National Instruments NI 9229E - Manuals

National Instruments NI 9229E – Manual in PDF format online.

Manuals:

Manual

Manual National Instruments NI 9229E

Summary

Page 2 - Caution

NI 9229E/9239E 2 ni.com This document describes how to use the National Instruments 9229E and National Instruments 9239E and includes dimensions, terminal assignments, and specifications. In this document, the NI 9229E and NI 9239E are referred to inclusively as the NI 9229E /9239E. Visit ni.com/inf...

Page 3 - The following figure shows the dimensions of the NI 9229E /9239E.

© National Instruments Corp. 3 NI 9229E/9239E NI 9229E/9239E Dimensions The following figure shows the dimensions of the NI 9229E /9239E. Figure 1. NI 9229E /9239E Dimensions in Millimeters (Inches) 0.0 (0.00) 26.7 (1.05) 58.4 (2.30) 66.0 (2.60) 73.4 (2.89) 0.0 (0.00)

Page 5 - Note; You must use 2-wire ferrules to create a secure

© National Instruments Corp. 5 NI 9229E/9239E The NI 9229E /9239E has four 2-terminal detachable screw-terminal connectors. Note You must use 2-wire ferrules to create a secure connection when connecting more than one wire to a single terminal on the NI 9229E /9239E. You can connect ground-reference...

Page 8 - Passband

NI 9229E/9239E 8 ni.com Understanding NI 9229E/9239E Filtering The NI 9229E /9239E uses a combination of analog and digital filtering to provide an accurate representation of in-band signals while rejecting out-of-band signals. The filters discriminate between signals based on the frequency range, o...

Page 10 - Stopband; The frequency of a master timebase (

NI 9229E/9239E 10 ni.com Stopband The filter significantly attenuates all signals above the stopband frequency. The primary goal of the filter is to prevent aliasing. Therefore, the stopband frequency scales precisely with the data rate. The stopband rejection is the minimum amount of attenuation ap...

Page 11 - Specifications

© National Instruments Corp. 11 NI 9229E/9239E to control sampling, all of the modules must share a single master timebase source. Refer to the software help for information about configuring the master timebase source for the NI 9229E /9239E. Visit ni.com/info and enter cseriesdoc for information a...

Page 12 - Sleep Mode; and enter; for information about

NI 9229E/9239E 12 ni.com Sleep Mode This module supports a low-power sleep mode. Support for sleep mode at the system level depends on the chassis that the module is plugged into. Refer to the chassis manual for information about support for sleep mode. If the chassis supports sleep mode, refer to t...

Page 13 - Input Characteristics; channels

© National Instruments Corp. 13 NI 9229E/9239E Specifications The following specifications are typical for the range – 40 to 85 °Cinternal to any enclosures unless otherwise noted. All voltages are relative to the AI– signal on each channel unless otherwise noted. The specifications are the same for...

Page 14 - Module

NI 9229E/9239E 14 ni.com Data rate range ( f s ) using external master timebase Minimum .................................... 390.625 S/sMaximum ................................... 51.2 kS/s Data rates 1 ( f s ) .................................. , n = 1, 2, …, 31 Input voltage ranges (AI+ to AI–) Ov...

Page 15 - Measurement Conditions

© National Instruments Corp. 15 NI 9229E/9239E Accuracy, NI 9229E Measurement Conditions Percent of Reading (Gain Error) Percent of Range * (Offset Error) Calibrated max (– 40 to 70 °C) ±0.13% ±0.05% Calibrated typ (25 °C, ±5 °C) ±0.03% ±0.008% Uncalibrated max (– 40 to 70 °C) ±1.2% ±0.55% Uncalibra...

Page 16 - Input noise; Stability

NI 9229E/9239E 16 ni.com Accuracy, NI 9239E Input noise NI 9229E .................................... 320 μ V rms NI 9239E .................................... 70 μ V rms Stability Gain drift .................................... ±5 ppm/°COffset drift NI 9229E .............................. ±150 μ V/...

Page 17 - Input delay

© National Instruments Corp. 17 NI 9229E/9239E Post calibration gain match(ch-to-ch, 20 kHz)............................. 0.22 dB max Crosstalk (1 kHz) .............................. –130 dB Phase mismatch (ch-to-ch) NI 9229E .................................... 0.045°/kHz maxNI 9239E .................

Page 18 - Contact NI for Bellcore MTBF specifications

NI 9229E/9239E 18 ni.com Alias-free bandwidth ........................ 0.453 · f s –3 dB prefilter bandwidth( f s = 50 kS/s) ..................................... 24.56 kHz CMRR ( f in = 60 Hz) NI 9229E .................................... 116 dBNI 9239E .................................... 126 dB S...

Page 19 - Power Requirements; Power consumption from chassis; Physical Characteristics; For two-dimensional drawings and

© National Instruments Corp. 19 NI 9229E/9239E Power Requirements Power consumption from chassis Active mode ............................... 740 mW maxSleep mode ................................. 25 μ W max Thermal dissipation (at 70 °C) Active mode ............................... 760 mW maxSleep mo...

Page 20 - Safety; Isolation Voltages; Connect only voltages that are within the following limits.; dielectric withstand test

NI 9229E/9239E 20 ni.com Torque for screw terminals ............... 0.22 to 0.25 N · m (1.95 to 2.21 lb · in.) Ferrules ............................................. 0.25 mm 2 to 0.5 mm 2 Weight ............................................... 50 g (1.8 oz) Safety Isolation Voltages Connect only volt...

Page 21 - Do; Safety Standards; For UL and other safety certifications, refer to the

© National Instruments Corp. 21 NI 9229E/9239E Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V ...

Page 22 - Online Product Certification; , search by module number or product line, and; Environmental; noncondensing

NI 9229E/9239E 22 ni.com Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/ certification , search by module number or product line, and click...

Page 23 - Environmental Management; For additional environmental information, refer to the; Waste Electrical and Electronic Equipment (WEEE); EU Customers; At the end of the life cycle, all products

© National Instruments Corp. 23 NI 9229E/9239E Maximum altitude............................. 2,000 m Pollution Degree (IEC 60664) .......... 2 Environmental Management National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes th...

Page 24 - Calibration; ⬉ᄤֵᙃѻક∵ᵻ᥻ࠊᄣ⧚ࡲ⊩ ˄Ё೑; RoHS; National Instruments; about China RoHS compliance, go to

NI 9229E/9239E 24 ni.com Calibration You can obtain the calibration certificate and information about calibration services for the NI 9229E/9239E at ni.com/ calibration . Calibration interval ........................... 1 year ⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS ˅ Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃ ѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽...

Page 25 - Where to Go for Support; you have access to

© National Instruments Corp. 25 NI 9229E/9239E Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance...