page 23 - JOG AND SHUTTLE CONTROLS; Figure 12. JOG Dial and SHUTTLE Ring; USING THE JOG DIAL; Turn by using your finger on the indent.; USING THE SHUTTLE RING

Pelco Manual C673M (2/01) 23 5. MIC jackJack for connecting a microphone rated at 600 ohms impedance. 6. AUDIO IN connectorAudio input connector (RCA pin). 7. AUDIO OUT connectorAudio output connector (RCA pin). 8. VIDEO IN connectorInput connector for video signal (BNC connector). Connect cameras h...

Page 24 - ADJUSTING THE CLOCK; Turn the SHUTTLE ring right. The VCR’s clock is now set.; ADJUSTING TO THE EXACT SECOND

24 Pelco Manual C673M (2/01) ADJUSTING THE CLOCK You can adjust the VCR’s clock on the front panel even when the VCR is turned off. (Youcan also enter time and date information through the First Time Set Up menu.) This functionlets you enter the order of the time, month, day, and year. The hour time...

Page 25 - PROGRAMMING; GENERAL PROGRAMMING INSTRUCTIONS; Menu

Pelco Manual C673M (2/01) 25 PROGRAMMING GENERAL PROGRAMMING INSTRUCTIONS The following is a universal procedure that shows how programming is done on the VCR.Use the JOG dial to select items, turn the SHUTTLE ring to the right to enter, and turn theSHUTTLE ring to the left to exit. 1. Press the MEN...

Page 26 - QUICK GUIDE TO THE MENU STRUCTURE; Figure 14. Menu Tree

26 Pelco Manual C673M (2/01) QUICK GUIDE TO THE MENU STRUCTURE The VCR’s operating parameters are set through various on-screen menus. Program yourchoices on the menus according to the instructions on the following pages. Figure 14. Menu Tree 00445 <TIMER PROGRAM> PROGRAM TO RECORD HOLIDAY SET...

Page 27 - MAIN MENU; Figure 15. Main Menu; DISPLAY MENU; Figure 16. Display Menu; alarm recording counter.; SMALL; The letters become small.; LARGE; The letters become large.; BLUE BACK; This is where you set the background color.; ON; The recorded picture is overlaid with the menu display.

Pelco Manual C673M (2/01) 27 MAIN MENU Figure 15. Main Menu The contents of the Main menu are as follows. Access it by pressing the MENU button. • DISPLAYSets the format to display the time and date on the monitor. • TIMER PROGRAMSets the timed recordings. • RECORDING SET UPSets the alarm recording ...

Page 28 - TIMER PROGRAM; Figure 17. Timer Program Illustration; Timer Recording section for more detailed information; DW

28 Pelco Manual C673M (2/01) TIMER PROGRAM Figure 17. Timer Program Illustration This is where you set the program number, day of the week, starting and ending times, andthe recording mode. (Refer to the Timer Recording section for more detailed information and procedures.) (program number) This num...

Page 29 - RECORDING SET UP MENU; Figure 18. Recording Set; Up Menu; Refer to the

Pelco Manual C673M (2/01) 29 RECORDING SET UP MENU Figure 18. Recording Set Up Menu Refer to the Programming for Alarm Recording section for programming instructions for the following fields. ALARM REC MODE Sets the alarm recording mode. • If TAPE LENGTH in the First Time Set Up menu is setto T-120,...

Page 30 - REAR TERMINAL MENU; Figure 19. Rear Terminal

30 Pelco Manual C673M (2/01) REAR TERMINAL MENU Figure 19. Rear Terminal Menu Table B. Call Out/Tape End CALL OUT Sets the call signal output at the end of the tape. Turns on or off thesignal coming from the CALL terminal when the end of the tape isreached during recording. If a problem occurs durin...

Page 31 - MODE OUT; REC – During recording; REC IN; Sets the REC IN terminal’s operating mode.

