Epson P6000 - Manuals

A s s e m b l i n g t h e s t a n d | 5 Assembling the stand 1. Make sure you have all of these items: 2. Insert the strut into the left side of the stand. (The sides of the stand are labeled L and R. ) 2 sides Horizontal strut Hex wrench 6 bolts

6 | A s s e m b l i n g t h e s t a n d 3. Fasten the strut with 3 bolts. Use the hex wrench to tighten the bolts. 4. Insert the strut into the right side and fasten it with 3 bolts. Note: Make sure you tighten all bolts before moving to the next step.

M o u n t i n g t h e p r i n t e r o n t h e s t a n d | 7 5. Lock the casters. Mounting the printer on the stand 1. Make sure you have these items: 2. Remove the cardboard panels and other printer packing materials. Printer 2 wing screws withlock washers

8 | M o u n t i n g t h e p r i n t e r o n t h e s t a n d 3. Lift the printer and mount it on the stand, aligning the pegs with the holes on the bottom of the printer. WARNING: Four or more people are required to lift the printer. 4. Insert the printer to the stand with the wing screws and washers...

14 | A t t a c h i n g t h e p a p e r b a s k e t ( S C - P 6 0 0 0 / S C - P 7 0 0 0 ) 11. Insert the rod into the fabric channel. 12. Insert the free ends of the rod into the holes in the sides of the stand.

A t t a c h i n g t h e p a p e r b a s k e t ( S C - P 8 0 0 0 / S C - P 9 0 0 0 ) | 23 15. Insert the free ends of the rod into the holes in the sides of the stand. 16. Loop the tabs over the rod

24 | I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r 17. Attach the paper guides to the bottom of the printer. Installing the optional internal print server If you purchased the optional internal print server (part number C12C848031), follow these steps to install it ...

I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r | 25 2. Remove the two screws securing the option slot cover to the back of the printer, then remove the cover. Note: Make sure you save the option slot cover. Remove the internal print server and re-attach the cover if ...

26 | C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d 4. Secure the internal print server using the screws you removed. Completing setup and connecting the power cord 1. Attach the manual holder to the left or right side of the stand. Store this Setup guide and the Qui...

C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d | 27 3. Remove any packing tape and plastic film. Check these areas: • the front cover • the ink compartment covers • the maintenance tank(s) 4. Open the roll paper cover and remove the tape and packing material.

28 | C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d 5. Open the front cover and remove the tape and packing material. Note: Save the packing material in case you need to ship the printer. 6. Close the front cover. 7. Connect the power cord to the AC inlet on the back...

I n s t a l l i n g i n k | 29 8. Attach the cable guides to the left or right side of the printer back and route the power cord to the side of the printer as shown. 9. For the SC-P8000/SC-P9000, attach the loops on the paper basket cords to the cable guides. 10. Plug the power cord into a properly ...

30 | I n s t a l l i n g i n k The cartridges shipped with your printer are provided mainly to charge the ink system. Make sure you order a new set of cartridges as soon as possible. 1. Press the P power button to turn on the printer. 2. Select the language, date/time, and units of measurment for th...

32 | I n s t a l l i n g i n k Hold each cartridge with the arrow pointing toward the printer, then insert it into its slot until it clicks into place. Make sure you insert each cartridge all the way into the correct slot. 6. After installing all of the cartridges, close the ink covers. The printer ...

L o a d i n g r o l l p a p e r | 33 Loading roll paper You can use roll paper with a 2- or 3-inch core and a width of up to 24 inches (61 cm) for the SC-P6000/SC-P7000, or 44 inches (112 cm) for the SC-P8000/SC-P9000. Placing roll paper in the printer 1. Open the roll paper cover.

34 | P l a c i n g r o l l p a p e r i n t h e p r i n t e r 2. Push the lock lever down firmly, then move the roll paper holder to the left. Note: Make sure you push the lock lever all the way down. If the lever is raised at all, the lock is still on. 3. Place the roll on top of the printer.

P l a c i n g r o l l p a p e r i n t h e p r i n t e r | 35 4. If necessary, adjust the roll media adapters to fit the core size of the roll paper. 2-inch core: 3-inch core: 5. Release the tension lever on both adapters.

P l a c i n g r o l l p a p e r i n t h e p r i n t e r | 37 8. Slide the roll paper holder to align the left adapter with the u on the holder. 9. Roll the paper slowly into position.

38 | P l a c i n g r o l l p a p e r i n t h e p r i n t e r 10. Slide the roll paper holder to the right to secure it in the printer. Make sure both ends of the roll paper are secured in the adapters. 11. Pull up the lock lever to lock the paper in place. 12. If the light is not on, press the butto...

L o a d i n g r o l l p a p e r f o r p r i n t i n g | 39 Loading roll paper for printing 1. Insert the paper into the slot and pull it down until the edge of the paper is in the center of the stand. If the paper doesn’t come out, you may need to decrease the suction by pressing the d Paper Feed bu...

40 | A l i g n i n g t h e p r i n t h e a d 5. On the screen that appears on the LCD screen, select Keep Settings Above if the paper settings are correct, or select Change Settings , then adjust the settings. 6. Press OK . To avoid indenting or creasing the paper, remove it from the paper path and ...

C o n n e c t i n g t o y o u r s y s t e m | 41 Connecting to your system You can use a USB and/or an Ethernet network connection. For a USB connection, make sure your system has the appropriate port and you have a standard, shielded cable 10 feet (6 m) long or less. To connect to a network hub, yo...

42 | I n s t a l l i n g t h e s o f t w a r e Installing the software Download and run your product’s software package: • www.epson.com/support/p6000 (U.S.) or www.epson.ca/support/p6000 (Canada) • www.epson.com/support/p7000 (U.S.) or www.epson.ca/support/p7000 (Canada) • www.epson.com/support/p80...

C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k | 43 3. Click Acquire Latest Information to automatically download the latest firmware version for your printer from the internet. If there is a firmware update, the message “Found the latest firmware information. Do you want to d...

44 | C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. General Notice: Other product names used herein are for identification purposes only and may be ...

Setup CPD-50156 Printed in USA Epson ® SureColor ® P-Series P6000/P7000/P8000/P9000 CPD50156_SureColor P6000-P9000_Setup_E.indd 1 8/19/15 4:04 PM