Makita DTW 1001 Z - Manuals

Page 2 - SPECIFICATIONS; Symbols; Intended use; Noise; Vibration

2 ENGLISH SPECIFICATIONS Model: DTW1001 DTW1002 DTW800 Fastening capacities Standard bolt M12 - M30 M12 - M24 High tensile bolt M10 - M24 M10 - M22 Square drive 19 mm 12.7 mm – Drive shank – 11.1 mm Hex. No load speed Impact mode (Hard) 0 - 1,800 min -1 Impact mode (Medium) 0 - 1,000 min -1 Impact m...

Page 3 - EC Declaration of Conformity; General power tool safety warnings; Save all warnings and instruc-; spheres, such as in the presence of flammable

3 ENGLISH Model DTW1002 Work mode: impact tightening of fasteners of the maxi - mum capacity of the tool Vibration emission (a h ) : 18.0 m/s 2 Uncertainty (K) : 1.5 m/s 2 Model DTW800 Work mode: impact tightening of fasteners of the maxi - mum capacity of the tool Vibration emission (a h ) : 24.0 m...

Page 4 - Cordless impact wrench safety; SAVE THESE INSTRUCTIONS.; Important safety instructions for

4 ENGLISH jewellery or long hair can be caught in moving parts. 7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Power tool use and care 1. Do not force th...

Page 5 - flow, overheating, possible burns and even a; FUNCTIONAL; Installing or removing battery; tridge firmly when installing or removing battery; Battery protection system

5 ENGLISH result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical atten- tion right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the termina...

Page 6 - Indicating the remaining battery; Switch action; Before inserting the battery car-; Lighting up the front lamp; Do not look in the light or see the

6 ENGLISH Lithium-ion batteries with a star marking are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: Overl...

Page 7 - Reversing switch action

7 ENGLISH 1 ► 1. Button To turn on the lamp status, press the button for one second. To turn off the lamp status, press the but - ton for one second again. With the lamp status ON, pull the switch trigger to turn on the lamp. To turn off, release it. The lamp goes out approximately 10 seconds after ...

Page 8 - Specifications of each impact force grade; ASSEMBLY; Selecting correct impact socket; Installing or removing impact socket

8 ENGLISH You can change the impact in three steps: hard, medium and soft mode. This allows a tightening suitable to the work.Every time the button is pressed, the number of blows changes in three steps. For approximately one minute after releasing the switch trigger, the impact force can be changed...

Page 9 - For impact socket without O-ring

9 ENGLISH For impact socket without O-ring and pin 1 2 ► 1. Impact socket 2. Square drive Align the square of the impact socket with the square drive and push the impact socket onto the square drive until it locks into place. Tap it lightly if required. To remove the impact socket, simply pull it of...

Page 10 - Ring; Before using the ring, always; Installing hook; OPERATION; Always insert the battery cartridge

10 ENGLISH Ring Only for Model DTW800 2 1 3 ► 1. Bracket 2. Ring 3. Screws The ring is convenient for hanging the tool with hoist. First, place the rope through the ring. Then hang the tool up to the air with hoist. CAUTION: Before using the ring, always make sure that the bracket and ring are secur...

Page 11 - Proper fastening torque for high tensile bolt

11 ENGLISH Model DTW1001 Proper fastening torque for standard bolt 1 2 N•m (kgf•cm) 800 600 400 200 (2040) (4080) (6120) (8160) 1 0 2 3 0 M24(1″) M24(1″) M30(1-1/4″) M30(1-1/4″) 1. Fastening time (second) 2. Fastening torque Proper fastening torque for high tensile bolt 1 0 2 3 4 5 6 0 800 600 400 2...

Page 12 - MAINTENANCE

12 ENGLISH Model DTW800 Proper fastening torque for standard bolt N•m (kgf•cm) 1 1 0 2 3 0 400 200 (2040) (4080) M20(3/4″) M20(3/4″) M24(1″) M24(1″) 2 1. Fastening time (second) 2. Fastening torque Proper fastening torque for high tensile bolt 1 0 2 3 4 5 6 0 800 600 400 200 (2040) (4080) (6120) (81...

Page 13 - These accessories or attachments

OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any a...