Epson U325D - TM B/W Dot-matrix Printer- Manuals

Page 2 - Page ii; Change Log

Programmer’s Guide POSjet ® 1500 General Information Page ii Rev N Nov-10 Change Log Rev A Never Released Rev B Nov 2001 Initial Release Rev C Jan 2002 1) Corrected the Auto Journal Documentation 2) Corrected the [ESC]f Quick Reference listing. 3) Fixed the OCR listing. (The wrong font was used to p...

Page 3 - Rev N; POSjet; Disclaimer; Regulatory Compliance

Programmer’s Guide POSjet ® 1500 General Information Nov-10 Rev N Page iii POSjet ® 1500 Disclaimer © 2010 TransAct Technologies, Inc. All rights reserved. NOTICE TO ALL PERSONS RECEIVING THIS DOCUMENT: The information in this document is subject to change without notice. No part of this document ma...

Page 4 - TransAct Technical Support; Please have the following information at hand:

Programmer’s Guide POSjet ® 1500 General Information Page iv Rev N Nov-10 Canadian Department of Communications Radio Interference Statement The POSjet ® 1500 Printer does not exceed Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the ...

Page 5 - Where Can You Find More Information?; Technical Support; Contacting TransAct’s Ithaca Facility

Programmer’s Guide POSjet ® 1500 General Information Nov-10 Rev N Page v Where Can You Find More Information? Our Internet Support and Sales Services www.transact-tech.com TransAct Technologies Inc. maintains an Internet web site with content devoted to product support. Within the Support Services s...

Page 6 - Page vi; Table of Contents; POSJET

Programmer’s Guide POSjet ® 1500 General Information Page vi Rev N Nov-10 Table of Contents POSJET ® 1500 III Disclaimer iii Copyright iii Regulatory Compliance iii North America: iii Europe: iii Federal Communications Commission Radio Frequency Interference Statement iii Canadian Department of Comm...

Page 7 - SETUP AND INSTALLATION PROCEDURES

Programmer’s Guide POSjet ® 1500 Table of Contents Nov-10 Rev N Page vii External Powered DC 17 Cash Drawer 17 SETUP AND INSTALLATION PROCEDURES 17 Overview of Printer Controls 18 Leaving the 1500 Connected to a Power Source 18 Operating the Keypad Controls 18 Button Function Descriptions: 19 * Butt...

Page 8 - Page viii; COLOR PRINTING AND PRINT DRIVERS

Programmer’s Guide POSjet ® 1500 General Information Page viii Rev N Nov-10 Level 0 Diagnostics 45 Firmware Test 45 Boot Loader Mode 45 Extended Diagnostics 46 Self-Test Diagnostics 46 Hex-dump Mode 46 Configuration Mode 47 Configuration Mode 47 Remote Configuration Software 47 Manual Configuration ...

Page 9 - PROGRAMMING CONTROLS

Programmer’s Guide POSjet ® 1500 Table of Contents Nov-10 Rev N Page ix Operational Troubleshooting 86 Understanding Fault Indicators 86 Indicator Light Blink Patterns 86 Keypad Indicator Troubleshooting Chart: General Problems 87 Keypad Indicator Troubleshooting Chart: Serious Problems 87 Correctin...

Page 10 - Page x

Programmer’s Guide POSjet ® 1500 General Information Page x Rev N Nov-10 Print and Feed Commands 203 Line Spacing Commands 205 Character Commands 205 International Character Sets 207 Panel Button Commands 213 Paper Sensor Commands 214 Print Position Commands 216 Bit-Image Commands 218 Status Command...

Page 11 - Remote Power Control; Table of Tables

Programmer’s Guide POSjet ® 1500 Table of Contents Nov-10 Rev N Page xi Print Buffer Flow 261 Printer Buffer Size 263 Serial Mode Plug and Play 263 Using DSR 263 Serial Device Identification 263 Serial Port Inquire 264 Display Pass Through 265 Remote Power Control 265 Remote Printer Reset 266 Reset ...

Page 12 - Page xii

Programmer’s Guide POSjet ® 1500 General Information Page xii Rev N Nov-10 Table 30 Character Pitch 111 Table 31 Inter-character Spacing 112 Table 32 Language Table ID‘s 115 Table 33 Code Page Definition Table 117 Table 34 Euro Character Substitution Matrix 118 Table 35 OCR MA-3 122 Table 36 Max/Min...

Page 13 - Table of Figures

Programmer’s Guide POSjet ® 1500 Table of Contents Nov-10 Rev N Page xiii Table of Figures Figure 1 Printer Dimensions 3 Figure 2 Receipt Printable Area 4 Figure 3 Environmental Conditions:Typical Operating Range 5 Figure 4 Cash Drawer Pin Assignments 9 Figure 5 Draft 12 x 12 Font 12 Figure 6 Large ...

Page 15 - Printer Test and Configuration Programs; PJColor

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 1 POSjet ® 1500 Features/Specifications Standard Features Print Speed: 12 lps. at 10 char. per line Print Resolution: Max. 208 dpi. Horizontal, 96 dpi. Vertical Simple Snap-In, No-Mess Cartridges with Fast-Drying Ink Standard...

Page 16 - Single Color

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 2 Rev N Nov-10 Drivers and Utilities Available POSjet ® 1500 Drivers and Utilities can be downloaded from our web site, or call our Technical Support Department to request a Software Developer‘s Toolkit (CD-ROM). POSjet Image Converter Ut...

Page 17 - Physical Printer Specifications; USB

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 3 Physical Printer Specifications F i g u r e 1 P r i n t e r D i m e n s i ons Width Depth Height Without Knife 6.75" 9.75" 5.92" (172 mm) (248 mm) (151 mm) With Knife 6.75" 9.75" 6.44" (172 mm) (248 ...

Page 18 - Page 4; Cut to line of print; Auto-cutter Position; Sensors; Paper low indicator; Friction feed

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 4 Rev N Nov-10 Auto-cutter (Partial Cut Option) A receipt auto-cutter is an optional feature with all POSjet ® 1500 Printers. Cutter type Guillotine Cut to line of print 1.635" (41.52 mm) Cutter life 1,000,000 cuts Auto-cutter Positio...

Page 19 - ela; Storage; The POSjet; Typical Operating Range:; Printer Life

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 5 R ela tiv e H um idit y Temperature (°C) 10% 60% 40% 30% 20% 50% 90% 80% 70% 5 0 -40 10 15 20 25 30 35 40 60 70 -10 45 5% Storage Shipping Typic al Operating Range E xt e n d e d O p e ra ti n g R a n g e Environmental Cond...

Page 20 - Page 6; Power and Communication Specifications; Power Requirements; DC Powered Versions; Parallel Interface; Parallel Pin Assignments; Signal

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 6 Rev N Nov-10 Earth Ground +24 Vo lt Supply Ground (+24 V dc) Power and Communication Specifications Power Requirements DC Powered Versions Supply voltage: 24 Vdc 10% Supply Current: 1.0Amps AC Powered Versions Supply Voltage: 100-240 Va...

Page 21 - Parallel Signal Voltage and Current levels; Signal Levels; RS-232 Serial Interface; Serial Port Features; Baud Rates; Serial Pin Assignments

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 7 Parallel Signal Voltage and Current levels Signal Levels Voltage levels 0 V and +5 V (nominal) Logic levels Logic one Driver +2.4 V to +5 V Receiver +2.0 V to +5 V Logic zero Driver 0 V to +0.4 V Receiver 0 V to +0.8 V Curr...

Page 22 - Page 8; RS-232 Serial Interface Signal Voltage and Current levels; Max; Display Pass Through; USB Interface; The Standard USB Type B connector has the following pin functions:

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 8 Rev N Nov-10 RS-232 Serial Interface Signal Voltage and Current levels Voltage Levels Max +-15 Volts Min +- 3 Volts Mark = Off = -3 to –15 Volts Space = On = +3 to +15 Volts Because both the host and printer are DTE's (Data Terminal Equ...

Page 23 - Cash Drawer Interface Description and Specifics; Voltage; Epson

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 9 Cash Drawer Interface Description and Specifics The POSjet ® 1500 Printer supports dual cash drawers with status. The driver in the printer is capable of supplying 24 Vdc at up to 1.5 amps for 250 milliseconds. The POSjet ®...

Page 24 - Printing Specifications; Thermal ink jet; Cartridge arrangement:; Independent; Number of Validation lines:; Refer to ―Validation Form Requirements‖ on pg. 16.; Font

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 10 Rev N Nov-10 Printing Specifications Printing method: Thermal ink jet Cartridge arrangement: 12 nozzle Print dot pitch: 0.0096" (0.244 mm) Printing directions: Bi-directional, logic seeking Paper feed pitch: Default - 0.125" (1...

