Metra 99-8214TB - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; NOWLEDGE IS

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4,5,6 Final Assembly . . . . . . ....

Page 3 - DASH DISASSEMBLY; Continue to Kit Preparation.

99-8214 1 Disconnect the negative battery terminal to prevent an accidentalshort circuit. 1 Unclip and remove A/C control panel. (Figure A) 2 TOYOTA TACOMA 2005-2011 Remove (4) 10 MM bolts securingradio. (Figure B) 3 Unclip and remove entire panelincluding hazard switch and clock. (Figure C) 4 Remov...

Page 4 - KIT PREPARATION; Continue to Kit Assembly.; (SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO)

2 99-8214 TACOMA 2005-2011 KIT PREPARATION Clip the clock/hazard switch assembly into the 99-8214 RadioHousing Trim Panel. (Figure A,B) 2 A H M PASSENGER PASSENGER INSERT CLOCK/HAZARD SWITCH ASSEMBLY FROM REAR OF 99-8214 RADIO HOUSING TRIM PANEL H M PASSENGER PASSENGER B Continue to Kit Assembly. At...

Page 5 - KIT ASSEMBLY; DIN HEAD UNIT PROVISION; Continue to Final Assembly.

99-8214 KIT ASSEMBLY TOYOTA TACOMA 2005-2011 Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs down. (Figure B) 2 Slide the aftermarket head unit intothe cage and secure. (Figure C) 3 Secure the Radio Housing into thedash using the factory hardware. 4 DIN HEAD UNIT...

Page 6 - ISO DIN HEAD UNIT PROVISION

99-8214 KIT ASSEMBLY TOYOTA TACOMA 2005-2011 Attach the corresponding radio housing bracket to the radio housingusing the included (4) #8 x 3/8”Phillips truss head screws. (Figure A) 1 Mount the ISO Brackets to the headunit with the screws supplied withthe unit. (Figure B) 2 Slide the head unit into...

Page 7 - DOUBLE DIN HEAD UNIT PROVISION

5 Slide the aftermarket radio unit intothe factory brackets and secure theunit to the brackets using thescrews supplied with the head unit. (Figure A) 1 A B REMOVE CLOCK/HAZARD SWITCH BRACKET ASSEMBLY REMOVE CLOCK/HAZARD SWITCH BRACKET ASSEMBLY REAR VIEW OF RADIO HOUSING D RESTORECLOCK/HAZARD SWITCH...

Page 8 - STACKED ISO DIN HEAD UNIT PROVISION

6 Slide the aftermarket radio units intothe factory brackets and secure theunit to the brackets using thescrews supplied with the head unit. (Figure A) 1 Secure the aftermarket radio unitsand factory bracket assembly intothe sub dash. (Figure B) 2 STACKED ISO DIN HEAD UNIT PROVISION 99-8214 KIT ASSE...

Page 9 - Twist ends together; FINAL ASSEMBLY; When Black a wire is not present, ground radio to vehicle chassis.; METRA / EIA WIRING CODE

7 FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal...

Page 10 - NOTES