Pelco CCC5100H - Manuals - manualsarea.com

Page 2 - DOCUMENT; Refer to the enclosed CD for the following documentation:; MODELS; color filter array; UTO I; DC-Drive Auto Iris Lens Setup

2 C2910M-B-QS (2/06) This quick start guide describes how to install and configure the CCC5100H Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings. BEFO R E YOU BEGIN DOCUMENT A TION Refer to the enclosed CD for the fol...

Page 3 - DW; Refer to Figure 1 as you install the CCC5100H Series camera.

C2910M-B-QS (2/06) 3 H AR DW AR E Refer to Figure 1 as you install the CCC5100H Series camera. Figure 1. CCC5100H Connectors VIDEOCONNECTOR SERVICECONNECTOR SETUPBUTTONS MULTIFUNCTION(RJ45-10) CONNECTOR POWERCONNECTOR BACK FOCUSADJUSTMENT C/CS LENS AUTO IRISLENS CABLEAND CONNECTOR(OPTIONAL)

Page 4 - LENS; To mount the lens onto the camera:; MOUNT

4 C2910M-B-QS (2/06) LENS The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without an adapter. To mount the lens onto the camera: 1. Use clean, compressed air to remove any dust or ot...

Page 5 - CONNECTIONS; Multifunction Connector; LOW VOLT; Connect a video cable to the BNC connector on the back of the camera.; VIDEO FO; press and hold the top and center buttons to select NTSC, or

C2910M-B-QS (2/06) 5 CONNECTIONS The CCC5100H Series camera offers standard power and coax video connectors. To use the RJ45-10 multifunction connector that combines power, video, and control leads, refer to Multifunction Connector in the Installation/Operation manual. LOW VOLT A GE POWE R Connect 1...

Page 6 - SETUP MENUS

6 C2910M-B-QS (2/06) SETUP MENUS Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page: CAMERA DISPLAY CAMERA NAME CCC5100H RX ADDRESS 1 SAVE RX ADDRESS<DISPLAY PROPERTIES><GAMMA/SATURATION><GAIN CONTROL><SHARPNESS&...

Page 8 - CCESSING THE SETUP MENUS; Table; Rear Panel Buttons and Actions; ME; MENU

8 C2910M-B-QS (2/06) A CCESSING THE SETUP MENUS Use the top, center, and bottom buttons on the rear panel to access and navigate the setup menus. Table A lists the button presses for each menu action. A short press is less than one second; a long press is more than one second. Throughout the rest of...

Page 9 - WD

C2910M-B-QS (2/06) 9 C A ME RA P R OFILE Select a basic camera profile and then customize it. After you save your custom camera settings into a user-definable profile, change the default to CUSTOM1 or CUSTOM2. C A UTION: Be sure to save all camera settings into a user-definable profile so they will ...

Page 11 - Remove the lens from the camera.

C2910M-B-QS (2/06) 11 DC-D R IVE A UTO I R IS LENS SETUP Before using a DC-drive auto iris lens, you must adjust the DC offset setting. Use the following steps to match the camera’s DC voltage setting to the drive circuit on the auto iris lens: 1. Remove the lens from the camera. 2. Place the front ...

Page 12 - Open Iris and Closed Iris

12 C2910M-B-QS (2/06) 9. Hold the auto iris lens so you can watch the iris (refer to Figure 3). Then increase the DC OFFSET setting slowly until the iris closes. Figure 3. Open Iris and Closed Iris 10. As soon as the iris closes, slowly decrease the DC OFFSET value by 14, or until the iris opens aga...

Page 13 - LENS FOCUS; Focus the camera lens.

C2910M-B-QS (2/06) 13 LENS FOCUS Focus the camera lens. 1. A uto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter to open the iris fully. For best results, use an ND3 filter. 2. Manual iris only: Open the iris completely. 3. If necessary, enable automatic gain control ...

Page 14 - Fixed focal length lens only:

14 C2910M-B-QS (2/06) 6. Fixed focal length lens only: a. Set the lens focal length to far ( ∞ ). b. Adjust the back focus. Move the back focus locking screw on the camera up or down until the image is focused. As the focus improves, the value on the FINE FOCUS menu increases: the higher the number,...