Pelco Manual C673M (2/01) 31 MODE OUT Sets the state in which the signal output at the MODE OUT terminal isswitched to active. When you turn the JOG dial, the display switches inthe following order, and under the following circumstances: • REC – During recording • PLAY – During playback • POWER – Wh...

Page 32 - To stop the buzzer,; Figure 20. First Time Set; TIME DATE ADJUST

32 Pelco Manual C673M (2/01) MAINTENANCE MENU Refer to the Maintenance section for instructions and procedures. FIRST TIME SET UP MENU NOTE: Quasi v-sync must be set OFF for some multi-plexers to work properly.With the Pelco MX4000Series Genex Multiplexer,setting quasi v-sync on oroff has no apparen...

Page 33 - TRANSMISSION RATE; ADDITIONAL MATERIAL; Alarm recording counter

Pelco Manual C673M (2/01) 33 RS-232C MENU Figure 21. RS-232C Menu The RS-232C menu is where you set parameters for controlling the VCR with a PC. TRANSMISSION RATE Sets the transmission rate. Turn the JOG dial to switch thedisplay in the following order: 1200 (bps), 2400, 4800, 9600,1200. DATA BIT L...

Page 34 - SET THE DAY AND TIME; If power goes out

34 Pelco Manual C673M (2/01) SET THE DAY AND TIME Keep the following in mind: • You must set the day and time before performing timer programming. • The year 2000 is shown as 00. • The clock is in 24-hour format. • The alarm recording counter appears only during alarm recording. Do the following to ...

Page 35 - LOADING, UNLOADING, PROTECTING THE TAPE CASSETTE; LOADING; CORRECT

Pelco Manual C673M (2/01) 35 LOADING, UNLOADING, PROTECTING THE TAPE CASSETTE You can load video cassette tapes into your VCR as long as it is plugged into a powersource. Loading a cassette automatically turns the VCR on even if its power switch isturned off. Use only video cassette tapes marked VHS...

Page 36 - Table C. Tape Replacement by Use

36 Pelco Manual C673M (2/01) UNLOADING 1. Press the EJECT button on the front of the VCR. Even in standby mode the VCR will eject a video cassette. When you press EJECT,the VCR automatically turns on, ejects the tape, and turns off. You cannot eject a tape while recording without first pressing the ...

Page 37 - RECORDING; MANUAL RECORDING

Pelco Manual C673M (2/01) 37 RECORDING MANUAL RECORDING NOTE: Perform steps 3-7 to activate super resolutionrecording mode. Otherwise,skip to step 8. 1. Turn on the VCR and peripheral devices. 2. Load a cassette with the erasure prevention tab intact. 3. Press the MENU button. The Main menu appears....

Page 38 - RECORDING MODE; Recording Mode; RECORDING CHECK FUNCTION; Press the MENU button. The Main menu appears.

38 Pelco Manual C673M (2/01) RECORDING MODE Pressing the REC/PLAY MODE button switches the recording mode in the following order: • For T-120 tape: 6H, L18H, L30H, 48H, 72H, 96H, 120H, 168H • For T-160 tape: 8H, L24H, L40H, 64H, 96H, 128H, 160H, 224H Table D. Recording/Playback Times Recording Mode ...

Page 39 - Table E. Action When Tape End Is Reached by Setting; STOP; REPEAT; Same as above; ALARM•PROT; Recommended Number of Tape Uses; SERIES RECORDING; Series Recording 2

Pelco Manual C673M (2/01) 39 Table E. Action When Tape End Is Reached by Setting When there arealarm recordingson the tape When there is NOalarm recordingon the tape STOP The tapestops. Same asabove REWIND The tape automatically rewindsto the beginning (except intimer recording) and stops. Same as a...

Page 40 - REMOTE RECORDING

40 Pelco Manual C673M (2/01) REMOTE RECORDING This function lets you control the start and end of recording from a remote location. TheVCR starts recording when the REC IN terminal is grounded. Refer to Figure 5 for theremote recording connection. An index signal is not recorded during remote record...

Page 41 - SYNCHRONOUS RECORDING; Figure 22. Synchronous Recording Sequence; Recording Time Mode; The programming procedure is as follows

Pelco Manual C673M (2/01) 41 SYNCHRONOUS RECORDING Several camera images can be mixed together through a camera switcher and thenrecorded separately onto several VCRs. To do so, assign a camera to each VCR. The VCRrecords only the camera assigned to it. This allows recording without gaps. If you hav...

Page 44 - ALARM RECORDING; When an alarm occurs, the VCR switches to alarm recording.; Table G. Minimum Interval Between Recordings; Alarm Recording; An alarm recording is cancelled if the tape reaches its end.; Figure 23. VCR Switches to Alarm Mode; Alarm signal input; Recording

44 Pelco Manual C673M (2/01) ALARM RECORDING When an alarm occurs, the VCR switches to alarm recording. • Set the alarm recording mode and alarm recording period in the Recording Set Upmenu. Refer to the Recording Set Up Menu section for field definitions and additional information and the Programmi...

Page 45 - PROGRAMMING FOR ALARM RECORDING; Alarm recording stops when the end of the tape is reached.; If an alarm input is

Pelco Manual C673M (2/01) 45 PROGRAMMING FOR ALARM RECORDING Alarm recording will continue for the period set in the ALARM REC DURATION field, even ifa timer recording has reached its end time. Alarm recording stops when the end of the tape is reached. Emergency recording activates alarm recording e...

Page 46 - RECORDING AFTER A POWER FAILURE; MAINTENANCE; POWER LOSS LIST; Figure 24. Maintenance; VIEWING THE POWER LOSS LIST; CLEARING THE POWER LOSS LIST

46 Pelco Manual C673M (2/01) RECORDING AFTER A POWER FAILURE After a power failure during manual, timer, or alarm recording, the VCR turns itself on whenthe power is restored and begins recording in the same mode as before the failure. When power is restored, an “X” appears next to the present time ...

Page 48 - ELAPSED TIME AND REPEAT RECORDING TIMES DISPLAY; ELAPSED TIME; The number of tape uses is reset when a new tape is inserted.

48 Pelco Manual C673M (2/01) ELAPSED TIME AND REPEAT RECORDING TIMES DISPLAY The repeat recording times and elapsed time are shown on the bottom of the Maintenancemenu. ELAPSED TIME The elapsed time indicates the total time the VCR has been used for recording and playback(up to 89,999 hours). Use th...

Page 49 - PLAYBACK; PLAYBACK PROCEDURE; Figure 25. Playback Controls; Turn the JOG dial to select ON, and then turn the SHUTTLE ring right.

Pelco Manual C673M (2/01) 49 PLAYBACK PLAYBACK PROCEDURE Figure 25. Playback Controls 1. Load a pre-recorded tape. (Turn on the VCR and peripherals if you have not alreadydone so. If the erasure prevention tab has been removed, the VCR automaticallybegins playback mode.) 2. (Perform steps 2 through ...

Page 50 - Table H. Audio Playback and Picture Quality; END OF TAPE; Table I. End of Tape Actions; SPECIAL EFFECTS PLAYBACK

50 Pelco Manual C673M (2/01) PLAYBACK MODE • Pressing the REC/PLAY MODE button switches playback mode for the T-120 settingin the following order: 6H, L18H, L30H, 48H, 72H, 96H, 120H, 168H, 0H, 6H (for atape recorded in longer than 6H mode). For the T-160 setting, the order is: 8H, L24H,L40H, 64H, 9...

Page 51 - Figure 26. Shuttle Ring Speed Settings; DIRECT SHUTTLE RING; Figure 27. Direct Shuttle Ring Speed Settings

Pelco Manual C673M (2/01) 51 SHUTTLE RING You can set the playback speed using the SHUTTLE ring. 1. Press PAUSE during playback to get a still picture. 2. Turn the SHUTTLE ring right or left to get the playback speed you want. 3. Cancel by pressing PAUSE to get a still picture and then pressing it a...

