Epson PowerLite S1- Manuals

6 Part Names and Functions Before Using the Projector Part Names and Functions Front/Top • remote control infrared receiver s P. 11 Receives signals from the remote control. • ventilation outlet • lens coverAttach when not using the projector to prevent the lens from becoming dirty or damaged. • foc...

7 Part Names and Functions Control panel • [Power] button s P.22 Turns the projector on and off. • Power indicator s P.22 , P.43 Flashes or lights in different colors to indicate the operating status of the projector. • [ u ][ d ][ l ][ r ] buttons s P.33 • [ u ][ d ]: keystone correction buttons s ...

8 Part Names and Functions Rear • Computer/Component Video port s P. 14 , P. 20 Inputs analog video signals from a computer and Component Video g signals from other video sources. • Monitor Out port s P. 16 Outputs the projected analog computer signal to an external monitor. This feature is not avai...

9 Part Names and Functions Base • ceiling mount holes (3 points)Install the optional ceiling mount here when suspending the projector from the ceiling. • lamp cover s P.57 Open this cover when replacing the lamp inside the projector. • air filter (air intake vent) s P.55 , P.59 Prevents dust and oth...

10 Remote Control Remote Control • remote control infrared transmitterTransmits remote control signals. • [Aspect] button s P.31 Changes the aspect ratio of images from 4:3 to 16:9. • [Source] buttons s P.28 [Computer]: Switches to the signal source being input to the Computer/Component Video port.[...

11 Remote Control Before using the Remote Control Remove the insulating tape. Using the Remote Control Operate the remote control by aiming it at the remote control infrared receiver on the projector. Operating range Operable distance: Max. approximately 20 feet (6 m) (May be shorter depending on co...

12 Installation Installation Installation method Set up the projector so that it is at right angles to a screen. Projection distance and screen size c Be sure to read the Important Safety Instructions before installation. p When setting up the projector against a wall, leave a space of at least 7.9 ...

13 Installation Other installation methods Rear projection (Using a translucent screen) Ceiling projection Ceiling/Rear projection (Using a translucent screen) The optional ceiling mount is required when installing the projector from a ceiling. Please contact your dealer if you wish to use this meth...

14 Connecting to a Computer Connecting to a Computer Compatible computers Condition 1: Check that the computer has an image output port, such as an RGB port, monitor port or CRT port. Some computers with a built-in monitor and some notebook computers may not be compatible. Please refer to your compu...

15 Connecting to a Computer When using a 5BNC port When using a 13w3 port Playing sound from a computer You can play sound from a computer through the projector’s built-in speaker. Volume adjustment Press [ l ] or [ r ] on the remote control. You can also adjust the volume from the configuration men...

16 Connecting to a Computer Connecting to an external monitor The image being input into the projector can be displayed on a computer monitor. Presentation Remote Control You can use the presentation remote control as a wireless mouse to control the mouse pointer on the computer screen.The presentat...

17 Connecting to a Computer Installing the driver for Windows Screen contents will differ according to the version of Windows you are using. This explanation uses screenshots taken from Windows 98. Driver installation is not required for the Macintosh. 1 Connect the accessory Presentation Remote Rec...

20 Connecting to Video Equipment Operating range Operable distance: Maximum approximately 20 feet (6 m) (may be shorter depending on conditions) Operable angle: Approximately 30° horizontally, 15° vertically Connecting to Video Equipment Projecting video images For Composite Video (DVD, VHS, Video g...

21 Connecting to Video Equipment For Component Video (DVD, Video games) For RGB Video Playing sound from video equipment Volume adjustment Press [ l ] or [ r ] on the remote control. You can also adjust the volume with the configuration menu. ([Menu] button → “Setting” → “Volume”) See “Setting menu”...

22 Turning on the Projector Basic Operation Turning on the Projector 1 Connect the computer/video. See “Connecting to a Computer” on page 14 , “Connecting to Video Equipment” on page 20 . 2 Remove the lens cover. 3 Attach the power cable to the projector. 4 Insert the power plug into a wall socket. ...

24 Turning off the Projector Turning off the Projector 1 Turn off the power to the computer/video equipment. 2 Press the [Power] button. A confirmation screen is displayed. 3 Press the [Power] button again. The power indicator begins to blink. 4 Wait until the power indicator lights orange. Cool-dow...

25 Adjusting the Display Adjusting the Display Adjusting the projection size The size of the projected image is basically determined by the distance from the projector to the screen. See “Projection distance and screen size” on page 12 . 1 Press the [Wide] or [Tele] buttons on the control panel to a...