Page 25 - Character Pitch

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 11 Character Pitch Each character has at least one, half-column, inter-character spacing included within the cell size. The inter-character spacing provides the maximum character pitch as shown in the table below. Change the ...

Page 26 - Standard Print; Character Cell; Horizontal; Draft Font; Large Draft Font

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 12 Rev N Nov-10 Standard Print The three resident fonts in the printer are Draft, Large Draft, and Near Letter Quality (NLQ). The cell size for each is different. In addition, the Small and Large Draft fonts can be printed in Double, Sing...

Page 27 - Rotated Print

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 13 Near Letter Quality (NLQ) Font The near letter quality font is defined in the 24 x 16 cell that is printed in 2 passes. Horizontally, 15 dots are typically used, providing at least 1 half-column between any two characters....

Page 28 - Graphics Generation; The POSjet

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 14 Rev N Nov-10 Graphics Generation The POSjet ® 1500 supports both APA graphics and color raster graphics (Horizontal graphics). In APA graphics mode the following print resolutions are supported. Mode Horizontal Vertical Data APA graphi...

Page 29 - Media Specifications; Hewlett-Packard Inkjet Cartridges; Print cartridge specification:; 2 vertical nozzles; Ink Cartridge Operating Conditions (maximum ratings); Parameter; Paper roll diameter:; feet; Paper and Core Diameter

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 15 Refer to Paper Roll Diameter. Inside Core Dia..45" to .50"(11.4mm to 12.7mm) Outside Core Dia. .82" to .85" (20.8mm to 21.6mm) Media Specifications Media Specifications Hewlett-Packard Inkjet Cartridges Pri...

Page 30 - Validation Form Requirements

Features/Specifications POSjet ® 1500 Programmer’s Guide Page 16 Rev N Nov-10 Validation Form Requirements Form thickness-single part: .003" to .0047" (.076 mm. to .119 mm.) Form Size (Min): 2.75" high x 2.75" long (69.8 mm. x 69.8 mm.) Form Size (Max): 8.5" high x 11" long (...

Page 31 - Electrical Specifications; Interface Description; Driver voltage; Setup and Installation Procedures

Programmer’s Guide POSjet ® 1500 Features/Specifications Nov-10 Rev N Page 17 Electrical Specifications External Powered AC The POSjet ® 1500 Printer is designed to be AC self-powered in domestic and international markets. The printer is equipped with a detachable universal input power supply that i...

Page 32 - Overview of Printer Controls; Leaving the 1500 Connected to a Power Source; Do not unplug the printer from it’s power source.; Operating the Keypad Controls

Control Codes POSjet ® 1500 Programmer's Guide Page 18 Rev N Nov-10 Overview of Printer Controls Leaving the 1500 Connected to a Power Source The POSjet ® 1500 Printer uses Hewlett-Packard inkjet print cartridges. Unlike consumer inkjet print cartridges, the HP print cartridge does not need to be ca...

Page 33 - Cartridge Status Monitoring

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 19 Button Function Descriptions: The primary functions of each of the buttons are described below. These buttons may also have alternate functions when the printer is in self-test and configuration modes. * Button The * Button is ...

Page 34 - Open Cover Button; OPEN; Indicator Light Descriptions; Form Indicator

Control Codes POSjet ® 1500 Programmer's Guide Page 20 Rev N Nov-10 a form to be placed in the validation slot. If a form is already present in the printer, pressing the FORM Button will move the form in a downward direction. Open Cover Button The OPEN COVER Button is used to access the rear paper r...

Page 35 - Unpack the Printer

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 21 Unpack the Printer Be sure to save the box and packing materials in case you need to send the printer in for service. TransAct Technologies is not responsible for damaged return items that are not packaged in original shipping ...

Page 36 - Connect Power and Communications; Installation Overview; Three cables are required to be connected to the printer; Power

Control Codes POSjet ® 1500 Programmer's Guide Page 22 Rev N Nov-10 Connect Power and Communications Installation Overview F i g u r e 1 2 P o we r a n d C o m m u n i c a t i on s C o n n e c ti o n s Three cables are required to be connected to the printer Power Communications Cash Drawer

Page 37 - Using the Cable Restraints

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 23 Using the Cable Restraints Cable restraints are developed to protect against accidental unplugging of the printer while it is in use. Be sure to properly route the communications cable using the restraints provided on the back ...

Page 38 - Connecting the Communication Cable; These interfaces include:; Connecting Serial Cables

Control Codes POSjet ® 1500 Programmer's Guide Page 24 Rev N Nov-10 Connecting the Communication Cable The POSjet ® 1500 may be equipped with a number of different communications interface cards. These interfaces include: RS-232 Serial with 9-pin connector RS-232 Serial with 25-pin connector IEEE128...

Page 39 - Connecting Parallel Cables; Connecting USB Cables

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 25 Connecting Parallel Cables 1. Disconnect all power from the printer and host system or personal computer. 2. Connect the 25/36-pin Parallel Interface Cable to the connector located on the back of the printer. Tighten the two mo...

Page 40 - Connecting the Cash Drawer; Connecting Cash Drawer Cable to the Printer

Control Codes POSjet ® 1500 Programmer's Guide Page 26 Rev N Nov-10 Connecting the Cash Drawer The POSjet ® 1500 printer can be configured to operate with cash drawers designed to work with printers from different manufacturers. This configuration is preset at the factory and is identified by means ...

Page 41 - Connecting the Power Cord (with power supply); Set the printer into OPERATIONAL/ON mode by pressing the

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 27 The POSjet ® 1500 Printer may be powered from an external 24 Vdc power source, or may be equipped with a factory installed PowerPocket ® power supply. Refer to the specification section for DC power connector specifications. Co...

Page 42 - Connecting the DC Power Cord (no power supply); Orientate the printer upside-down and find the DC power socket.

Control Codes POSjet ® 1500 Programmer's Guide Page 28 Rev N Nov-10 Connecting the DC Power Cord (no power supply) 1. Orientate the printer upside-down and find the DC power socket. 2. Locate the DC power cord and connect it to the Interface Card‘s power socket, then route the cord through the cable...

Page 43 - Upper Limit Setting:; Paper Low Setup; Adjusting the Paper-Low Sensor

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 29 Factory Setting: The factory setting leaves room for adjusting the Paper Low Sensor up or down by three full turns with a screw driver. Upper Limit Setting: When adjusted, the sensor will move up and away from the Cabinetry Bas...

Page 44 - Paper Low Adjustment Requirements; Paper Low Adjustment Settings

Control Codes POSjet ® 1500 Programmer's Guide Page 30 Rev N Nov-10 Paper Low Adjustment Requirements Use the following table to decide how much paper you want to remain after paper low sensing has occurred. TransAct‘s expected results are based on paper and paper roll with these specifications. Ref...

Page 45 - Loading Ink Cartridges and Paper; Installing Ink Cartridges; Use the

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 31 Loading Ink Cartridges and Paper Note 1: FIRST TIME INSTALLATION: An ink cartridge(s) can be found in the pouch that shipped with your printer. NOTE 2: When installing new ink cartridges and a new paper roll for the first time,...

Page 47 - Installing a New Paper Roll Using Insta-Load

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 33 Figure 20 Installing the New Paper Roll Installing a New Paper Roll Using Insta-Load ® Before you attempt to load the paper roll, make sure that the printer is plugged in and that the printer is set to the OPERATIONAL/ON mode. ...

Page 48 - Printing the Configuration Summary Receipt; Exiting Self-Test Mode; Parallel Printer

Control Codes POSjet ® 1500 Programmer's Guide Page 34 Rev N Nov-10 Printing the Configuration Summary Receipt This printer has been shipped with a pre-printed, Configuration Summary Receipt that shows how the printer has been configured at our factory. This Configuration Summary Receipt can be foun...

Page 49 - Verifying the Printer Setup; Verify the communications interface card

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 35 Verifying the Printer Setup Before you install a POSjet ® 1500 Printer into your system, you should verify that the printer is configured as required by your system. There are four parts to this verification process. 1. Verify ...

Page 50 - Installing the new interface card; Install the retaining screw.; Verify the Cash Drawer Interface

Control Codes POSjet ® 1500 Programmer's Guide Page 36 Rev N Nov-10 Installing the new interface card Configure the cash drawer jumpers. See "Verify the Cash Drawer Interface‖ on page 36. 1. Slide the interface card into the printer. Make sure the interface card sits flush with the retaining scr...

