Jacuzzi Faucet Kit - Manual
Jacuzzi Faucet Kit – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Mounting the Fill Spout; Align the fi ll spout holes with the holes just drilled; Do not over tighten; Remove excess sealant using damp cloth.; Mounting the Valves; MOUNTING THE VALVES
- Page 4 – Do not use oil; Installing the Faucet Handles
- Page 5 – Installation for Top Access; Do not use sharp tools!; Faucet Valve Replacement
- Page 6 – Jacuzzi Whirlpool Bath; CAUTION
- Page 7 – HOLE DRILLING TEMPLATE—WATER RAINBOWTM
The Water Rainbow fi ll spout/faucet kit is designed
for installation on most Jacuzzi Whirlpool Bath
products or on any bath having suffi cient rim space
for mounting. The installation procedure requires
drilling holes in the bath shell, mounting fi ttings,
and making the proper water supply connections
to the faucet valves and fi ll spout. Hole drilling
templates and instructions are provided here for
this purpose.
Contents of Kit:
Water Rainbow fi ll spout as-
sembly, faucet handles with inserts--hot (red dot)
and cold (blue dot), faucet valve assembly (2),
1/4-20 x 1-1/2" hex bolt with/washer and locknut
(2), 1-1/2" diameter. push-on speednut (2), faucet
handle gasket (2), #10-24 x 3/8" PHPM screw (2),
cartridge valve wrench with instructions.
Preparation
Locate the area on the bath or spa rim where
the Water Rainbow and faucet valves are to be
installed. For separated valve installations, refer to
illustrations B and G; for paired valve installations,
refer to illustrations C and H.
For installation on all baths, locate the Water Rain-
bow fi ll spout and valves on a level surface which
will allow water to clear the rim and fl ow directly into
the bath (see illustration A). Also be certain the fi ll
spout has easy access and that there is adequate
space for plumbing connections to the fi ll spout,
both before and after installation. (Refer to plumb-
ing instructions regarding top access installation,
illustration M.)
Dry fi t the Water Rainbow fi ll spout and valves in
the desired area (before drilling holes) to be sure
the location is appropriate.
Drilling Holes
Detach the templates (on back page) and tape
them onto the acrylic surface of the bath rim, lo-
cating the center lines of the fi ll spout and valve
holes according to appropriate dimensions given
in Illustration B or C.
Note: To insure template has been printed to
scale, measure the 2 1/2" spacing from center
Fill Spout mark and 9/32" hole mark for the 1/4
- 20 Hex Bolt anchors.
IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.
Water Rainbow™ Fill Spout/Faucet Kit
Installation Instructions
LOCATE FILL SPOUT
ON TOP OF BATH
RIM TO ALLOW
DIRECT WATER
FLOW INTO BATH
INSIDE OF
BATH
RIM
1/4" MIN.
A
INTERIOR OF
BATH OR SPA
1-1/2" DIA.
1/2"
15/64" DIA.
1-3/8" DIA.
15/64" DIA.
2-1/2"
2-1/2"
1/2"
9/32" DIA.
15-64"
HOLE DRILLING SCHEME FOR WATER RAINBOW
SPOUT AND FAUCETS - PAIRED VALVE CONFIGURATION
C
1-1/2" DIA.
15/64"
3"
11/16"
COLD
HOT
FAUCET
HOLES
9/32" DIA.
7"
HOLE FOR
FILL SPOUT
INTERIOR OF
BATH OR SPA
1-1/2" DIA.
1/2"
15/64" DIA.
15/64" DIA.
1-3/8" DIA.
15/64" DIA.
7"
2-1/2"
2-1/2"
7"
11/16"
15/64" DIA.
15/64" DIA.
15/64" DIA.
1-1/2" DIA.
HOT WATER
FAUCET HOLE
9/32" DIA.
9/32" DIA.
15/64" DIA.
COLD WATER
FAUCET HOLE
HOLE FOR FILL SPOUT
HOLE DRILLING SCHEME FOR WATER RAINBOW
SPOUT AND FAUCETS - SEPERATE VALVE CONFIGURATION
B
1/2"
WATER RAINBOW FILL SPOUT
AND FAUCET HANDLES
Jacuzzi Whirlpool Bath 6683000G 8/06
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Using a scribe tool or awl, mark the center points for all holes, then remove the template. Drill holes from the fi nished surface side of the unit carefully, being sure they are the proper size. We recommend that you drill pilot holes and then use the recommended drill size. For best results, begin...
Operation Check for proper operation of the fi ll spout. Always fi ll the bath with a mixture of hot and cold water. Wa-ter temperatures in excess of 140° F may damage the fi ll spout and/or discolor the bath's surface. Plumbing Connections Note: Turn off water at main shut-off valve before making p...
Installation for Top Access If service access to Water Rainbow plumbing under the rim is not possible, it is possible to install the spout so that it can be replaced at a later date (if necessary) from the top of the rim. To do this, allow at least 2" of fl exibility in the piping so it can be p...
