Jet 723510 - Manuals

6 4.0 Specifications Table 1 Model number JWDS-1020 Stock number 723510 Motor and Electricals Drum motor type Totally enclosed, fan-cooled induction Horsepower 1 HP (0.75 kW) Phase 1 Voltage 115 V Cycle 60 Hz Listed FLA (full load amps) 8 A Motor speed 1720 RPM Starting amps 34.5 A Running amps (no ...

8 Read and understand the entire contents of this manual before attempting set-up or operation. Failure to comply may cause serious injury. 5.0 Setup and assembly Open box and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Any missing parts should be...

9 Figure 5-4 3. Release fastener lever to secure end of strip. 4. Begin wrapping abrasive around drum. The tapered edge of strip end should follow as closely as possible to edge of drum. 5. Continue to wrap abrasive in spiral fashion by rotating drum with one hand and guiding strip with the other. S...

10 Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Failure to comply may cause serious or fatal injury. Use only 3-wire extension cords that have 3-prong grounding plugs a...

11 Figure 7-1: depth scale adjustment 7.3 Conveyor belt tension/tracking Conveyor belt tension adjustment may be necessary during the break-in period to compensate for belt stretching, and also after long-term use. 7.3.1 Belt tension adjustment NOTE: Insufficient belt tension will cause slippage of ...

12 6. If drum does not contact gauge equally on both ends of drum, alignment is needed. 7.4.1 Performing drum alignment To align conveyor table with drum: 1. Loosen both table locking screws (C, Figure 7- 3) with 5mm hex wrench. Loosen both table locking screws before adjusting drum alignment. Failu...

13 8.2 Switch safety key To prevent unauthorized use of sander, turn off main switch and pull out safety key (Figure 8-1). Store key in a safe place. Key must be reinserted to start sander. Figure 8-1: control panel 8.3 Circuit breaker reset If the sander becomes overloaded, the built-in breaker wil...

14 8.6 Maximum performance tips The versatility designed into the JWDS-series drum sander allows it to be used for a variety of tasks that will boost return on your investment. For example, it will speed up fine sanding work often done with slower, dust-generating hand sanders, and will achieve fine...

15 9.0 User-maintenance Before doing maintenance on the machine, disconnect it from the electrical supply (pull out the plug), unless indicated otherwise. Failure to comply may cause serious injury. 9.1 Cleaning and lubrication For best results, make cleaning the sander a regular shop procedure. All...

16 Note: If conveyor belt continually tracks to one side of the machine, reversing the belt on the conveyor table may remedy the problem. To make sure the conveyor table is not twisted, place a level on the conveyor table. Level the machine if needed. If there is still a problem, proceed with the st...

17 10.0 Abrasives The abrasive material you choose will have a substantial effect on the performance of your sander. Variations in paper type, weight, coating and durability all contribute to achieving your desired finish. JET Abrasives are available in Ready-To-Wrap TM pre-cut lengths or in the con...

18 11.0 Troubleshooting JWDS-series Drum Sander Symptom Possible Cause Correction * Drum motor won’t start when switch is activated. No incoming current. Check connections at plug or circuit panel. Safety key missing from switch. Install safety key. Low voltage. Check power line for proper voltage. ...

22 13.1.2 JWDS-1020 Drum Sander Parts List Index No Part No Description Size Qty 1 ................ TS-1503041 .............. Socket Head Cap Screw ......................................... M6 x 1.0P x 16L ........... 2 2 ................ JWDS1632-103 ......... Drum Carriage Hinge .....................

24 14.0 Electrical Connections for JWDS-1020 GM - GM + S anding M otor Bel t Motor L1 L2 Circuit B oard Overload R el ay Sw itc h Motor Shroud

25 15.0 Warranty and service JET ® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time p...