26 Adjusting the Display Adjusting the projection angle 1 Set up the projector so that it is at right angles to the screen. If it is not possible to set up the projector so that it is at right angles to the screen, it can be set up at a slight vertical angle instead. (Max 10°) 2 Raise the front of t...

27 Adjusting the Display Keystone When the projector is not set at right angles to the screen, the display distorts in the shape of a trapezoid. This distortion can be corrected. Press the [ u ] or [ d ] buttons. Images can be corrected without distortion when the projector is tilted to a maximum of...

28 Selecting the Input Source Selecting the Input Source When a device is connected, projection commences automatically without having to select the input source, however when connected to two or more devices, you need to switch between the input sources. Projector The input source changes each time...

29 Functions for Enhancing Projection Advanced Operation Functions for Enhancing Projection Adjusting computer generated images The computer signal is analyzed and the following settings are adjusted to ensure the optimum image quality. ◗ Tracking g ◗ Position ◗ Sync. g When Auto setup is set to off...

30 Functions for Enhancing Projection The color mode changes each time you press the [Color Mode] button on the remote control. Dynamic → Presentation → Theatre → Living Room → sRGB Default Value ◗ Computer input: Presentation ◗ Other input: Dynamic A/V Mute Temporarily stops the image and sound. ◗ ...

31 Functions for Enhancing Projection Projecting in widescreen (changing aspect ratio) This function changes the Aspect ratio g of images from 4:3 to 16:9 when component video images (YCbCr and YPbPr) or video images (S-Video or composite video) are being projected. Images which have been recorded i...

32 Configuration Menus Configuration Menus Various adjustments and settings can be made within the configuration menus. Depending on your video source, some settings may not be available. Image r r Color Mode Image r r Color Mode (Computer Images) (Video Images) r Picture Quality r r Brightness r Pi...

33 Configuration Menus Menu operation 1 Press the [Menu] button The top configuration menu is displayed. 2 Press the [ u ] or [ d ] buttons to select the Top Menu item. Top Menu Sub Menu 1

36 Configuration Menus Function list Image menu • When no signal is being input, only the settings for “Auto Setup” and “Input Signal” can be adjusted. • The functions in the “Image” Menu will be different according to the type of signal which is being input. “Input Signal” only appears on menu scre...

39 Configuration Menus Setting menu Sub menu Function Screen Keystone Corrects vertical keystone distortion in the image. The projected image changes when keystone correction is carried out. If the images become uneven in appearance after keystone correction has been carried out, decrease the sharpn...

41 Configuration Menus Info menu Computer images Video images Sub menu Function Lamp Hours Displays the cumulative lamp operating time. When the accumulated usage time of the lamp reaches about 1900 hours, a warning will be displayed in red. Source Displays the input source being projected. Input Si...

42 Configuration Menus Reset menu Sub menu Function Lamp-Hours Reset Resets the lamp operating time. When this command is selected, the cumulative lamp operating time is reset to the default value. All Reset Resets all items in the configuration menus to their default settings. • Press the [ e ] but...

43 When You Suspect a Problem Troubleshooting When You Suspect a Problem First, check the indicators on the projector. There are two indicators on the projector unit which notify you of projector conditions. Power indicator lit flashing • If the indicator is not lit, the power supply is not on. Powe...

45 When You Suspect a Problem When the indicators provide no help • No images appear (Nothing is displayed) page 45 • No images appear (Messages are displayed 1) page 46 • No images appear (Messages are displayed 2) page 46 • Image is out of focus (unclear) page 47 • Vertical stripes appear in the i...

46 When You Suspect a Problem No images appear (Messages are displayed 1) No images appear (Messages are displayed 2) “Not supported” • Check the mode which corresponds to the frequency of the image signals being output from the computer. Refer to the documentation provided with your computer for de...

48 When You Suspect a Problem Vertical stripes appear in the image Image is distorted / Image contains interference • Has the “ Tracking g ” setting been adjusted? Set the tracking value until the vertical stripes disappear. ([Menu] button → “Image” → “Picture Quality” → “Tracking”) See “Image menu”...

50 When You Suspect a Problem Image colors are poor, tinted green or tinted red/purple • Are the image signal format settings correct? If a component video device is connected and “Computer” is set as the “Image” → “Input Signal” configuration menu setting, the projected images will appear greenish....