Page 52 - Figure 29. Picture Quality Adjustment; To adjust during playback:; ADJUSTING PICTURE QUALITY; IF NOISE APPEARS

52 Pelco Manual C673M (2/01) ADJUSTING THE PICTURE DURING PLAYBACK TRACKING ADJUSTMENT If noise appears in the picture during playback, reverse/forward slow playback, fastplayback, reverse playback, frame playback, or field playback, you can reduce or eliminateit by adjusting the tracking. Figure 29...

Page 54 - SEARCH TECHNIQUES; COUNTER MEMORY STOP; Figure 31. Skip Search

54 Pelco Manual C673M (2/01) SEARCH TECHNIQUES COUNTER MEMORY STOP This feature rewinds a tape until the counter on the fluorescent display reaches 00000 andstops. (NOTE: When the counter indicates 00000, COUNTER MEMORY STOP on theSearch Function menu cannot be selected.) 1. Press the SEARCH button ...

Page 55 - INDEX SEARCH; To exit the Search Function menu without searching, press STOP.; HOW TO COUNT THE INDEX NUMBER; The maximum count of alarm recordings is; Figure 32. Index Searching

Pelco Manual C673M (2/01) 55 INDEX SEARCH The VCR automatically inserts an index signal at the beginning of each alarm recording, sothe start of each alarm can be located. During fast forwarding or rewinding, the VCR cansearch for an alarm index signal you have selected. When the VCR finds it, the V...

Page 56 - TIME AND DATE SEARCH; You can find a picture recorded at a specific date and time.

56 Pelco Manual C673M (2/01) TIME AND DATE SEARCH You can find a picture recorded at a specific date and time. 1. Press the SEARCH button enough times to highlight TIME DATE SEARCH on theSearch Function menu. The time and date search indicator (D) on the fluorescentdisplay lights. 2. Turn the SHUTTL...

Page 57 - ADDITIONAL FUNCTIONS AND FEATURES; The backup is for

Pelco Manual C673M (2/01) 57 ADDITIONAL FUNCTIONS AND FEATURES COUNTER TAPE COUNTER A five-digit counter indicates the relative position on the recorded portion of the tape. COUNTER RESET Press the COUNTER RESET button to reset the counter to 00000. COUNTER MEMORY The counter display is stored in me...

Page 58 - USING WITH A PC; ASSIGNING THE RS-S32C SETTINGS

58 Pelco Manual C673M (2/01) USING WITH A PC Refer to the Connecting the VCR to a PC and Connecting to a PC for Remote Control sections for information about connection, protocol, data communication settings, and cableconnections. ASSIGNING THE RS-S32C SETTINGS Assign the RS-232C interface board set...

Page 59 - Figure 33. Commands When Controlling One VCR; Example 1

Pelco Manual C673M (2/01) 59 COMMANDS FROM A PC This section covers the commands sent from the PC (or other equipment) to the VCR andthe VCR’s responses. WHEN CONTROLLING ONLY ONE VCR Set VCR ADDRESS in the RS-232C menu to NONE when controlling only one VCR via the PC. Command: Commands sent to the ...

Page 60 - WHEN CONTROLLING MULTIPLE VCRS; Figure 34. Commands When Controlling Multiple VCRs; Sending Commands

60 Pelco Manual C673M (2/01) WHEN CONTROLLING MULTIPLE VCRS Set VCR ADDRESS for each VCR in the RS-232C menu to different addresses (fromVCR01 to VCR255, except NONE). • When you want to control a specific VCR, enter its address (for example, VCR01) anda comma before entering the command code. • Whe...

Page 61 - Example 2; Command for recording

Pelco Manual C673M (2/01) 61 Example 2 Set the clocks to 12:27 on all the connected VCRs (when DELIMITER<SEND> andDELIMITER<RECEIVE> on the RS-232C menu are set to CR). Sending Commands Status or Error Code from Meaning from the PC, etc. the VCR to PC, etc. ALL,SC12,27 CR Command for rec...