Page 52 - Using Ink Cartridges; Carriage Configuration; Care of Ink Cartridges; Never

Control Codes POSjet ® 1500 Programmer's Guide Page 38 Rev N Nov-10 POSjet ® 1500 Operation Using Ink Cartridges The POSjet ® 1500 is available in single or dual cartridge configurations. Several physical differences exist between the single and dual cartridge printers. The most obvious is the abili...

Page 53 - Determining Ink Cartridge Status; NEW; Keypad Status

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 39 Determining Ink Cartridge Status The POSjet ® 1500 has been designed to monitor ink consumption rates and report ink levels to the user via a printable ink status. To print out an ink status receipt press the NEW CARTRIDGE butt...

Page 54 - Validation Form Insertion and Orientation; Validation Orientation; Form Requirements; Landscape Mode; Form Orientation

Control Codes POSjet ® 1500 Programmer's Guide Page 40 Rev N Nov-10 Validation Form Insertion and Orientation Validation Orientation The POSjet ® 1500 accepts validation forms in both portrait and landscape orientations. Each of the two different orientations have specific print zones, and print cha...

Page 55 - Inserting Validation Forms; FORM; Printable Side of Form

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 41 Inserting Validation Forms The POSjet ® 1500 is designed to run validation either by using application software, or manually. Forms can be inserted in either landscape or portrait orientation. Regardless of the orientation, the...

Page 56 - Preventing and Clearing Validation Jams; Removing a Validation Jam; simply pressing and holding the; Removing a Validation Jam Manually; Open the printer‘s front cover.

Control Codes POSjet ® 1500 Programmer's Guide Page 42 Rev N Nov-10 Preventing and Clearing Validation Jams Inserted forms should not be touched during the printing, or ejection process. Pressing or pulling the paper during ejection may cause the validation process to jam. If a jam condition occurs,...

Page 57 - Printer Self Testing and Diagnostics; Printer Self-Testing; is activated, call; TEST-Print Configuration

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 43 Printer Self Testing and Diagnostics Printer Self-Testing The POSjet ® 1500 has been designed to perform several self-tests and will also allow a technician to access the printer‘s configuration settings. It is important to ins...

Page 59 - Level 0 Diagnostics; Level 0 diagnostics perform the following tasks:; Firmware Test

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 45 Level 0 Diagnostics Level 0 diagnostics always and only run at power up. Level 0 diagnostics perform the following tasks: 1. Basic System Integrity 2. Vector Integrity 3. RAM Test 4. Flash Boot Loader Integrity 5. Flash Firmwar...

Page 60 - Extended Diagnostics; OFF; Self-Test Diagnostics

Control Codes POSjet ® 1500 Programmer's Guide Page 46 Rev N Nov-10 Extended Diagnostics Extended diagnostics are entered after Level 0 diagnostics, are part of the firmware, and are activated in one of two ways. The first is by holding NEW CARTRIDGE button E and/or FEED button and applying power (P...

Page 61 - Configuration Mode; There are two ways to configure the POSjet; 500 be made by a certified; Remote Configuration Software; 500 printer has many configurable features. Most; Manual Emulation Set; To activate the manual emulation set, press and hold the; and; Buttons during power up.

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 47 Configuration Mode There are two ways to configure the POSjet ® 1500 printer. The first is to use the manual configuration sequence by using the keypad controls, and the second is to use TransAct‘s remote configuration software...

Page 62 - Using Self-Test to View Configuration Settings

Control Codes POSjet ® 1500 Programmer's Guide Page 48 Rev N Nov-10 Using Self-Test to View Configuration Settings From configuration mode, a configuration summary receipt will be printed and will show the printer‘s current features and settings. This receipt is the same as the configuration summary...

Page 63 - Making Changes in Configuration Mode; Using the NEW CARTRIDGE Button in Configuration Mode; Baud Rate; What do you want to do?

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 49 Making Changes in Configuration Mode Press the NEW CARTRIDGE Button quickly to scroll through the list of configurable features. Press and hold the NEW CARTRIDGE Button to change the optional settings for each configurable feat...

Page 64 - Configurable Features

Control Codes POSjet ® 1500 Programmer's Guide Page 50 Rev N Nov-10 Configurable Features The following table lists all the configurable features. Not all are available in all configurations. Not all features are available in all emulations. Refer to the Notes column for availability of each feature...

Page 66 - Print Zone

Control Codes POSjet ® 1500 Programmer's Guide Page 52 Rev N Nov-10 Ink Low When At: Signal ink low when x% of the ink has been used. This sets the point when the printer reports ink low. The printer does not stop printing at ink low Ink Low is OFF (never signal ink low) Ink Low when at 75% Ink Low ...

Page 67 - Code Sets

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 53 Code Sets Code Pages The POSjet ® 1500 Printer supports the following code sets. The setting defines only the default printer mode. IBM specifies code pages differently than Epson. Any set can be selected as a default regardles...

Page 68 - Polska Mazovia

Control Codes POSjet ® 1500 Programmer's Guide Page 54 Rev N Nov-10 Code Sets Code Pages 1014 22 Polska Mazovia 1015 23 ISO Latin 2 1016 24 Serbo Croatic I 1017 25 Serbo Croatic II 1018 42 ECMA-94 1019 49 Windows East Europe 1020 50 Windows Greek 1021 51 Latin 5 (Windows Turkey) 1022 52 Windows Cyri...

Page 69 - Serial Interface Options

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 55 Parallel Link Options The parallel option features define how the busy and acknowledge signals operate. Ack-while-Busy Ack-in-Busy • Ack-after-Busy Parallel Port INIT Pin The parallel port INIT pin can be deactivated. Active • ...

Page 70 - Validation Control; Electronic Journal

Control Codes POSjet ® 1500 Programmer's Guide Page 56 Rev N Nov-10 CTS Signal If active, a false CTS prevents the printer from sending any data to the host Not Used • Active Multidrop The multi-drop feature is activated at power up when set to an address. This option is available in PcOS, M50 and M...

Page 71 - Options; Specifies that the cutter option is attached.; May be from 0 to 22mm.

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 57 Electronic Journal This allows the partition of the extended flash to be split between the electronic journal and the user store. If the electronic journal is in use, this feature can not be changed. 64K to Electronic Journal T...

Page 72 - Printer Color Configuration; Ink Cartridge Setup; Single Color Setup; Printing Setup

Control Codes POSjet ® 1500 Programmer's Guide Page 58 Rev N Nov-10 Printer Color Configuration Using Ink Cartridges It is not possible to configure the printer to operate with two black cartridges. Do not store a spare cartridge in the second carriage socket position. Always store extra ink cartrid...

Page 73 - Two-color operation setup allows the POSjet; Left Cartridge Menu; Deactivating the Two-Color Setup (back to Single Color setup)

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 59 Two-Color Ready Setup (single cartridge setup) The two-color ready setup allows the POSjet ® to operate as a Single Color printer with the option of reconfiguring the printer for two-color printing. This reconfiguration can be ...

Page 74 - Color Printing and Print Drivers; Character Graphics; might be formed as follows.

Control Codes POSjet ® 1500 Programmer's Guide Page 60 Rev N Nov-10 Color Printing and Print Drivers The POSjet ® 1500 Printer has bit-image graphic capability and a full PC-compatible graphic character set. The bit image format is similar to that used on other personal computer printers. Three mode...

Page 75 - APA Graphics; Creating an APA graphics file; 500 Printer supports all three resolutions. For good

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 61 F i g u r e 2 5 S a m p l e R e ce i p t When printing line graphics, the data path to the printer must be eight bits. Seven-bit serial protocols do not access the extended characters. The extended characters require that the f...

Page 76 - Color Graphics; Color Bits Received

Control Codes POSjet ® 1500 Programmer's Guide Page 62 Rev N Nov-10 Color Graphics The POSjet ® 1500 is a two-color printer. It is not a full color printer. A full color printer forms the various colors of an image by mixing inks of different colors on the paper. The amount of each color determines ...

Page 77 - Procedure for color horizontal graphics:

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 63 Procedure for color horizontal graphics: There are many ways to generate graphics for the POSjet ® 1500 printer. The easiest is to use the PJColor program. (See the next section.) The other way is to use the Ithaca windows driv...

Page 78 - Printer Drivers and Printer Controls; General Driver Information; Windows Printer Driver:; An OPOS Driver is not a printer driver.; An OPOS Driver should be; control; what is sent to the printer. When using Active X Controls it

Control Codes POSjet ® 1500 Programmer's Guide Page 64 Rev N Nov-10 Printer Drivers and Printer Controls General Driver Information The following information provides a brief descriptive overview of each of the printer drivers that the POSjet ® 1500 can be integrated with: Windows Printer Driver: A ...

