Jacuzzi J-SHOWER TOWERTM - Manuals

Jacuzzi J-SHOWER TOWERTM – Manual in PDF format online.

Manuals:

Manual

Manual Jacuzzi J-SHOWER TOWERTM

Summary

Page 5 - EXPLODED VIEW OF J-SHOWER TOWER

3 EXPLODED VIEW OF J-SHOWER TOWER END CAP SEE P AGE 20 BOTT OM RAIL SEE P AGE 15 & 16 SET SCREW SEE P AGE 16 PINS SEE P A GE 1 1 F A C EPL A T E SEE P AGE 21 MIXER/DIVERTER (INCLUDING HOSE CONNECTIONS) SEE P AGES 10 & 1 1 FILL SPOUT SEE P AGE 8

Page 8 - STANDOFF

6 Shower Tower HardwareIdentification Chart PLUMBING HARDWARE The diagrams for these fasteners are shown actual size for fast identification. FIBER WASHER .75 O.D. WASHER QTY.-2 SCREW QTY.-6 PHILLIPS HEADSCREW M4X12STAINLESS STEEL P3 WASHER QTY.-3 EXTERNAL TOOTHLOCK WASHER M4 WASHER QTY.-6 NIPPLE QT...

Page 9 - TOWER ASSEMBLY; ILLUSTRATION 1; BAIL; H1 BOLT

7 TOWER ASSEMBLY 1. Assemble the four (4) bails to the tower wall. Do not overtighten the nuts on the threadedshaft end. Overtightening may break the stud. ILLUSTRATION 1 BAIL SET SCREW (8) BOLT (8) H1 SHELF NUT (8) H2 H3 WASHER (8) H1 BOLT QTY.-8 SLOTFASTENER10 X32 H2 NUT QTY.-8 HEX NUT10 x 32 H3 S...

Page 10 - Attach the water inlet and fill spout to the; FILL SPOUT

8 2. Attach the water inlet and fill spout to the tower wall. (See Illustration 2 and 2a.) ILLUSTRATION 2a FILL SPOUT NUT QTY.-1 W2 LOCKNUT1/2"-14NPT FIBER WASHER1.24 DIA WASHER QTY.-1 W1 WATER INLET ILLUSTRATION 2 NIPPLE QTY.-1 P5 NUT CAULK WASHER WATERINLET TOWER WALL W2 W1 P6 CAULK P7 FILL SP...

Page 11 - Attach the wallbar assembly to the tower wall.; CAP; PARTS NOT NEEDED

9 3. Attach the wallbar assembly to the tower wall. (See Illustration 3.) ILLUSTRATION 3 FLATHEADSCREW#10-24 x 2 1/2"STAINLESSSTEEL EXTERNAL TOOTHWASHER 1/8" BEAD OF CAULK WALLBAR STAND-OFF WB4 CAP SIDE VIEWOF WALLBAR WALLBAR SHOWER HEADBRACKET SOAPDISH SHOWERWALL KEPNUT FLATWASHER SCREW WB3...

Page 14 - TOWER INSTALLATION; TAPE FIRMLY

12 ILLUSTRATION 9 (LEFT HAND SHOWN) 1. Locate the drilling template. Place it over the bathtub. The inner orange circle must be centered over the circular opening of the bathtub. (See Illustration 9.) Be sure the orange circle is spaced an equal distancearound the bath cavity. The line marked back w...

Page 15 - ILLUSTRATION 10; DISASSEMBLY INSTRUCTIONS; COUPLING

13 ILLUSTRATION 10 3. Attach Hot and Cold water supply lines of the mixer/diverter to the stub-out supply lines. (See Illustration 10.) 4. Locate the on/off handle and temporarily place it on the mixer valve. (See Illustration 26.) With the mixer/ diverter valve in the OFF position, turn on the wate...

Page 16 - PLACING TOWER; ILLUSTRATION 11; Clean off excess sealant.

14 PLACING TOWER ILLUSTRATION 11 5. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will set. (See Illustration 11.) 6. Place the tower pins in the holes and push the tower down firmly. The tow...

Page 17 - Locate the bottom rail and the fixed panel. Lay a bead; MUST DRILL AT 15; LOCATED IN HARDWARE KIT; FIXED PANEL

7. Locate the bottom rail and the fixed panel. Lay a bead of sealant on the bottom of the fixed panel. Secure thebottom rail to the fixed panel. (See Illustration 12.) Drilla 3/32" diameter hole into the bottom rail at about 15 ° . Drill only through the first aluminum thickness. (SeeIllustratio...

Page 18 - GENTLY

16 FIXED PANEL ASSEMBLE TO BATH 8. Screw 1-1/2" Allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the vertical frame. Place the assembly against the vertical edge of the tower and onto thebath surface. (See Illustrat...

Page 20 - DRILLING TOP RING; MUST DRILL AT A 15

18 11. Drill a 3/32" diameter hole into the top ring at about 15 ° . (See Illustration 20.) Engage the top of the fixed panelwith the top ring groove. Secure the top of the fixedpanel to the top ring. (See Illustration 21.) 12. Plumb and square the tower. Mark a point through each slot of the wa...

Page 21 - FIXED GLASS FRAME ATTACHMENT; ILLUSTRATION 23

19 FIXED GLASS FRAME ATTACHMENT 13. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. ILLUSTRATION 23 SEALANT FIXEDGLASS ENDEXTRUSION

Page 22 - OR; ILLUSTRATION 24; SCREW; LOCATED IN HARDWARE PACK

20 14. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws. Seal the end cap and place into the end of the lower track. Secure with self taping screw. (See Illustration24.) CAULK BACKWALL WALL END CAP F-EXTRUSION CAULK WALL L-EXTRUSI...

Page 24 - ILLUSTRATION 28; SHOWER HOSE

2I. Attach the shower hose. (See Illustration 27.)Use the washer supplied with the showerhose. 22. For hot and cold operation of the handle, see Illustration 28. HOT COLD HANDLE OPERATION ILLUSTRATION 28 OFF HAND HELDSHOWER WASHER TOWER WALL FLEX HOSE WASHER TEFLONTAPE WATERCONNECTOR WALL BAR ILLUST...

Page 28 - Jacuzzi Whirlpool Bath National Headquarters

Printed in the U.S.A. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type.It is the responsibility ...