INSTEON 2453-222(US) - Manuals

Page 3 - Tools Needed

Page 3 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM About DIN Rail On/Off Installation Preparation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for installation in accordance with the local ...

Page 4 - Identify Switch Type; Installation

Page 4 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Identify Switch Type Before you install DIN Rail behind a switch, you must determine which type of switch you have—latching (the default setting), single momentary or dual momentary—as each is wired differently. If you are using DIN Ra...

Page 5 - Switch Operation Mode; Change Mode

Page 5 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Switch Operation Mode By default, DIN Rail is programmed for a latching switch. If you are installing DIN Rail behind a single momentary or dual momentary switch, you must change DIN Rail’s local-control switch operation to single mome...

Page 6 - Local Control Operations; Single Momentary Wall Switch; Adjust Local Settings; Change LED Brightness

Page 6 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Local Control Operations DIN Rail’s switch operation mode affects how it responds to commands; so it’s important to properly program DIN Rail for the correct type of switch you are installing. DIN Rail on/off buttons function exactly l...

Page 7 - Error Blink; INSTEON Setup; INSTEON Controllers, Responders and Links; controller; Make DIN Rail a Responder

Page 7 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM LED will start blinking green 4) Tap set button once LED will start double-blinking green 5) Press and hold set button until it beeps LED will turn green (at brightness of connected load) 6) Press and hold DIN Rail on/off buttons to br...

Page 10 - Assign an X10 Address; Specifications

Page 10 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM 5) Slowly tap set DIN Rail button 3 times LED will start double-blinking green 6) Press and hold DIN Rail set button (and don’t let go) DIN Rail will begin a long beep 7) Release DIN Rail set button after beeping has stopped After a f...

Page 12 - Troubleshooting; Problem

Page 12 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Weight 6.17 oz (175g) Operating environment Indoors Operating temperature range 32° to 104° F (0° to 40° C) Operating humidity range 0-90% relative humidity Storage temperature range -4° o to 158° F (-20° to 70° C) Electrical Voltage ...

Page 14 - Phase Bridge Detect Beacon/RF Range Test

Page 14 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Phase Bridge Detect Beacon/RF Range Test On/Off module automatically bridges the electrical phases in your home (via communications with other dual-band devices on the “other phase”). This is only important in 2-phase homes with power...

Page 15 - Certification and Warranty

Page 15 of 16 2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has be...