INSTEON 2475S2 - Manuals - manualsarea.com

Page 3 - In-LineLinc Relay – Features and Benefits; Features

Page 3 of 14 2475S2 - Rev: 1/21/2014 7:57 AM In-LineLinc Relay – Features and Benefits Congratulations on purchasing the high-quality INSTEON In-LineLinc Relay Switch with Sense. W ith its easy-install module, you can not only add conveniently hidden remote control to the lights wired to In-LineLinc...

Page 4 - Quick Start Guide; Preparing to Install In-LineLinc; Tools Needed; Non-conductive probe; Installing In-LineLinc

Page 4 of 14 Rev: 1/21/2014 7:57 AM What’s in the Box? - In-LineLinc Relay - Quick Start Guide - Six (6) wire nuts Preparing to Install In-LineLinc CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for instal...

Page 5 - Enable power to the switch from the circuit breaker or fuse panel.

Page 5 of 14 Rev: 1/21/2014 7:57 AM 6) Referring to the diagrams below, use the included wire nuts to connect the fixture’s Line, Load, Neutral, Ground and Sense wires (if using) to In-LineLinc’s corresponding wires. 7) Enable power to the switch from the circuit breaker or fuse panel. 8) Use In-Lin...

Page 6 - Using In-LineLinc Relay; Using the ON and OFF Buttons; Tap ON button to turn load full-on; An Important Note About INSTEON Networks; dual-band INSTEON products; Using In-LineLinc Relay’s Sense Wire; Disabling the Sense Wire; Re-enabling the Sense Wire; In-LineLinc’s status LED will start blinking.

Page 6 of 14 Rev: 1/21/2014 7:57 AM Using In-LineLinc Relay Using the ON and OFF Buttons The small button switches allows you to test the load and adjust its settings prior to final installation. - Tap ON button to turn load full-on - Tap OFF button to turn load full-off An Important Note About INST...

Page 7 - Temporarily Disabling the Sense Wire; Linking In-LineLinc Relay as an INSTEON Responder; The load wired to In-LineLinc will respond appropriately.; Unlinking In-LineLinc Relay as an INSTEON Responder; twice

Page 7 of 14 Rev: 1/21/2014 7:57 AM Temporarily Disabling the Sense Wire The Sense wire may be temporarily disabled so that In-LineLinc will not automatically send INSTEON commands or control its load, regardless of change in sensor state. For example, if you are working or entertaining outside and ...

Page 8 - Linking In-LineLinc Relay as an INSTEON Controller; Linking In-LineLinc Relay to Multiple Responders; Unlinking In-LineLinc Relay as an INSTEON Controller; ) Press and hold In-LineLinc’s Set button until it beeps again.; Advanced Features; Creating INSTEON Scenes

Page 8 of 14 Rev: 1/21/2014 7:57 AM Linking In-LineLinc Relay as an INSTEON Controller With the Sense wire connected, you can control INSTEON responders based on the state of In-LineLinc’s load—it will automatically activate the connected load and any other linked devices when it detects 120V (such ...

Page 9 - Unlinking Multiple Responders from In-LineLinc Relay; Power Restore

Page 9 of 14 Rev: 1/21/2014 7:57 AM In-LineLinc’s status LED will start blinking. 3) Tap In-LineLinc’s Set button until it beeps again. You will have 4 minutes to complete the next step before multi-linking mode times out. 4) One at a time, press and hold each responder’s Set button about 3 seconds....

Page 10 - Setting the X10 Address; Additional Resources

Page 10 of 14 Rev: 1/21/2014 7:57 AM X10 Settings Setting the X10 Address Most INSTEON devices are X10 ready, meaning that they can respond to X10 commands from any X10 controller. And it can send X10 commands to X10 devices. However, to operate an INSTEON device in X10 mode, you must first set up a...

Page 12 - Troubleshooting; Problem

Page 12 of 14 Rev: 1/21/2014 7:57 AM Maximum Amps 15 amps Standby power consumption 0.68 watts Certifications Safety tested for use in USA and Canada (UL-507, CSA C22.22 #14-05) X10 Features X10 Primary Addresses 1 X10 Scene Addresses 1 X10 Status Response Supported X10 Resume Dim Supported by setti...

Page 13 - Responder

Page 13 of 14 Rev: 1/21/2014 7:57 AM INSTEON controller. unlinking In-LineLinc from it. Responder . The light turned on by itself. Another controller, a timer or stray X10 signals triggered In-LineLinc. Install a powerline signal blocker in your home to keep X10 signals from neighboring homes from i...

Page 14 - Certification and Warranty

Page 14 of 14 Rev: 1/21/2014 7:57 AM Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the ...