Page 79 - Installing Windows

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 65 Installing Windows ® Printer Drivers (WIN95, 98, Me) 1. Insert the “Windows 98, 98, Me printer driver” floppy disk into your diskette drive. 2. Click on “Start” menu -> “Settings” -> “Printers” . 3. Double Click on “Add P...

Page 80 - OPOS Drivers Installation Instructions; “driver”; To Install the USB drivers

Control Codes POSjet ® 1500 Programmer's Guide Page 66 Rev N Nov-10 OPOS Drivers Installation Instructions Run SetupOPOS.exe. The communications will default to “COM2” . If the communication port is not setup at installation, the first time the printer service object Open method is called, a Comm po...

Page 81 - Configuring Windows; Additional StartDoc Commands:

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 67 Configuring Windows ® Printer Drivers (WIN95, 98, Me) The standard Windows printer driver configuration properties are described in the operating system‘s help under the ―printers‖ topic. The Ithaca specific configuration is de...

Page 82 - True Type Fonts

Control Codes POSjet ® 1500 Programmer's Guide Page 68 Rev N Nov-10 Font Options Tab (Win 9x/Me only) These options control how font processing is handled in the printer driver. Note: Selecting ―Always map fonts to device resident fonts‖ causes the printer driver to behave in a way that is not how t...

Page 83 - To view, edit, or delete the custom settings

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 69 To view, edit, or delete the custom settings Go to the Windows operating system‘s start RegEdit.exe and go to HKEY_LOCAL_MACHINE\SOFTWARE\PcOSPrinter\Series_1500 for the Series 1500 printers.

Page 84 - Configuring Ithaca OPOS Drivers; This will allow you to remove an OPOS device from the system.; Printing

Control Codes POSjet ® 1500 Programmer's Guide Page 70 Rev N Nov-10 Configuring Ithaca OPOS Drivers To configure the OPOS drivers, either run the ―Ithaca OPOS Setup‖ in the control panel or run the configuration via the ―Start‖ menu, ―Programs‖, ―Ithaca OPOS‖, ―Ithaca OPOS Setup‖. You must choose th...

Page 85 - General Settings; If set, paper low will not be reported until paper is out.; Error Events Asynchronous Mode Only:; Performance; Background Status Updating:; Communications Port:

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 71 General Settings Paper Low = Paper Out: If set, paper low will not be reported until paper is out. Inhibit Events: If set, events will not be generated. Error Events Asynchronous Mode Only: Set to enable firing error events whi...

Page 86 - Cash Drawer Dialog

Control Codes POSjet ® 1500 Programmer's Guide Page 72 Rev N Nov-10 Paper Out: Ignore Paper Out: If this is selected, the print functions will still attempt to print to the printer even when paper out is sensed. This functionality is provided to maximize paper use on the Ithaca Series 90 printer tha...

Page 87 - Printing using a printer driver (Printer Font); 'SELECT OUR PRINTER BY NAME

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 73 Printing using a printer driver (Printer Font) See the documentation that comes with Visual Basic for detailed information on all the function calls that can be made to print via the Windows printer drivers. 'SELECT OUR PRINTER...

Page 91 - Printing via an OPOS driver; There are 3 Modes of printing.; OPOS drivers for detailed information on all the function calls

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 77 Printer.Print "$20.00" Printer.Print "" Printer.Font.Bold = True 'CHANGE COLOR Printer.ForeColor = RGB(255, 0, 0) LinePos = Printer.CurrentY Printer.CurrentX = 1000 Printer.Print "Change Due" Printer.Cur...

Page 95 - Printing via POSPrinter OCX; Dim StrData As String

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 81 Printing via POSPrinter OCX See the documentation that comes with the POSPrinter OCX for detailed information on all the function calls that can be made with the POSPrinter OCX. Dim StrData As String Result = POSPrinter1.SetHan...

Page 96 - Troubleshooting; The five POSjet; Cartridge has been removed; Fault Indicators

Control Codes POSjet ® 1500 Programmer's Guide Page 82 Rev N Nov-10 Troubleshooting Indicator Lights (LED) The five POSjet ® 1500 indicator lights are: Power LED Indicates printer activity and non-recoverable errors Error LED Indicates problems and probability of recovery Paper LED Indicates paper s...

Page 97 - Three types of faults exist; Recovery from Errors; Non-Reportable Error

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 83 The error indicator is the primary fault indicator. It is always on or blinking if a fault has occurred. Three types of faults exist Fully-recoverable faults Paper out or cover open Semi-recoverable faults Head Jam Non-recovera...

Page 98 - Prog

Control Codes POSjet ® 1500 Programmer's Guide Page 84 Rev N Nov-10 Some errors cannot be reported to the host system. These errors are such that the integrity of the printer does not allow continued operation and has no way to report the error. These errors (for the most part) occur during power up...

Page 99 - Startup Troubleshooting; Printer Does Not Turn ON; Printer Will Not Communicate (prints illegible receipts); Remedy; Possible Cause

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 85 Startup Troubleshooting This troubleshooting section provides solutions to problems that may occur with your printer during installation. Printer Does Not Turn ON Possible Cause Remedy Printer is OFF Press and release the * But...

Page 100 - Operational Troubleshooting; Understanding Fault Indicators; Fully-recoverable and Status; Indicator Light Blink Patterns

Control Codes POSjet ® 1500 Programmer's Guide Page 86 Rev N Nov-10 Operational Troubleshooting Understanding Fault Indicators The ERROR INDICATOR LIGHT is the primary fault indicator. It is always On or blinking if a fault has occurred. Three types of faults exist Fully-recoverable faults Paper out...

Page 101 - Keypad Indicator Troubleshooting Chart: General Problems; Keypad Indicator Troubleshooting Chart: Serious Problems; The POSjet will use a combination of the; to signal serious problems. In most

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 87 Keypad Indicator Troubleshooting Chart: General Problems General problems: Use this table to determine problem type Error Type Power LED Error LED Paper LED Left Cartridge Right Cartridge Cover Open ON ON OFF OFF OFF Out of Pap...

Page 102 - Correcting Common Operating Problems; Keypad Lights Are Not Working; Printer Will Not Print (Error Light OFF)

Control Codes POSjet ® 1500 Programmer's Guide Page 88 Rev N Nov-10 Correcting Common Operating Problems This troubleshooting section provides solutions to problems that may occur with your printer. Use the following series of tables to determine printing problems. It is highly recommended that you ...

Page 103 - Printer Will Not Load Or Feed Paper

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 89 Printer Prints With Missing Dots In Characters Possible Cause Remedy Ink Buildup On Ink Cartridges Press the NEW CARTRIDGE Button 2-3 times and try to print again. The NEW CARTRIDGE Button cycles the printer’s ink cartridge cle...

Page 104 - Programming Controls; Control Codes Overview

Control Codes POSjet ® 1500 Programmer's Guide Page 90 Rev N Nov-10 Programming Controls Control Codes Overview This programmer's guide is designed to help users of the POSjet ® 1500 Printer develop applications. POSjet ® 1500 Printers are specialized point-of-sale printers that have several feature...

Page 105 - It is intended that the standard Ithaca; Application Development

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 91 Standard Emulation The standard control codes for the POSjet ® 1500 printer are extensions and subsets of the PcOS IBM emulation provided on other Ithaca ® products. In some cases, an application designed for an Ithaca ® Series...

Page 106 - Ithaca Control Codes and Commands; PcOS Printer Control Codes; The following section defines the Ithaca

Control Codes POSjet ® 1500 Programmer's Guide Page 92 Rev N Nov-10 Ithaca Control Codes and Commands Throughout this Programmer's Guide, charts and tables list commands and features. In most cases, the charts cross -reference the page that describes the command. Commands are grouped by function and...

Page 107 - Quick PcOS Reference Chart By Function; Low Level paper Motion

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 93 Quick PcOS Reference Chart By Function Description ASCII Hex IPCL equivalent code Page Low Level paper Motion Line feed [LF] 0AH &%LF 102 Carriage return [CR] 0DH &%CR 102 Horizontal Motion Back space [BS] 08H &%BS ...

Page 114 - Perform a fine line feed

Control Codes POSjet ® 1500 Programmer's Guide Page 100 Rev N Nov-10 Set print quality mode n=0 Draft (12 x 12) n=1 Large draft (12 x 14) n=2 NLQ (24 x 16) n=3 NLQ (24 x 16) n=4-7 Repeats 0-3 [ESC] I <n> 1BH,49H &%QT {n=0} &%QU {n=1} &%QL {n=2} &%QS {n=3} 113 Perform a fine lin...