51 When You Suspect a Problem Image is dark No sound can be heard • Does the lamp need replacement? When the lamp is due for replacement, colors will weaken and the image will become dark. Replace the lamp when this is the case. See “Lamp replacement period” on page 56 . • Has the image brightness b...

52 When You Suspect a Problem The remote control does not work The power does not turn off (after the [Power] button is pressed) • Is direct sunlight or strong light from fluorescent lamps shining onto the remote control infrared receiver? See “Using the Remote Control” on page 11 . • Is the remote ...

53 Where to Get Help Where to Get Help EPSON provides technical assistance through electronic support services 24 hours a day, as listed in the following table. Telephone Support Services To use the EPSON PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included EPSON Privat...

54 Projector Care Appendix Projector Care Be sure to read the Important Safety Instructions before proceeding. Cleaning You should clean the projector if it becomes dirty or if the projected image starts to deteriorate. Cleaning the projector case Clean the projector case by wiping it gently with a ...

55 Projector Care Cleaning the air filter If the air filter becomes clogged with dust, it can cause overheating and damage the projector. Keeping the projector horizontal, use a vacuum cleaner to clean away the dust from the air filter. p • If the air filter is difficult to clean or if it is broken,...

56 Projector Care Replacing consumables Changing the battery (Remote Control, Presentation Remote Control) Replacement battery: 1 × CR2025 lithium battery 1 Remove the battery holder. While pressing the catch of the battery holder inwards, pull the battery holder out. 2 Remove the old battery and in...

57 Projector Care Replacing the lamp 1 Turn off the projector and wait for the cool-down period to end. (Approximately 20 seconds) 2 Unplug the power cable and remove it, then wait for the lamp to cool down. (Approximately 1 hour) 3 Open the lamp cover. Push in the tabs on the lamp cover and push it...

58 Projector Care 7 Replace the lamp cover. First insert the tabs, and then press down on the opposite side until it clicks into place. Resetting the lamp operating time The projector has a built-in counter which keeps track of the lamp operating time and causes the replacement warning message to be...

59 Projector Care 3 Use the [ l ][ r ] buttons to select “Yes,” then press the [ e ] button. The lamp operating time will be reset. Replacing the air filter Replacing the air filter can also be performed when the projector is mounted to a ceiling. 1 Turn off the projector power, wait for the cool-do...

60 Optional Accessories Optional Accessories You can purchase screens, carrying cases, or other accessories from EPSON at (800) 873-7766 or by visiting the EPSON Store at www.epsonstore.com (U.S. sales only). In Canada, please call (800) 463-7766 for dealer referral . This list of optional accessori...

61 Glossary Glossary Complex terms used in this book, or terms not explained in the body of the text, will be briefly explained here. For further explanation, please consult commercially available reference texts. 5BNC A type of connector used to input analog video signals. Aspect ratio The ratio be...

63 Cable Format Cable Format Serial connection ◗ Connector type: D-Sub 9-pin (male) ◗ Projector input port type: RS-232C Projector Computer Projector (PC serial cable) Computer Signal name Function GND Signal line grounding TD Transmitting data RD Receiving data DSR Data set ready DTR Data terminal ...

64 Supported Display Resolutions Supported Display Resolutions Computer * Connection is not possible if the equipment does not have a VGA output port. Component Video Composite Video/S-Video It may be possible to project signals which are not listed in the above table. However, not all functions may...

65 Specifications Specifications Pixelworks TM ICs are used in this projector. Product name EPSON PowerLite S1 LCD Projector Safety USAUL1950 3 rd Edition CanadaCSA C22.2 No.950-95 (cUL)European CommunityThe Low Voltage Directive (73/23/EEC)IEC60950 2 nd Edition, +Amd.1, +Amd.2, +Amd.3, +Amd.4 EMC U...

66 Important Safety Instructions Important Safety Instructions Please read the following important information about your projector. Follow these safety instructions when setting up and using the projector: ◗ Do not place the projector on an unstable cart, stand, or table. ◗ Do not use the projector...

68 FCC Compliance Statement We: EPSON AMERICA, INC. Located at: 3840 Kilroy Airport WayMS: 3-13Long Beach, CA 90806 Tel: 562-290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product mar...

69 Warranty Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc. (“EPSON”) warrants to the first end user customer of the EPSON product enclosed with this limited warranty statement that the product, if purchased and used...

70 Index 13w3 port ........................................................................................................... 155BNC port .......................................................................................................... 15 A A/V Mute ...........................................