Jacuzzi 300 - Manual
Jacuzzi 300 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION INSTRUCTIONS; fl; HOT; BACK TO BACK OR REVERSE INSTALLATION; Page 2
- Page 4 – TROUBLESHOOTING; nished the installation turn ON valve to make sure; cold water; rst and then; CARE INSTRUCTIONS; a damp cloth and blot dry with a soft towel.; Page 4
- Page 5 – The; MIX TEMPERATURE-VS-POSITION OF ROTATIONAL LIMIT STOP; ed by; Setting of limiter
- Page 6 – Jacuzzi Whirlpool Bath; CAUTION; Since plumbing; This page left blank.
OPTICA
™
300
SHOWER MIXER/TRANSFER VALVE
INSTALLATION INSTRUCTIONS
INSTALLER: LEAVE THIS INSTRUCTION MANUAL FOR OWNER'S/USER'S REFERENCE
WARNING:
This system/device must be set by the installer to ensure safe, maximum temperature. Any change in
the setting may raise the discharge temperature above the limit considered safe and may lead to scalds.
CAUTION:
As the installer of this valve, it is your responsibility to properly
install
and
adjust
this valve per the
instructions given. This valve does not automatically adjust for inlet temperature changes, therefore, it is necessary
to adjust the Rotational Limit Stop at the time of installation.
You must
inform the owner/user of this requirement by
following the instructions below. After installation and adjustment, you must write in the temperature and the date
you adjusted the Rotational Limit Stop on the warning label provided and apply or attach it to the hot water heater.
Be sure this instruction sheet is delivered to the owner/user.
WARNING:
This pressure balanced bath valve is designed to minimize the effects of outlet water temperature
changes due to inlet pressure changes, commonly caused by dishwashers, washing machines, toilets and the like.
It may not provide protection from scalding when there is a failure of other temperature controlling devices elsewhere
in the plumbing system if the Rotational Limit Stop is not properly set, or if the hot water temperature is changed after
the Rotational Limit Stop is set, or if the water inlet temperature changes due to seasonal changes.
OPTICA 300
FINISHING WALL
TILE (FINISH SURFACE)
FACEPLATE (SEALANT NOT PROVIDED)
TRIM SLEEVE OF TRANSFER VALVE
GASKET
TRIM SLEEVE
2-3/8" DIA.
2-3/8" DIA.
WOOD CROSS MEMBER
REAR VIEW
(FRONT HAS RED
AND BLUE DOTS)
GASKET
COPPER PIPE (NOT PROVIDED)
REAR VIEW
SEALANT (SILICONE) ON BACKSIDE OF
FACEPLATE
FEMALE THREAD TO SWEAT ADAPTOR
(NOT PROVIDED)
LEFT-HAND THREAD TO
SWEAT ADAPTOR (NOT PROVIDED)
4-15/16" MINIMUM
SEALANT (100% SILICONE) ON BACKSIDE OF
FACEPLATE (SEALANT NOT PROVIDED)
NOTE: WHEN INSTALLING BAND, RING, ROPE
OR FACETED HANDLE, PULL TRIM SLEEVE OUT
TO MEET HANDLE.
PLASTER GUARD
©1995 Jacuzzi Whirlpool Bath G570000 D 12/06
Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION INSTRUCTIONS WARNING: Failure to follow these instructions could prevent the mixer/transfer valve from functioning properly.1. Shut OFF water supplies. 2. Install the body (1) so the surface of the fi nished wall is fl ush with the front of the plasterguard (2). The plasterguard is moun...
Faucet leaks from bath spout/showerhead – SHUT OFF WATER SUPPLIES Replace seats and springs – Repair Kit RP4993. Check conditions of lower o-rings and replace if necessary. Replace housing assembly (PN D513000) – Re-pair Kit RP19805 CONDITION REMEDY Unable to maintain constant water temperature Repl...
1st Position 2nd Position 50 70 50 70 70 70 40 85 3rd Position 61 79 67 83 74 89 70 101 4th Position 68 83 75 90 84 97 84 110 5th Position 74 87 85 96 91 104 95 117 6th Position 79 90 91 101 99 110 103 125 7th Position 82 93 97 104 104 115 109 130 8th Position 85 95 104 107 108 118 115 135 (Factory ...