Page 116 - Low Level Paper Motion Control

Control Codes POSjet ® 1500 Programmer's Guide Page 102 Rev N Nov-10 Low Level Paper Motion Control Print/Paper Motion Function Carriage return ASCII [CR] Hexadecimal 0DH Decimal <13> IPCL &%CR EPOS 0DH Description The [CR] command prints the contents of the print buffer (if any) and reset...

Page 117 - Horizontal Motion Control

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 103 Horizontal Motion Control Several commands can be used to control the horizontal position of characters. Many applications use space control to position fields. However, the POSjet ® 1500 Printer has the ability to control cha...

Page 119 - Vertical Motion Control

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 105 Vertical Motion Control Function Perform a fine line feed ASCII [ESC] J <n> Hexadecimal 1BH 4AH <n> Decimal <27> <74> <n> IPCL &%FM <m 1 > <m 2 > <m 3 > EPOS [ESC] J <n>...

Page 125 - Resulting

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 111 Function Set character pitch ASCII [ESC] [ P <n> Hexadecimal 1BH 5BH 50H <n> Decimal <27> <91> <80> <n> IPCL &%F1, &%F2, &%F3, &%F4, &%F5, &%F6, &%F7 EPOS [ESC] [...

Page 127 - NLQ fonts cannot be rotated 90 or 270 .

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 113 Character Font Function Begin 12 x 12 draft print mode ASCII [ESC] # <0> Hexadecimal 1BH 23H 00H Decimal <27> <35> <0> IPCL &%QT EPOS [ESC] ! <n> Description The [ESC] # <0> command begi...

Page 129 - Character sets and Code Pages; Language

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 115 Character sets and Code Pages The POSjet ® 1500 Printer supports 65 different international character sets. In IBM and EPOS printers, there are two ways of selecting a character set. One way substitutes international character...

Page 130 - Code

Control Codes POSjet ® 1500 Programmer's Guide Page 116 Rev N Nov-10 ASCII [ESC] [ T <n h > <n l > Hexadecimal 1BH 5BH 54H <n h > <n l > Decimal <27> <91> <84> <n h > <n l > IPCL &%CP <m 1 > <m 2 > <m 3 > <m 4 > EPOS [...

Page 131 - Code Page

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 117 Code Page Country Code/Language Set Decimal <n h > <n l > Hex <n h > <n l > 865 Norway 3,97 3H,061H 866 Cyrillic II-866 3,98 3H,062H 869 Greek 869 3,101 3H,065H 895 Kamenicky (MJK) 3,127 3H,07FH 1008 Gr...

Page 132 - Euro Character Substitution Matrix; Win Cyrillic

Control Codes POSjet ® 1500 Programmer's Guide Page 118 Rev N Nov-10 Function Print control character ASCII [ESC] ^ <n> Hexadecimal 1BH 5EH <n> Decimal <27> <94> <n> IPCL &%CC <m1> <m2> <m3> EPOS [ESC] ^ <n> Description The [ESC] ^ <n> ...

Page 133 - the total number of characters to be replaced

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 119 Function Redefine character set ASCII [ESC] [ S <L L > <L H > <B C > <T 1L ><T 1H > <T 2L ><T 2H > <T 3L ><T 3H > …<T nL ><T nH > Hexadecimal 1BH 5BH 53H … Deci...

Page 136 - OCR Characters; Character

Control Codes POSjet ® 1500 Programmer's Guide Page 122 Rev N Nov-10 OCR Characters Character Name Location Hex, Dec ASCII Equivalent 0 Number 0 30H,48 0 1 Number 1 31H,49 1 2 Number 2 32H,50 2 3 Number 3 33H,51 3 4 Number 4 34H,52 4 5 Number 5 35H,53 5 6 Number 6 36H,54 6 7 Number 7 37H,55 7 8 Numb...

Page 137 - Character Attribute Commands

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 123 Character Attribute Commands Function Select color ASCII [ESC] c <n> Hexadecimal 1BH 63H <n> Decimal <27> <99> <n> IPCL &%CL <m 1 > EPOS none Description The [ESC] c <n> command se...

Page 141 - Print Zone Control

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 127 Print Zone Control Function Set left/right print margins ASCII [ESC] X <n 1 > <n 2 > Hexadecimal 1BH 58H <n 1 > <n 2 > Decimal <27> <88> <n 1 > <n 2 > IPCL none EPOS [ESC] l, [ES...

Page 142 - Print Rotation Commands; Function

Control Codes POSjet ® 1500 Programmer's Guide Page 128 Rev N Nov-10 Print Rotation Commands Rotated print capabilities are available. The print mode commands listed below rotate the print in any of three 90° orientations. In 90° and 270° rotated mode, the print data is first buffered by the printer...

Page 143 - Rotated Print Summary

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 129 Note 3 Use the [ESC] I <n> command to select two-pass rotated font. The font selection must be made before the rotate command. Note 4 Only enhanced and emphasized attributes are available for formatted, rotated print. Th...

Page 144 - Rotated Print Length Format

Control Codes POSjet ® 1500 Programmer's Guide Page 130 Rev N Nov-10 Hexadecimal 1BH 72H 0FH Decimal <27> <114> <15> IPCL &%RX15 EPOS [ESC] T <1> Function End rotated print ASCII [ESC] r <0> Hexadecimal 1BH 72H 00H Decimal <27> <114> <0> IPCL &...

Page 145 - How to use page mode; Page size definition.; Setting the Page Size

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 131 POSjet 1500 Page Mode The POSjet 1500 supports two operational modes, standard and page mode. In standard mode, as a line of text is received it is buffered and printed when the line feed is received. In page mode the printer ...

Page 146 - Width X; Offset O; Page Definition; Embedding Station Selects during Page Definition; if there is room or down if not) to the nearest multiple of 12.

Control Codes POSjet ® 1500 Programmer's Guide Page 132 Rev N Nov-10 Width X 2.5‖ Max 520 dots 2.5‖ Max 520 dots 2.25‖ 468 dots 2.0‖ 416 dots 1.75‖ 364 dots 0.5‖ Min. 96 Dots Offset O 0‖ 0 dots 0‖ 0 dots 0.25‖ 52 dots 0.5‖ 104 dots 0.75‖ 156 dots 2.0‖ 416 dots Height 14 Y 0.5‖ Min. 96 4.125‖ 792 dot...

Page 147 - Auto-cutter and page mode; Parallel port INIT request.; Printing the page

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 133 2) If a validation select command precedes a receipt station select command, the Validation select command will be processed before the page is printed and the receipt station select will be processed after the page is printed...

Page 149 - Command

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 135 Command Active Action Cash drawer commands Yes Immediate action Bell command Yes Immediate action Auto cut commands Delayed The printer will perform a feed to cut and then operate the auto cutter after the page is printed. The...

Page 150 - O + X must be less than 520 and greater than 96.

Control Codes POSjet ® 1500 Programmer's Guide Page 136 Rev N Nov-10 W idth X H e ig h t Y Offset O Receipt or Inserted Form Note 1: O + X must be less than 520 and greater than 96. Note 2: The value of X * Y must be less than or equal to 411,840. Note 3: Y is internally rounded up to the nearest mu...

Page 152 - Check Printing

Control Codes POSjet ® 1500 Programmer's Guide Page 138 Rev N Nov-10 Check Printing A typical personal check is 2.75 by 6 inches. The 2 by 5.1-inch page mode size is ideal for check printing. You can set the Page Position so as to print the ―Date, Pay to the Order Of‖, and the amount fields easily. ...

Page 154 - Standard APA Graphics

Control Codes POSjet ® 1500 Programmer's Guide Page 140 Rev N Nov-10 POSjet ® 1500 Graphics The POSjet ® 1500 Printer conforms to the basic definition of IBM all-points-addressable (APA) graphic commands. It is not designed to print large quantities of graphical data. The printer only prints graphic...

Page 155 - Extended APA Graphics

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 141 Function Print quad-density graphics (240h x 72v dpi) ASCII [ESC] Z <n 1 > <n 2 > Hexadecimal 1BH 5AH <n 1 > <n 2 > Decimal <27> <90> <n 1 > <n 2 > IPCL none Description The [ESC...

Page 158 - Graphics Compression

Control Codes POSjet ® 1500 Programmer's Guide Page 144 Rev N Nov-10 Function Set horizontal graphic mode ASCII [ESC] * <m> <0> <0> Hexadecimal 1BH 2AH <m> <0> <0> Decimal <27> <42> <m> <0> <0> IPCL none Description The [ESC] * <m&...