Page 62 - COMMANDS AND RESPONSES CHART; The chart uses the following conventions:; Commands

62 Pelco Manual C673M (2/01) COMMANDS AND RESPONSES CHART The chart uses the following conventions: * An asterisk indicates a character or digit (for example, *** indicates three characters ordigits). #1 This means input the code according to the DELIMITER<RECEIVE> setting (CR[0DH] or CR [0DH]...

Page 67 - out

Pelco Manual C673M (2/01) 67 No. Commands Functions Status After Normal Explanation of Status Execution 99 SM*#1 Daylight saving setting RC#2EX#2 Command received and carried * : 0=OFF, 1=ON, 2=AUTO out 100 SM?#1 Inquiry about daylight saving setting RC#2SM*#2 * =0=OFF, 1=ON, 2=AUTO OFF,3=AUTO ON 10...

Page 68 - ERROR CODES; Error; TESTING; INITIAL SYSTEM TESTING

68 Pelco Manual C673M (2/01) ERROR CODES No. Error Meaning of Error 1 ER01 No power supply 2 ER02 No cassette loaded 3 ER03 Broken tape tab (unable to record) 4 ER04 Beginning of the tape 5 ER05 Tape end 6 ER06 Problem with the tape, video input, or VCR mechanism 7 ER07 Present time or timer program...

Page 69 - TROUBLESHOOTING; SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY; Table J. Warning Display and Actions

Pelco Manual C673M (2/01) 69 TROUBLESHOOTING SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY The VCR uses self-diagnostics to detect internal malfunctions during recording. If oneoccurs, the VCR indicates it on the fluorescent display and/or the monitor. Table J showsthe type of malfunction correspondi...

Page 70 - BEFORE CALLING FOR SERVICE; SYMPTOM

70 Pelco Manual C673M (2/01) BEFORE CALLING FOR SERVICE If you cannot solve your problem after checking the following list, stop using the VCR,unplug it from the outlet, and contact your dealer. SYMPTOM REMEDY INSTALLATION PROBLEMS No power at the VCR. • Is the power cord disconnected at the AC outl...

Page 72 - SPECIFICATIONS; ELECTRICAL

72 Pelco Manual C673M (2/01) SPECIFICATIONS ELECTRICAL Power Source: 100-230 VAC ± 10%, 50/60 Hz (the included power cord is used for 120 VAC, 60Hz) Power Consumption: Approximately 20 watts VIDEO AND AUDIO Tape Format: VHS, 1/2-inch width, high-density, video cassette tape Television System: EIA st...

Page 73 - Table K. Tape Speed and Recording Time

Pelco Manual C673M (2/01) 73 T-120Mode 6H (EP) L18H (EP)L30H (EP) 48H (EP)72H (EP)96H (EP) 120H (EP)168H (EP) 0H (EP) T-160Mode 8H (EP) L24H (EP)L40H (EP) 64H (EP)96H (EP) 128H (EP)160H (EP)224H (EP) 0H (EP) Time (hour:min) (T-120/T-160) 6:00/8:00 18:00/24:0030:00/40:0054:00/72:00 78:00/104:00 102:0...

Page 74 - INDEX; JOG dial operation 23

74 Pelco Manual C673M (2/01) INDEX A Adjusting the picture 52Alarm list 47Alarm recording 44 connection 14search 54, 55 Alarm recording connection 44Alarm recording duration 29Alarm recording mode 29Alarm start times 47Audio playback 50Audio recording 38 B Background color 27Blue back 27Buzzer 32 C ...

Page 76 - REVISION HISTORY; REGULATORY NOTICES; Reorient or relocate the receiving antenna.

REVISION HISTORY Manual # Date Comments C673M 2/01 Original version. ® Pelco, the Pelco logo, Spectra, Genex, Legacy, and PelcoVision are registered trademarks of Pelco. © Copyright 2001, Pelco. ™ Esprit and Camclosure are trademarks of Pelco. All rights reserved. REGULATORY NOTICES NOTE: This equip...