Metra 99-2005 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS

• Dash Disassembly - Cadillac Eldorado 1996-2002------------------------------------- 1 - Cadillac Seville 1996-1997--------------------------------------- 1 - Cadillac Seville 1998-2005--------------------------------------- 2 - Cadillac Deville 2000-2005--------------------------------------- 3 - ...

Page 3 - CADILLAC ELDORADO; DASH DISASSEMBLY

1 Disconnect the negative battery ter-minal to prevent an accidental shortcircuit. Remove C-clip on forward facing side ofshift knob and pull and remove knob. (Figure A) 1 2 Remove (2) 9/32 screws on each side ofthe ashtray assembly and (1) in the mid-dle underneath ashtray insert. (Figure B) 3 Remo...

Page 4 - CADILLAC DEVILLE CONCOURS

2 Disconnect the negative battery ter-minal to prevent an accidental shortcircuit. Insert a small flat blade screwdriver inbetween the radio and the switch panelat top of radio and pry up and out toremove switch panel . (Figure B) 1 3 Remove (3) 9/32 screws• (1) from the top (Figure C) and • (2) fro...

Page 6 - KIT ASSEMBLY

4 99-2005 KIT ASSEMBLY Remove all tabs except the ones marked S-E from the radio housing. ( Figure A) Slide the climate control assembly intothe bracket / housing assembly andattach with the factory hardware. (Figure C) 1 3 Slide the S-E radio housing bracket onto the 99-2005 until side clips engage...

Page 7 - CADILLAC SEVILLE

5 99-2005 KIT ASSEMBLY S-E S-E D D D D 98-04 S 98-04 S 98-04 S A B C D Slide the climate control assembly intothe bracket / housing assembly andattach with the factory hardware. (Figure C) 3 When DIN mounting slide the includedspacer onto the DIN cage that came withyour aftermarket radio before inse...

Page 8 - CADILLAC DEVILLE

6 99-2005 KIT ASSEMBLY CADILLAC DEVILLE 2000-2005 NOTE: In order to DIN mount in the 2000-2004 Deville you will need to use the provided spacer as described below. There is not enough depth to ISO mount or DIN mount withoutthe spacer. S-E S-E D D D D 98-04 S 98-04 S 98-04 S A B C Remove all tabs exc...

Page 9 - DIN HEAD UNIT PROVISION

7 DIN HEAD UNIT PROVISION 99-2005 KIT ASSEMBLY NOTE: Refer also to the instructions included with the aftermarket radio. 2 1 Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs down. (Figure A) Slide the after-market head unit intothe cage and secure. (Figure B) A B ...

Page 10 - ISO DIN HEAD UNIT PROVISION

8 ISO DIN HEAD UNIT PROVISION 99-2005 KIT ASSEMBLY NOTE: Refer also to the instructions included with the aftermarket radio. 2 Snap the Trim plate into the RadioHousing. (Figure B) 1 Mount the ISO brackets to the after-market radio with the screws supplied with the unit. (Figure A) Slide the after-m...

Page 11 - FINAL ASSEMBLY; METRA / EIA WIRING CODE

9 FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.) 2 Re-connect the...

Metra 99-2005 - Manual

Table of Contents:

Summary

Other Metra Models