Jacuzzi J-SHOWER TOWERTM - Manual

8 2. Attach the water inlet and fill spout to the tower wall. (See Illustration 2 and 2a.) ILLUSTRATION 2a FILL SPOUT NUT QTY.-1 W2 LOCKNUT1/2"-14NPT FIBER WASHER1.24 DIA WASHER QTY.-1 W1 WATER INLET ILLUSTRATION 2 NIPPLE QTY.-1 P5 NUT CAULK WASHER WATERINLET TOWER WALL W2 W1 P6 CAULK P7 FILL SP...

9 3. Attach the wallbar assembly to the tower wall. (See Illustration 3.) ILLUSTRATION 3 FLATHEADSCREW#10-24 x 2 1/2"STAINLESSSTEEL EXTERNAL TOOTHWASHER 1/8" BEAD OF CAULK WALLBAR STAND-OFF WB4 CAP SIDE VIEWOF WALLBAR WALLBAR SHOWER HEADBRACKET SOAPDISH SHOWERWALL KEPNUT FLATWASHER SCREW WB3...

12 ILLUSTRATION 9 (LEFT HAND SHOWN) 1. Locate the drilling template. Place it over the bathtub. The inner orange circle must be centered over the circular opening of the bathtub. (See Illustration 9.) Be sure the orange circle is spaced an equal distancearound the bath cavity. The line marked back w...

13 ILLUSTRATION 10 3. Attach Hot and Cold water supply lines of the mixer/diverter to the stub-out supply lines. (See Illustration 10.) 4. Locate the on/off handle and temporarily place it on the mixer valve. (See Illustration 26.) With the mixer/ diverter valve in the OFF position, turn on the wate...

14 PLACING TOWER ILLUSTRATION 11 5. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will set. (See Illustration 11.) 6. Place the tower pins in the holes and push the tower down firmly. The tow...

7. Locate the bottom rail and the fixed panel. Lay a bead of sealant on the bottom of the fixed panel. Secure thebottom rail to the fixed panel. (See Illustration 12.) Drilla 3/32" diameter hole into the bottom rail at about 15 ° . Drill only through the first aluminum thickness. (SeeIllustratio...

16 FIXED PANEL ASSEMBLE TO BATH 8. Screw 1-1/2" Allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the vertical frame. Place the assembly against the vertical edge of the tower and onto thebath surface. (See Illustrat...

18 11. Drill a 3/32" diameter hole into the top ring at about 15 ° . (See Illustration 20.) Engage the top of the fixed panelwith the top ring groove. Secure the top of the fixedpanel to the top ring. (See Illustration 21.) 12. Plumb and square the tower. Mark a point through each slot of the wa...

19 FIXED GLASS FRAME ATTACHMENT 13. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. ILLUSTRATION 23 SEALANT FIXEDGLASS ENDEXTRUSION

20 14. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws. Seal the end cap and place into the end of the lower track. Secure with self taping screw. (See Illustration24.) CAULK BACKWALL WALL END CAP F-EXTRUSION CAULK WALL L-EXTRUSI...

2I. Attach the shower hose. (See Illustration 27.)Use the washer supplied with the showerhose. 22. For hot and cold operation of the handle, see Illustration 28. HOT COLD HANDLE OPERATION ILLUSTRATION 28 OFF HAND HELDSHOWER WASHER TOWER WALL FLEX HOSE WASHER TEFLONTAPE WATERCONNECTOR WALL BAR ILLUST...

Printed in the U.S.A. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type.It is the responsibility ...