Page 159 - Defining Macros

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 145 Same-As-Previous Compression In same-as-previous compression, the command does not contain any graphics data. The command specifies that the printer is to use the previous scan line data for the current scan line. ESC h <1&...

Page 164 - User Macros; Programming Considerations; bytes long. All commands

Control Codes POSjet ® 1500 Programmer's Guide Page 150 Rev N Nov-10 EPOS [GS] 3 Description The [ESC] [US] q <Name..> <0> command prints a status report. The file name is ignored and may be omitted. The NUL must be present. The intention of the command is to aid in macro development. No...

Page 165 - Legacy Macro Commands

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 151 for all of the data. As user store space is used, the macro buffer will be larger than the available space in user stor e. Only the used space is saved, but it is possible to define a macro that does not fit in the remaining u...

Page 166 - Bar Codes; Interleaved 2 of 5

Control Codes POSjet ® 1500 Programmer's Guide Page 152 Rev N Nov-10 Bar Codes The POSjet ® 1500 Printer supports the ability to print bar codes. The printer offers a number of formats as defined below. The host does not need to form the graphic image for these bar codes. The host need only send the...

Page 167 - UPC A

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 153 Code 39 Code 39 is an alphanumeric bar code. It is a discrete, self-checking, variable-length code. The printer prints the complete data field. Due to space limitations, only eight characters can be printed. If illegal charact...

Page 168 - Codabar

Control Codes POSjet ® 1500 Programmer's Guide Page 154 Rev N Nov-10 EAN-13 EAN-13 is a fixed-length, numeric, continuous code that employs four element widths. The printer supports EAN -13, which is a superset of UPC that encodes 12 digits. Typically, the format starts with a number set digit, whic...

Page 170 - Manual Validation; Validation Form; Width

Control Codes POSjet ® 1500 Programmer's Guide Page 156 Rev N Nov-10 POSjet ® 1500 Validation Operation The POSjet ® 1500 is configured with a validation feature allowing up to 12 lines of print on a one -ply, inserted form or check. Additionally, a check print function allows the full front or back...

Page 171 - Landscape

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 157 F i g u r e 2 9 V a l i d a t i on P r i n t Z o n e In portrait mode the POSjet 1500 has the ability to print up to 6 inches on a narrow form by loading it into the printer past the current slip stop. Landscape Portrait F i g...

Page 172 - This command requests that a form be inserted in the printer. The; Indicator will blink until

Control Codes POSjet ® 1500 Programmer's Guide Page 158 Rev N Nov-10 Station Select Commands The following commands are used to load and position validation forms. Function Select receipt station ASCII [ESC] f Hexadecimal 1BH 66H Decimal <27><102> IPCL &%SR EPOS [ESC] c 0 <n> D...

Page 173 - Validation operation control

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 159 Function Load to top of form ASCII [ESC]m Hexadecimal 1BH 6DH Decimal <27> <109> IPCL &%VD Description Position a form to the top edge. This command is typically used to print the face of a check in rotated pri...

Page 175 - Set Validation Operation; Bit values

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 161 Function: Set Validation Operation ASCII: [ESC] ~ 0 <n> Hex: 1BH 7EH 30H Decimal: <27><126><48> Description: This command reconfigures the operation of the right form sensor during validation. Where n =...

Page 176 - Configuring the Electronic Journal

Control Codes POSjet ® 1500 Programmer's Guide Page 162 Rev N Nov-10 Electronic Journal The POSjet 1500 has the capability to store electronic journal 17 data in flash memory. There are two ways entries can be made into the electronic journal. The first is by selecting the journal station. The secon...

Page 177 - Initializing the Electronic Journal; The electronic journal can not be deleted without this password.

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 163 Initializing the Electronic Journal Once the electronic journal is partitioned, it can be initialized. Initializing the electronic journal sets the password and formats the flash to accept journal entries. Each entry may be an...

Page 179 - Printing/Reporting and Resetting the Electronic Journal; Entering and using Journal Print Mode

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 165 Function Query the Electronic Journal ASCII [ENQ]<25> Hexadecimal 05H 19H Decimal <05> <25> IPCL None EPOS Description This is a real time status request that returns the current state of the electronic journ...

Page 180 - Journal Print Mode Options; Initialize Journal; Print Last 20 Records; Security; 500 printers leave the factory, the

Control Codes POSjet ® 1500 Programmer's Guide Page 166 Rev N Nov-10 Journal Print Mode Options Initialize Journal If this option is offered, the journal has never been initialized. Selecting this option will initialize the journal with no password. Once initialized, the journal configuration can no...

Page 181 - Electronic Journal Entries; Start journal record

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 167 Electronic Journal Entries There are two ways to place information in the electronic journal. The first is by selecting journal mode. The second is by requesting that validation or receipt information is copied into the electr...

Page 183 - Journal mode; None

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 169 Journal mode Journal mode is a station select command. All data sent to the printer, following the journal mode select command, is stored in the EJ as a single record. Any control commands sent to the electronic journal will e...

Page 184 - Carbon Copy Journal Mode; This command begins a carbon copy journal entry.

Control Codes POSjet ® 1500 Programmer's Guide Page 170 Rev N Nov-10 Carbon Copy Journal Mode Carbon copy mode allows information sent to the receipt or validation station to be copied into the electronic journal. An electronic journal entry is started with a ―Start Carbon Copy‖ mode command and con...

Page 185 - Auto Journal

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 171 Auto Journal The POSjet ® 1500 can simulate an impact printer's ability to duplicate a validation operation on impact receipt paper. The printer will store the validation information and repeat it on the receipt after the vali...

Page 187 - Miscellaneous Commands; General Control

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 173 Miscellaneous Commands General Control Function Disable Paper Out Sensor ASCII [ESC] 8 Hexadecimal 1BH 38H Decimal <27> <56> IPCL &%PF EPOS none Description The [ESC] 8 command temporarily disables the paper ou...

Page 189 - Bit

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 175 Function Configure Audio Alert ASCII [ESC] [BEL] <n 1 > <n 2 > <n 3 > Hexadecimal 1BH 07H <n 1 > <n 2 > <n 3 > Decimal <27> <7> <n 1 > <n 2 > <n 3 > IPCL None E...

Page 192 - Documented Extended Configuration and Control commands

Control Codes POSjet ® 1500 Programmer's Guide Page 178 Rev N Nov-10 Note 4 The printer has a resident OCR-MA font. It is defined and mapped per ANSI X3.111-1986. Once mapped into a code page, it can be removed by issuing an [ESC] y <12> command or a code -page select command. Note 5 In EPOS m...

Page 193 - Printer Status; Status Inquire; Serial and USB Mode Inquire

Programmer's Guide POSjet ® 1500 Codes and Commands Nov-10 Rev N Page 179 Printer Status Status Inquire The POSjet ® 1500 Printer is designed for use as part of an automated system where the host computer makes every attempt to correct problems with the printer. In addition, the host application req...

Page 194 - Dynamic Response Mode; Inquire Commands

Codes and Commands POSjet ® 1500 Programmer's Guide Page 180 Rev N Nov-10 IEEE 1284 Mode Inquire In parallel, IEEE 1284 mode, status information can be returned to the host through the IEEE 1284 reverse channel. After the host makes an inquire request, it activates IEEE 1284 mode 0 reverse channel a...

Page 203 - Ithaca

Programmer's Guide POSjet ® 1500 Codes and Commands Series 50 Compatibility Nov-10 Rev N Page 189 Ithaca ® Series 50 Compatibility Commands 18 To allow the POSjet ® 1500 Printer to replace the Ithaca ® Series 50 Printer without affecting the Series 50 application, the most popular Series 50 emulatio...

Page 207 - Printing part of the journal.

Programmer's Guide POSjet ® 1500 Codes and Commands Electronic Journal Nov-10 Rev N Page 193 If the electronic journal is not password protected, this option will erase the complete journal and reinitialize it. Printing part of the journal. Print Last 20 Records Print First Record. Skip 10 Records. ...

Page 208 - Differences between Epson TM U325D and POSjet; Validation; EPOS Deviations

Epson Control Codes POSjet ® 1500 Programmer's Guide Page 194 Rev N Nov-10 ESC/POS TM Codes (EPOS) The EPOS codes that are supported by the POSjet ® 1500 Printer are listed in this section. TransAct Technologies, Inc. has no control over how Epson extends or changes these control codes. TransAct Tec...

Page 209 - Page Mode; The page mode in the the POSjet; Undocumented Epson Commands; 500 Printer. The TM-U325D printer has a number of commands that

Programmer's Guide POSjet ® 1500 Epson Control Codes Nov-10 Rev N Page 195 Page Mode The page mode in the the POSjet ® 1500 operates Undocumented Epson Commands There are a number of undocumented commands in Epson printers. Where TransAct is aware of these commands, they have been duplicated in the ...

