National Instruments CFP-2220 - Manuals

cFP-2200/2210/2220 10 ni.com Mounting the Backplane in a Standard 19 in. Rack The rack-mount kit for Compact FieldPoint is NI part number 778615-01. The following figure shows the dimensions of the rack-mount kit. Figure 15. Dimensions of Rack-Mount Kit Complete the following steps to mount the syst...

© National Instruments Corporation 13 cFP-2200/2210/2220 Installing the cFP-22 xx on the Backplane 1. Make sure that no power is connected to the controller. 2. Make sure that the controller is right side up with the NI logo at the top, and align the captive screws on the controller with the holes o...

cFP-2200/2210/2220 14 ni.com Installing I/O Modules on the Backplane 1. Align the captive screws on the I/O module with the holes on the backplane. 2. Press firmly to seat the I/O module on the backplane. 3. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) length, tight...

© National Instruments Corporation 15 cFP-2200/2210/2220 Installing Connector Blocks on the Backplane In order to connect I/O modules to input signals or loads, you need to install a cFP-CB- x connector block or other connectibility accessory for each I/O module on the backplane. Use the connector s...

© National Instruments Corporation 17 cFP-2200/2210/2220 Connecting the cFP-22 xx to a Network Connect the cFP-22 xx to an Ethernet network using RJ-45 Ethernet port 1 on the controller front panel. Use a standard Category 5 (CAT-5) or better Ethernet cable to connect the controller to an Ethernet h...

cFP-2200/2210/2220 18 ni.com Wiring Power to the cFP-22 xx The cFP-22 xx requires an external power supply that meets the specifications in the Power Requirements section. The cFP-22 xx filters and regulates the supplied power and provides power for all of the I/O modules. You must connect a power s...

cFP-2200/2210/2220 20 ni.com Note The controller indicates which terminal it is using on the channel called Power Source in software. A value of 0 indicates V2, and a value of 1 indicates V1. This behavior is different from that of older Compact FieldPoint controllers. If your application uses input...

© National Instruments Corporation 23 cFP-2200/2210/2220 Figure 27 shows how to wire several FP-1001 banks in an RS-485 network controlled by the cFP-2220. Only two FP-1001 banks are shown, but the cFP-2220 can control up to 24 FP-1001 banks. Install 120 Ω termination resistors at each end of the ne...

cFP-2200/2210/2220 24 ni.com You can use the two digital inputs to control the cFP system from LabVIEW. For example, one input could be a START/STOP switch, and the other could determine which of two VIs should run at startup. NI recommends connecting a single-pole single-throw (SPST) switch between...

© National Instruments Corporation 25 cFP-2200/2210/2220 Configuring DIP Switches Figure 29. DIP Switches All of the DIP switches are in the OFF position when the controller is shipped from National Instruments. IP RESET Switch Push the IP RESET switch to the ON position and reboot the controller to...

cFP-2200/2210/2220 26 ni.com NO APP Switch Push the NO APP switch to the ON position to prevent a LabVIEW RT startup application from running at startup. If you want to permanently disable a LabVIEW RT application from running at startup, you must disable it in LabVIEW. To run an application at star...

© National Instruments Corporation 27 cFP-2200/2210/2220 Using the Reset Button Pressing the Reset button resets the processor in the same manner as cycling power. Understanding LED Indications Figure 30. LEDs STATUS LED The STATUS LED is off during normal operation. The cFP-22 xx indicates specific...

cFP-2200/2210/2220 28 ni.com POWER LED The POWER LED is lit while the cFP-22 xx is powered on. This LED indicates that the power supply connected to the controller is adequate. The POWER LED lights green when the controller is using the primary power supply and amber when the controller is using the...

© National Instruments Corporation 29 cFP-2200/2210/2220 Remote Front Panels You may need to monitor and control an embedded VI remotely. The cFP-22 xx supports multiple remote front panels for embedded VIs. Users can view the remote front panel using either LabVIEW or a Web browser. Users accessing...

cFP-2200/2210/2220 30 ni.com Troubleshooting This section contains troubleshooting instructions for the cFP-22 xx and FieldPoint software. For more troubleshooting information, refer to the Measurement & Automation Explorer Help for FieldPoint and the Measurement & Automation Explorer Remote...

© National Instruments Corporation 31 cFP-2200/2210/2220 Specifications The following specifications are typical for the – 40 to 70 °C operating temperature range unless otherwise noted. Network Network interface ................................... 10BaseT and 100BaseTX Ethernet Compatibility .........

cFP-2200/2210/2220 32 ni.com RS-232 (DTE) serial ports Maximum baud rate.........................115,200 bps Data bits ...........................................5, 6, 7, 8 Stop bits ...........................................1, 1.5, 2 Parity................................................Odd, Even,...

© National Instruments Corporation 33 cFP-2200/2210/2220 Physical Characteristics If you need to clean the controller, wipe it with a dry towel. Screw-terminal wiring............................ Use copper conductor wire with 10 mm (0.39 in.) of insulation from the ends. External digital I/O termina...

cFP-2200/2210/2220 34 ni.com Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control, and laboratory use: • EN 61326 EMC requirements; Industrial Immunity • EN 55011 Emissions; Group 1, Class ...

© National Instruments Corporation 35 cFP-2200/2210/2220 Environmental The cFP-22 xx is intended for indoor use only, but it may be used outdoors if mounted in a suitably rated enclosure. Operating temperature(IEC 60068-2-1, IEC 60068-2-2) ........... – 40 to 70 °C Note To meet this operating temper...

cFP-2200/2210/2220 36 ni.com Cabling Table 4 shows the standard Ethernet cable wiring connections for both normal and crossover cables. Figure 31. Ethernet Connector Pinout Table 4. Ethernet Cable Wiring Connections Pin Connector 1 Connector 2 (Normal) Connector 2 (Crossover) 1 white/orange white/or...

© National Instruments Corporation 37 cFP-2200/2210/2220 Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone ...