Pelco CCC4000 - Manuals - manualsarea.com

Page 2 - CONTENTS; LIST OF TABLES

2 Pelco Manual C1925M (3/99) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 3 MODELS ..............

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; The product may bear the following marks:; DESCRIPTION; Electronic/Passive Iris Control; MODELS; NTSC format camera

Pelco Manual C1925M (3/99) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installationpersonnel. 2. Installation shall be done in accordance with ...

Page 4 - LOCATION OF PARTS AND CONTROLS; LOCKING RING; FRONT VIEW

4 Pelco Manual C1925M (3/99) LOCATION OF PARTS AND CONTROLS Figure 1. Location of Parts and Controls (Front and Rear) BACK-FOCUS LOCKING RING CS-MOUNT RING 1/3-INCH CCD ELEMENT IRIS CONNECTOR POWER CONNECTOR CAMERA MOUNT (1/4-20 UNC) VIDEO OUTPUT (BNC) V-PHASE ADJUSTMENT 4 2 3 1 PIN 1 = CONTROL COIL...

Page 5 - INSTALLATION; CAMERA MOUNTING; Figure 2. Camera Mounting Screw; Be

Pelco Manual C1925M (3/99) 5 INSTALLATION CAMERA MOUNTING Mount the camera using a 1/4–20 mounting screw that does not exceed .197" (4.5 mm ± .2 mm) in length (refer to Figure 2). An optional CA1750 Mount Adapter is supplied to attach the camera to a ceiling mount. To install the adapter (refer ...

Page 6 - POWER REQUIREMENTS; Model; POWER AND VIDEO CONNECTIONS; Table A. Video Coaxial Cable Requirements; Maximum Distance

6 Pelco Manual C1925M (3/99) POWER REQUIREMENTS An external power supply (not provided) is required when using CCC4000 Series cameras.This camera will accept either AC or DC power in accordance with the chart immediatelybelow. A safety ground terminal ( ) is provided on the connector block to connec...

Page 7 - Important Lens Notes:; LENS

Pelco Manual C1925M (3/99) 7 LENS INSTALLATION GENERAL LENS INFORMATION CCC4000 Series cameras are factory adjusted to the CS-mount standard. Fixed iris,manual iris, or passive (DC controlled) auto-iris lenses may be used. Passive (DCcontrolled) auto-iris lenses require a standard 4-pin square conne...

Page 8 - LENS MOUNTING; Remove the black protection cover from the CS-mounting ring.; BACK-FOCUS ADJUSTMENT; Fixed Focal Length Lenses; The iris cable of a

8 Pelco Manual C1925M (3/99) LENS MOUNTING Do not release the back-focus locking ring unnecessarily. Back-focus adjustment hasbeen set at the factory to the standard CS-mount back-focus distance. To mount a lens: 1. Remove the black protection cover from the CS-mounting ring. 2. If using a C-mount l...

Page 9 - Motorized Zoom Lenses; Using the camera controller, set the lens in the following manner:; CAMERA SYNCHRONIZATION AND V-PHASE; NTSC Standard

Pelco Manual C1925M (3/99) 9 b. Adjust the lens and the CS-mount ring together until picture is sharpest. c. Hold the lens and CS-mount ring in place and turn the back-focus lockingring clockwise to tighten. Motorized Zoom Lenses 1. With the camera operating, position the camera to view an object at...

Page 11 - SPECIFICATIONS; Pixels

Pelco Manual C1925M (3/99) 11 SPECIFICATIONS CCD Sensor: Color 1/3-inch interline transfer Pixels NTSC: 512 H x 492 V PAL: 512 H x 582 V Sensing Area: 4.7 x 3.5 mm (3/16 x 1/8 in.) Sync System: Free running/line lock (when AC powered) HorizontalResolution: 400 TV lines Lens Mount: CS mount Light Sen...

Page 12 - REVISION HISTORY; REGULATORY NOTICES; PRODUCT WARRANTY AND RETURN INFORMATION

12 Pelco Manual C1925M (3/99) REVISION HISTORY Manual # Date Comments C1925M 1/98 Original version. 3/99 Added CCC4001-2 model. Revised manual format. Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 1999, Pelco. Endura and ExSite a...