Epson SureColor F7170- Manuals

U n p a c k i n g t h e P r i n t e r | 5 Media System Assembly The item below can be found in the “Ink Supply System Cover 1” box. b 26 5 E 4 F 2 G 2 D Media feeding unit Take-up reel Reel brackets Adjustment paper Roll core Media guide bar Media guide mounting brackets Bracket alignment tool Mount...

6 | A s s e m b l i n g t h e S t a n d Assembling the Stand Make sure you have the following items before assembling the stand. 1. Remove the tape from the larger horizontal strut, then slide the strut into both of the legs. 2. Use the long end of the hex wrench to tighten the pre-placed screws on ...

A s s e m b l i n g t h e S t a n d | 7 3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the legs. 4. Attach the waste ink tank bracket and secure it with a B screw. 5. Attach one B screw to the other side of the bracket, move the slider into place, then at...

8 | A s s e m b l i n g t h e S t a n d 6. Temporarily fasten the waste ink tube bracket using one B screw. 7. Remove the four screws from each leg, then remove the plastic pieces. 8. Slide the mounting piece into the groove, as shown.

I n s t a l l i n g t h e P r i n t e r | 9 9. Slide the mounting pieces into the grooves, as shown. 10. Replace the plastic pieces and tighten all eight screws. Installing the Printer You need six people to install the printer; four people to carry it and two people to position it on the stand. Use...

I n s t a l l i n g t h e P r i n t e r | 11 2. From the front of the printer, insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are inserted, rotate them counterclockwise 180° to lock them into place. This keeps the printer from slidi...

12 | I n s t a l l i n g t h e P r i n t e r 4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stand’s legs before setting the printer down. 5. Rotate the carry bars clockwise 180° so the locking bolts face the ground. Remove the car...

I n s t a l l i n g t h e P r i n t e r | 13 7. Open the front cover and remove the tape. 8. Remove the media holding plates. 9. Feed the long waste ink tube through the hole in the stand and secure it in place.

14 | I n s t a l l i n g t h e P r i n t e r 10. Open the clips. 11. Slide the waste ink tube into its bracket and close the clips. Gently pull up on the tube to tighten any slack. 12. Remove the cap and inner seal from the waste ink tank. Note: Keep the cap and inner seal for the waste ink tank. Th...

I n s t a l l i n g t h e P r i n t e r | 15 13. Slide the ink splash guard onto the waste ink tube. 14. Install the waste ink tank into the bracket. Make sure the waste ink tube is inserted in the opening. Push the ink splash guard down so that it covers the waste ink tank opening. 15. Place the ca...

16 | I n s t a l l i n g t h e M e d i a F e e d i n g U n i t Installing the Media Feeding Unit You need the following parts to assemble and attach the media feeding unit: Note: Make sure the bracket is oriented correctly when you attach it. 1. Attach the brackets to the back side of the printer wi...

I n s t a l l i n g t h e M e d i a F e e d i n g U n i t | 17 2. Lower the media feeding unit onto the brackets. 3. Attach the media feeding unit to the stand using five C screws. 4. Attach the media feeding unit to the stand using four C screws. Note: Leave the screws loose until the service engin...

18 | I n s t a l l i n g t h e M e d i a F e e d i n g U n i t 5. Run the communication cable through the cable supports. 6. Lift the port cover. 7. Plug in the communication cable and thread it through the cable supports.

I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 19 8. Make sure the communication cable is fully seated in the port and then close the port cover. Installing the Take-up Reel System You need the following parts to assemble and attach the take-up reel system: Note: Make sure the bracket...

20 | I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m Caution: Use at least two people to lift the take-up reel. To avoid damaging the take-up reel, lift it by holding the two bars on the bottom as shown. 2. Lower the take-up reel onto the brackets. 3. Attach the take-up reel using five C...

I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 21 4. Attach the take-up reel to the stand using four C screws. Note: Leave the screws loose until the service engineer finishes adjusting the media system. 5. Connect the communication cable that is attached to the take-up reel system by...

22 | I n s t a l l i n g t h e M e d i a G u i d e B a r Installing the Media Guide Bar You need the following parts to assemble and attach the media feeding unit: 1. Place the mounting bracket over the screws, shift the plate to the right, and tighten the screws. 5 E 4 F a b a

I n s t a l l i n g t h e M e d i a G u i d e B a r | 23 2. Attach two screws to the media guide mounting bracket. 3. Attach a screw to the media guide mounting bracket. 2 E a 1 E a

24 | I n s t a l l i n g t h e M e d i a G u i d e B a r 4. Loosely attach two screws to the stand. 5. Place the bracket over the screws, shift the bracket to the left, then tighten the screws. 6. Attach one side of the media guide bar using two screws. 2 E a a 2 F b

C o n n e c t i n g t o a P o w e r S o u r c e | 25 7. Attach the other side of the media guide bar using two screws. 8. Contact a service engineer to attach the Ink Supply System Cover 1 and adjust the printer. Do not turn on the printer until the service engineer’s work is complete. Connecting to...

26 | S e t t i n g t h e L a n g u a g e 2. Thread the power cords through the cable supports. Connect the power cord to the printer and use the cable supports to restrain the cord. 3. Plug the printer into a properly grounded outlet. Note that two outlets are required, for a total of 20 amps. It is...

L o a d i n g M e d i a | 27 Loading Media 1. Press the P power button to turn on the printer. 2. Open the front cover and then raise the media loading lever.

28 | L o a d i n g M e d i a 3. Loosen the screws on the roll holders and slide the roll holders towards the outside of the printer. 4. Align the left end of the media within the scale.

32 | L o a d i n g M e d i a 11. Lower the media loading lever. 12. Raise the media loading lever and then pull the media through the front of the printer. 13. Pull the media out as shown and ensure that the media is no slack on the left and right side of the roll. Then lower the media loading lever...

L o a d i n g M e d i a | 33 14. Close the front cover. 15. After loading the media, you will be prompted to choose setup and media options. Choose options as necessary. 16. Press the u button to take in the media.

34 | L o a d i n g M e d i a 17. Open the front cover. 18. Attach the media holding plates while aligning their positions. The media holding plates should be installed so that the sides of the media are visible through the three holes and the white line on the media holding plates are visible throug...

I n s t a l l i n g t h e S o f t w a r e | 35 19. Close the front cover. Installing the Software Insert the software CD that came with your printer into your computer and follow the on-screen instructions. You can use USB or Ethernet network connections. • For USB connection, make sure your system ...

36 | U S B I n s t a l l a t i o n USB Installation 1. Press the P power button to turn off the printer, then connect the USB cable to the printer and your computer. 2. Insert the CD into your computer. 3. Follow the on-screen instructions to complete the installation.

N e t w o r k I n s t a l l a t i o n | 37 Network Installation 1. Press the P power button to turn on the printer, if necessary. 2. Connect the Ethernet cable to the printer and your networking device. 3. Insert the CD into your computer.

38 | N e t w o r k I n s t a l l a t i o n 4. Follow the on-screen instructions to complete the installation, keeping the following points in mind: • Do not remove the checkmark from EpsonNet Configuration Utility and EPSON drivers and utilities in the software list. • If you see a firewall or netwo...