Page 210 - Supported TM-U325D Commands; Print and Feed Commands

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 196 Rev N Nov-10 Supported TM-U325D Commands Print and Feed Commands Command Name Page LF 0AH Print and line feed 203 CR 0DH Print and carriage return 203 ESC d 1BH,64H Print and feed <n> lines 203 ESC e 1BH,65H Print and reverse feed &l...

Page 211 - Paper Sensor Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 197 Supported TM-U325D Commands Paper Sensor Commands Command Name Page ESC c 4 1BH,63H, 34H Select paper sensor(s) to stop printing 214 ESC c 3 1BH,63H, 33H Select paper sensor(s) to output paper out signals 215 ESC c 1 1BH, 63H,...

Page 212 - Undocumented TM-U325D Commands

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 198 Rev N Nov-10 Undocumented TM-U325D Commands Command Name ESC i Auto Cut 230 ESC m Auto Cut 230 ESC u Transmit Peripheral Device Status 222 ESC v Transmit Paper status 222 GS ( A Enter Test Mode 233 Ta b l e 4 1 U n d o c u m e n t e d TM -...

Page 213 - Supported EPOS Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 199 Supported EPOS Commands Print and Feed Commands Command Name Page LF 0AH Print and line feed 203 CR 0DH Print and carriage return 203 ESC d 1BH,64H Print and feed <n> lines 203 ESC e 1BH,65H Print and reverse feed <n&...

Page 215 - Bar Code Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 201 Supported EPOS Commands Bar Code Commands Command Name Page GS h 1DH,68H Set bar code height 229 GS k 1DH,6BH Print bar code 228 GS H 1DH,48H Select printing position of HRI characters 229 GS f 1DH,66H Select font HRI characte...

Page 216 - Extended Electronic Journal Commands; Electronic Journal Commands; Electronic journal initialize and set password

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 202 Rev N Nov-10 Extended Electronic Journal Commands Electronic Journal Commands Command Name Page [ESC][GS]I <Password><0> 1BH 1DH 49H Electronic journal initialize and set password 163 [ESC][GS]E <Password><0> 1BH 1D...

Page 217 - TM-U325D and EPOS Command Descriptions

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 203 TM-U325D and EPOS Command Descriptions The TM-U325D and EPOS emulations are grouped together. The TM-U325D emulation is a subset of the EPOS emulation. The EPOS only commands are noted. Print and Feed Commands Function Print a...

Page 219 - Line Spacing Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 205 Line Spacing Commands Function Select Default Line Spacing ASCII [ESC] 2 Hexadecimal 1BH 32H Decimal <27> <50> Description The [ESC] 2 command sets the line spacing to 1/6 inch, which is equivalent to 12 dots. Func...

Page 221 - International Character Sets; Country

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 207 International Character Sets Country Epson ID Country Epson ID ASCII 0 Greek 437 38 French 1 Greek 928 39 German 2 Greek 437 CYPRUS 41 British 3 ECMA-94 42 Danish I 4 Canada French 43 Swedish I 5 Cyrillic I-855 44 Italian 6 Cy...

Page 224 - Character Code Table

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 210 Rev N Nov-10 Function Print Control Character EPOS ONLY ASCII [ESC] ^ <n> Hexadecimal 1BH 5EH <n> Decimal <27> <94> <n> Range 0 n 255 Description The [ESC] ^ <n> command allows characters from zero to 31...

Page 226 - Turns off all rotation modes

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 212 Rev N Nov-10 Function Turn ON/OFF Double-Strike Mode ASCII [ESC] G <n> Hexadecimal 1BH 47H <n> Decimal <27> <71> <n> Range 0 n 255 Description The [ESC] G <n> command turns on or off double -strike mode....

Page 227 - Panel Button Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 213 Function Set Character Size EPOS ONLY ASCII GS ! <n> Hexadecimal 1DH 21H <n> Decimal <29> <33> <n> Description The GS ! <n> command sets the horizontal and vertical scaling. The upper nibble...

Page 230 - Print Position Commands; the distance from the current position to [(n

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 216 Rev N Nov-10 Print Position Commands Function Set Absolute Print Position EPOS ONLY ASCII [ESC] $ <n l > <n h > Hexadecimal 1BH 24H <n l > <n h > Decimal <27> <36> <n l > <n h > Range 0 n l 2...

Page 232 - Mode; -dot single density

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 218 Rev N Nov-10 Function Set Right Margin EPOS ONLY ASCII [ESC] Q <n> Hexadecimal 1BH 51H <n> Decimal < 29> <81> <n> Range 0 n 255 Description The [ESC] Q <n> command sets the right margin using <n>. ...

Page 233 - Status Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 219 Status Commands Function Transmit Status ASCII [GS] r <n> Hexadecimal 1DH 72H <n> Decimal <29> <114> <n> Range 1 n 2 49 n 50 Description The [GS] r <n> command transmits the status specified...

Page 237 - Printing Paper Command; Select Paper Type for Printing; Range

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 223 Printing Paper Command Function Select Paper Type for Printing TM-U325D with EPOS enhancements ASCII [ESC] c 0 <n> Hexadecimal 1BH 63H 30H <n> Decimal <27> <99> <48> <n> Range n = 1, 1 n 3, ...

Page 238 - Select Paper Type for Command Settings

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 224 Rev N Nov-10 Function Select Paper Type for Command Settings ASCII [ESC] c 1 <n> Hexadecimal 1BH 63H 31H <n> Decimal <27> <99> <49> <n> Range n = 1, 1 n 3, 8 n 11 Description ESC c 1 n selects paper type...

Page 239 - BH 57H xL xH yL yH dxL dxH dyL dyH

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 225 Page Mode The EPOS emulation in the POSjet 1500 supports a similar functionality comparable to the page mode feature. Unlike Epson, the POSjet 1500 supports color and is required to maintain two color plains. This requires tha...

Page 243 - Printing position; Not printed

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 229 The following apply to both GS k <m> <dl> … <dk> NUL GS k <m> <n> <dl> … <dn>: If the horizontal width exceeds the printing area, the printer only feeds the paper. These commands feed ...

Page 244 - Mechanism Control Commands; BEL

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 230 Rev N Nov-10 Mechanism Control Commands Function Select cut mode and cut paper ASCII [GS] V <m> <n> Hexadecimal 1DH 56H <m> <n> Decimal <29> <86> <m> <n> Description When <m> = 1 or 49,...

Page 248 - Macro Function Commands

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 234 Rev N Nov-10 Macro Function Commands Function Start/End Macro Definition EPOS ONLY ASCII [GS] : Hexadecimal 1DH 3AH Decimal < 29> <58> Description The [GS] : command starts or ends macro definition. Macro definition starts when...

Page 249 - User-defined Images and Graphics Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 235 Function Delete Start-Up Macro Definition EPOS ONLY ASCII GS _ Hexadecimal 1DH 5FH Decimal <29> <95> Description The GS _ command deletes a start-up macro definition previously created by the GS ^ command. If a sta...

Page 250 - Hex; Normal

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 236 Rev N Nov-10 Function Print User-Defined Bit Image EPOS ONLY ASCII GS 0 <Name..> <0><m> Hexadecimal 1DH 30H <Name..> 0H<m> Decimal <29> <48> <Name..> <0><m> Range <Name..> =...

Page 251 - dn

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 237 Function Define Single User-Defined Bit-Image EPOS ONLY ASCII GS * x y d 1 … d(x x y x 8) Hexadecimal 1DH 2AH x y d 1 … d(x x y x 8) Decimal <29> <42> x y d 1 … d(x x y x 8) Range 1 x 255 1 y 48 0 d 255 Description...

Page 252 - The report is printed as part of the configuration report.

EPOS Control Codes POSjet ® 1500 Programmer's Guide Page 238 Rev N Nov-10 Function Print single user-defined bit-image EPOS ONLY ASCII GS / <m> Hexadecimal 1DH 2FH <m> Decimal <29> <47> <m> Description The GS / <m> command prints a downloaded or stored bit-image u...

Page 253 - Paper Out/Low Sensor Commands

Programmer's Guide POSjet ® 1500 EPOS Control Codes Nov-10 Rev N Page 239 Ithaca ® Specific POSjet ® Commands The POSjet ® 1500 has a number of extended control commands designed to make operation and maintenance of the printer easier for the host application refer to the POSjet ® extended control d...

Page 258 - Print File Graphics; To generate a print file.

Data Processing and POSjet ® 1500 Programmer's Guide Communications Page 244 Rev N Nov-10 POSjet ® Universal Color Graphics Tthe POSjet ® 1500 Printer firmware supports the ability to print two color graphics in all emulations. This support is an enhancement to the TM-U325D, EPOS, and the Ithaca ® S...

Page 259 - Store Graphics in the printer:

Programmer's Guide POSjet ® 1500 Data Processing and Communications Nov-10 Rev N Page 245 Store Graphics in the printer: PJColor can store a graphic in the POSjet ® 1500 Printer or generate a file that will store a graphic in the printer. To Store a graphic in the printer 1) Start PJColor 2) Under S...

Page 260 - How to use IPCL commands in text strings; Generate a file to store graphics into a printer; ‖ section above; Recall and print stored named graphic image

Data Processing and POSjet ® 1500 Programmer's Guide Communications Page 246 Rev N Nov-10 &%UAxxx Feed xxx dot rows and activate the autocutter. &%UBName& Begin defining universal graphic "Name" &%UGName& End the definition of "Name" &%URName& Run (print) ...

Page 261 - Universal Color Command Descriptions; 500 ignores the command.

Programmer's Guide POSjet ® 1500 Data Processing and Communications Nov-10 Rev N Page 247 Universal Color Command Descriptions Function Begin Named Universal Graphic Record IPCL &%UB <Name..>& Description The &%UB <Name..>& command initializes the universal graphic buffer...

Page 263 - Perform the Feed to cut, Print the Logo and then the Coupon.

Programmer's Guide POSjet ® 1500 Data Processing and Communications Nov-10 Rev N Page 249 POSjet ® Coupon-Cut-Logo Feature The POSjet® 1500 printer has a feature that will allow a coupon and or logo graphic to printed as part of the existing auto cutter command. To activate this feature, it must fir...

Page 264 - Port Protocols and Connection Specifics; Printer Flow Control and Print Buffers; Typical POS System; 500 Printer supports serial or parallel communications.

Data Processing and POSjet ® 1500 Programmer's Guide Communications Page 250 Rev N Nov-10 Port Protocols and Connection Specifics Printer Flow Control and Print Buffers The following figure illustrates the communication flow from host computer to printer and from printer to cash drawer. Cash Drawer ...

Page 265 - 500 Printer supports three flow control protocols, two in

Programmer's Guide POSjet ® 1500 Data Processing and Communications Nov-10 Rev N Page 251 Host computer Data to printer Status and flow control back Printer F i g u r e 3 2 H o s t t o P r i n t e r L in k In most cases, the host computer is capable of sending information to the printer much faster ...

Page 267 - Printer Buffer Size; USB Support and Standards; 500 as a composite device provides the best of both worlds to our

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 253 Printer Buffer Size The POSjet ® 1500 Printer has a configurable buffer size. It can be set from 40 to 8192 bytes. The configurable buffer allows an application to control how far ahead the buffer gets fro...

Page 268 - Two key EZ-USB features that are important to the end user are:; The

Port Protocols and POSjet ® 1500 Programmer's Guide Connection Specifics Page 254 Rev N Nov-10 Two key EZ-USB features that are important to the end user are: 1. The EZ-USB family provides a ―soft‖ (RAM-based) solution that allows unlimited configuration and upgrades. 2. The EZ-USB family delivers f...

Page 269 - Parallel Port; Parallel Port Protocol; Parallel Port Timing; INIT

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 255 Parallel Port Parallel Port Protocol The POSjet ® 1500 parallel port behaves just as any printer connected to a personal computer. The parallel interface accepts 8-bits of data from the host. The strobe si...

Page 270 - Legend; DATA Setup to STB

Port Protocols and POSjet ® 1500 Programmer's Guide Connection Specifics Page 256 Rev N Nov-10 Some systems may wish to change the details of how the strobe, busy, and acknowledged signals interact. The parallel-port option features define how the strobe, busy, and acknowledged signals operate. In n...

Page 271 - Parallel Port Inquire and IEEE 1284; Mode 4

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 257 Parallel Port Inquire and IEEE 1284 The POSjet ® 1500 Printer supports the IEEE 1284 bi-directional, parallel, peripheral interface standard. The IEEE 1284 standard provides for a bidirectional link on the...

Page 272 - Active State; Parallel Port Plug and Play; The Plug and Play response follows.; Device

Port Protocols and POSjet ® 1500 Programmer's Guide Connection Specifics Page 258 Rev N Nov-10 Time-outs IEEE 1284 specifies time-outs for various phases of the protocol. The POSjet ® 1500 Printer treats time-outs as minimums. The printer time outs at the specified period only if it is idle during t...

Page 273 - Serial Port; Serial Port Protocol

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 259 Serial Port Serial Port Protocol The serial port supports two flow control standards, XON/XOFF and Ready/Busy (sometimes called Data Terminal Ready (DTR) or hardware handshake). When Ready/Busy flow contro...

Page 275 - Print Buffer Flow

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 261 Print Buffer Flow The following chart illustrates how the communications driver acquires data from the serial port and places it in the buffer using Ready/Busy or XON/XOFF flow control. F l o w C h a r t 1...

Page 278 - Serial Port Inquire

Port Protocols and POSjet ® 1500 Programmer's Guide Connection Specifics Page 264 Rev N Nov-10 Serial Port Inquire The serial port inquire is more straightforward than parallel mode. The serial acknowledged (ACK) or not acknowledged (NAK) responses follow a uniform format, the ACK or NAK is always f...

Page 279 - Pass Through Restrictions and Considerations

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 265 Display Pass Through The display pass through feature allows a pole display to be interconnected with the printer. The printer is connected to a host system with a specific pin numbered serial cable. The h...

Page 280 - Remote Printer Reset; Reset in Serial Mode; Reset in Parallel Mode

Port Protocols and POSjet ® 1500 Programmer's Guide Connection Specifics Page 266 Rev N Nov-10 Remote Printer Reset Reset in Serial Mode It is possible to generate a software printer reset in serial mode. The [ENQ] <10> command requests that the printer reset. (This is not a hardware reset). T...

Page 281 - Miscellaneous Communication Features

Programmer's Guide POSjet ® 1500 Port Protocols and Connection Specifics Nov-10 Rev N Page 267 Miscellaneous Communication Features Power-cycle Recovery Sometimes the host needs to know if the printer was power cycled. An example would be after the receipt tape was changed. It is not necessary to tu...

Page 282 - Appendix A: Common Operational Questions; Task; Change Ink Cartridges; DO NOT USE ANYTHING OTHER THAN NEW; Entering Configuration Mode

Appendix A POSjet ® 1500 Programmer's Guide Page 268 Rev N Nov-10 Appendix A: Common Operational Questions Task Approach Change Paper Rolls Open the printer‟s front paper cover. Insert the new paper roll so that it unwinds from the bottom and rests on the top of the front cover and aligns with the p...

Page 283 - ASCII Codes; Appendix B: ASCII Code Table

Programmer's Guide POSjet ® 1500 Appendix B ASCII Codes Nov-10 Rev N Page 269 Appendix B: ASCII Code Table Hex Decimal ASCII 00 0 NULL 01 1 SOH 02 2 STX 03 3 ETX 04 4 EOT 05 5 ENQ 06 6 ACK 07 7 BEL 08 8 BS 09 9 HT 0A 10 LF 0B 11 VT 0C 12 FF 0D 13 CR 0E 14 SO 0F 15 SI 10 16 DLE 11 17 DC1 12 18 DC2 13...

Page 284 - Appendix C: Definition Table

Appendix B POSjet ® 1500 Programmer's Guide Page 270 Rev N Nov-10 Appendix C: Definition Table Code Page Country Code/ Language Set Decimal <n 1 ><n 2 > Hex <n 1 ><n 2 > ASCII <n 1 > <n 2 > <n 3 > Epso n ID 64 USA (Slashed 0) 0,64 0H,040H 0,0,6,4 NA 65 USA (...

Page 286 - Appendix D: Ordering Supplies; supplies can be ordered easily direct from the TransAct website (; Drivers Available

Programmer's Guide POSjet ® 1500 Index Page 272 Rev N Nov-10 Appendix D: Ordering Supplies POSjet ® supplies can be ordered easily direct from the TransAct website ( www.transact-tech.com ) or our telephone number within the US toll free: (877) 7ITHACA(877 748 4222). (other inquires: (607) 257 -8901...

Page 287 - Index

Programmer's Guide POSjet ® 1500 Appendix B Nov-10 Rev N Page 273 Index ( ( * ) Button ......................................................................... 19 (USB) Universal Serial Bus ............................................ 253 [ [BEL] Audio alert ...........................................