Metra 95-2009 - Manuals - manualsarea.com

Page 2 - VEHICLE APPLICATION CONTENTS; Dash Disassembly

BUICK Century 1997-2005 3 Le Sabre 1995-2005 4 Park Avenue 1995-2005 5 Rainier 2004-2007 28 Regal 1995-2004 3 Rendezvous 2002-2007 6 Riviera 1996-1999 7 Roadmaster 1995-1996 8 Skylark 1996-1998 9 CADILLAC Escalade/EXT 2003-2006 10 Fleetwood/Broughham 1990-1996 11-12 Eldorado 1992-1995 13Seville 1992...

Page 3 - Continue to kit assembly

95-2009 DASH DISASSEMBLY BUICK • CENTURY 1997-2005 / REGAL 1995-2004 3 1 Unsnap the top edge of the knee bolster panel. Disconnect the negative battery terminal to prevent an accidentalshort circuit. 3 Remove the plastic trim piece to theleft of the glove box and (1) Phillipsscrew exposed. 2 Remove ...

Page 9 - ontinue to kit assembly

9 95-2009 DASH DISASSEMBLY 1 Under glove box and drivers knee bol-ster, remove (2) plastic panels by turning (2) 1/4 turn fasteners per side. Disconnect the negative battery terminal to prevent an accidentalshort circuit. 3 Remove (6) 9/32" screws inside glovebox. 2 Remove (4) 9/32" screws r...

Page 11 - CADILLAC •; FLEETWOOD

11 95-2009 DASH DISASSEMBLY 1 Remove (2) 7mm screws at the top of the radio/air conditioning bezel, then unclip panel and remove. Disconnect the negative battery terminal to prevent an accidental short circuit. 3 Carefully unsnap trim panel above a/c controls. 2 Remove (4) 7mm screws that hold the r...

Page 13 - Use

13 95-2009 DASH DISASSEMBLY 1 1 Gently pry up on the ashtray/gearshifter trim bezel and remove. (CAUTION: Some models areequipped with bezels made of realwood. Disconnect the negative battery terminal to prevent an accidentalshort circuit. 3 Using a panel removal tool, pry out onthe radio trim ring ...

Page 26 - OLDSMOBILE • SILHOUETTE 2000

26 95-2009 DASH DISASSEMBLY 1 Remove (1) Phillips screw from thecigarette lighter compartment. Disconnect the negative battery terminal to prevent an accidentalshort circuit. 3 Remove the ashtray and (1) phillipsscrew exposed in the ashtray cavity. 2 Remove (2) Phillips screws securingthe factory he...

Page 36 - Unclip the radio trim bezel and remove.; OLDSMOBILE •

36 95-2009 DASH DISASSEMBLY OLDSMOBILE • EIGHTY EIGHT 1994-1999 1 Remove (2) ) 9/32" hex-head screws securing the factory head unit and disconnectthe wiring. Disconnect the negative battery terminal to prevent an accidental short circuit. 3 Unclip the radio trim bezel and remove. 2 Continue to k...

Page 46 - GM; vehicles; CHEVY; Tracker; CADILLAC; Continued on page 46

46 95-2009 TAB INSTRUCTIONS CHEVY/GM/METRO/SUZUKI CADILLAC-FLEETWOOD/BROUGHAM * Note: Refer also to the instructions included with the aftermarket radio. GM vehicles . Cut tabs highlighted on both sides ofboth brackets. (Figure A) 1 CHEVY Tracker /METRO/SUZUKI. Cut tabs highlighted on both sides ofb...

Page 47 - ISUZU; TOYOTA; Cut tabs highlighted.; Continue to final assembly

47 95-2009 TAB INSTRUCTIONS ISUZU-PONTIAC/TOYOTA/ CADILLAC-ELDORADO/SEVILLE ISUZU Amigo/Rodeo/Rodeo Sport. Cut tabs highlighted. (Figure D) 4 TOYOTA Matrix/ PONTIAC Vibe. Cut tabs highlighted. (Figure E) Cut (4) tabs highlighted on double DIN trim plate. (Figure H) 5 CADILLAC Eldorado/Seville. Cut t...

Page 48 - KIT ASSEMBLY WITH FACTORY BRACKETS

48 95-2009 KIT ASSEMBLY TOP FACTORY BRACKET BOTTOM FACTORY BRACKET 1 Using carriage bolts and Keps nuts supplied, mount the factory brackets to thedouble DIN trim plate/double DIN bracket assembly, keeping in mind whichbracket is top and which one is bottom. CADILLAC • FLEETWOOD FLEETWOOD BROUGHAM 1...

Page 50 - DOUBLE DIN RADIO PROVISION; For the Buick Le Sabre,

50 95-2009 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNIT(S) PROVISION Snap the Double DIN brackets to theedge of the Double DIN trim plate. (Figure A) 1 Slide the Double DIN head unit orstacked ISO head units into the brack-et/radio housing assembly and securethe Double DIN head uni...

Page 51 - FINAL ASSEMBLY; B) Twist ends together; FINAL WIRING CONNECTIONS; METRA / EIA WIRING CODE

95-2009 FINAL ASSEMBLY FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape A B C D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of an...